FULHAM CTBRCB02JM02 600W Lighting Controller Instructions

: June 10, 2024
: FULHAM

Table of Contents

CTBRCB02JM02 600W Lighting Controller
Product Information
Product Usage Instructions

CTBRCB02JM02 600W Lighting Controller

FULHAM CTBRCB02JM02 600W Lighting Controller Instructions-
product

Product Information

Output Wattage: 600W Max
Universal Voltage: 120-277VAC
Dimming Controller Type: 0-10Vdc Type / Channels
Communication Type: RF
Transmission Range: Not specified
Ambient Operating Temperature Range: Not specified
Maximum Driver Case Temperature (Tc) (Per UL): Not specified
Input Surge Protection: Yes
Mounting Type: 1/2 Knockout Mount IP66
Overall Size: Not specified
Protections:
- FCC ID : 2AJ9LCTRCB0XJM0XXXX, RoHS COMPLIANT, IP66
Weight: 15 pounds
Sound Rating: Not specified
Service Life: Not specified
Warranty: Not specified

Product Usage Instructions

To use this lighting controller, follow these instructions:

Ensure that the input voltage and frequency match the specifications of the product, which are 120 – 277VAC (+/- 10%), 50-60Hz.
Connect the input wires to the appropriate power source.
Connect the output wires to the luminaire you wish to control.
If necessary, connect the dimming controller using the 0-10Vdc Type / Channels connection.
If desired, set up RF communication by following the instructions provided with the product.
Install the lighting controller using the 1/2 Knockout Mount IP66 mounting type.
Ensure that the product is protected from input surges.
Test the product to ensure it is functioning properly.

SPECIFICATION INSTRUCTIONS

Lighting Controller

Output Wattage: 600W Max.
Universal Voltage (120-277VAC)
0-10V Luminaire
1/2” Knockout Mount
IP66
FCC ID : 2AJ9LCTRCB0XJM0XXXX

General Speciﬁcations

FULHAM CTBRCB02JM02 600W Lighting Controller
Instructions-fig-9

Fulham EliteBlue

Fulham’s EliteBlue commissioning app can be found on the Apple app store by searching “EliteBlue”. For web app, please visit https://eliteblue.fulham.com

Complete commissioning manual can be found at:
https://www.fulham.com/PDFs/eliteBlue-commissioning-manual.pdf

Mechanical Data

WIRING DIAGRAMS#10-24*1 inch
Mounting hole for threaded pipe: 7/8” (22mm) FULHAM CTBRCB02JM02 600W
Lighting Controller Instructions-fig-2

Notes:

Driver has two (2) mounting tabs with a round hole in each.
Fasten a screw through the mounting tab if mounted on a ﬂat surface.

Overall Dimensions

FULHAM CTBRCB02JM02 600W Lighting Controller
Instructions-fig-3

WIRING DIAGRAMS

FULHAM CTBRCB02JM02 600W Lighting Controller
Instructions-fig-4

Notes:
Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with all applicable codes and standards, including ﬁre-rated construction.

FCC Caution.

This device complies with part 15 of the FCC Rules. Operation Is subject to the followlng two conditions:

Th is device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user”s authority to operate the equipment.

Restoring Factory Settings

To reset the unit you will need to place and hold a magnet for 10 seconds on the reset icon on the location of the unit shown in the image below.
Once the magnet has been placed the Indicator Light will stay lit and begin to flash until it shuts off indicating that the unit has been successfully reset.
Remove the magnet from the unit, the Indicator Light will light up and flash repeatedly
The unit is now ready to be provisioned.