CREALITY 3DPrintMill CR-30 Printmill 3D Printer User Manual

CREALITY 3DPrintMill CR-30 Printmill 3D Printer User Manual

Content
Dear Consumers, Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer. Our teams will always be ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer. For a better experience in using our product, you can also learn how to use the Printer in the following ways: View the accompanied instructions and videos in the storage card. Visit our official website www.creality.com to find relevant software/hardware information, contact details and operation and maintenance instructions.

A. Notes
B, Assemble the 3D Printer
C. Use the 3D Printer
Load Filament
Start Printing

NOTE

1. Do not use the printer any way other than described herein in order to avoid personal injury or property damage.
2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
3. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
4. Please use recommended resin to in case damage of machine.
5. Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.
6. Please do not open the plastic cover during usage, otherwise the printing will be interrupted.
7. Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage.
8. Please wait a moment after the print is finished. And please wear gloves to take out the print by tools.
9. Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame, guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface.
10. Children under 10 years should not use the printer without supervision.
11. This machine is equipped with a security protection mechanism. Do not manually move the nozzle or printing platform mechanism manually while booting up, otherwise the device will automatically power off for safety.
12. Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators’ legal liability under any circustance.

Introduction

1. motor
2. Belt tensioning screw
3. Y motor
4. Storage card slot and USB socket
5. Nozzle kit
6. Manual power switch
7. Material rack and material tube
8. Y-axis limit adjustment component
9. Printing platform
10. X axis limit switch
11. Knob screen
12. Z axis belt motor
13. Bed leveling nut
14. Extruder
15. Knob
16. Power cable connection

Parameters

| Basic Parameters
---|---
Model| 3DPrintMil
Print size| Infinite length200170mm (lengthwidthheight)
Molding technology| FDM
Number of nozzle| 1
Layer thickness| 0.1mm-0.4mm
Nozzle diameter| Standard 0.4mm
XY axis precision| ±0.1mm
Filament| PLA/TPU/PETG
File format| STL/OBJ/AMF
File transfer| Storage card
Compatible slicing software| CrealityBelt
Power specification| Input ：100-120/200-240V 50/60Hz Output ：24V/14.6A
Total power| 350W
Hotbed temperature| 0-100°C
Nozzle temperature| 0-240°C
Resume printing function| Yes
Filament sensor| Yes
Dual z-axis screws| No
Language switch| English
Computer operating system| Windows XP/Vista/7/10
Print speed| ≤180mm/s, 30-60mm/s normally

Parts List

1. X/Y axis belt assembly
   

2. Bottom belt assembly x 1

3. Display kit x 1
   

4. Spool holder x 1

5. Filament x 1

6. Profile bracket 1 x

7. Profile bracket 2 x 1

8. Storage card and card reader x 1

9. Diagonal pliers x 1

10. Cable tie x 10

11. Needle x 1

12. Blue line claw x 2

13. Pneumatic connector x 2

14. Power cord x 1

15. Wrenches and screwdrivers x 1

16. M5T nuts x 6

17. Photoelectric switch line x 1

18. Hexagon socket flat round head screw M5X8 x 6

19. Hexagon socket flat round head screw M5X12 x 6

20. Hexagon socket flat round head screw M5X18 x 10

21. Hexagon socket head spring washer combination screw M5X45 x4

22. Hexagon socket head spring washer combination screw M5X12 x 4

23. Teflon tube x 1

24. Nozzles x 2

25. Socket wrench x 1

26. Feeler x 1

Install the Profile Support Frame

1. Bottom belt assembly x 1
   

2. Profile bracket 1 x 1

3. Profile bracket 2 x 1

4. Hexagon socket flat round head screw M5X12 x 4

  Step: Install the profile support 1 and profile support 2 to the bottom of machine with four hexagon flat head screws M5x12 (As shown in the figure above).

Install X/Y Axis Belt Assembly

1. X/Y axis belt assembly x 1

2. 0 Hexagon socket flat round head screw M5X18 x 8

3. Hexagon socket head spring washer combination screw M5X12 x 2

4. Hexagon socket head spring washer combination screw M5X45 x2

Please loosen the two screws of extrusion motor first if there is interference between the profile bracket 2 and X/Y-axis assembly before proceeding and tighten up the two screws after assembly (as shown in figure1).

Install the Spool Holder

1. Spool holderx 1

2. M5T nuts x 2

3. Hexagon socket flat round head screw M5X8 x 2

Install the Display

1. M5T nuts x 2

2. Hexagon socket flat round head screw M5X8 x 2

Step: Lock the display assembly with two M5X8 flat head screws and two M5 T-nuts, as shown in the figure above;

Cable Connection

1. Power cord x 1

Leveling

1. First move the X axis to the contact part between the nozzle and the belt (slightly press the nozzle onto the belt ) .
2. Push the two limit switches against the X sliding block to lock the limit;
3. Press back on the screen to get the printer back to the origin; adjust the Y axis end-stop adjusting screw according to the position of the nozzle relative to the belt after back to the origin in order to make sure the nozzle contacting with the belt rightly; then tighten the Y axis end-stop screw, leveling finished;
4. if there is any seam or over contact between the nozzle and the belt, adjust the leveling nut slightly.
   
   

Preheating

Notes : The UI information is only for reference, the actual UI may be different.

When you wait for the temperature to rise, hang the filament over the filament holder.

For smoother printing, the end of the filament should be placed as shown above.

Load Filament
When the current temperature reaches the target temperature, press and hold the spring of the extruder and insert the consumables into the charging detection hole one by one, then insert the consumables into the small hole of the extruder until the nozzle position.

Tips : How to Replace the Filament? Withdrawing the filament quickly and feeding the new filament after nozzle preheated and filament pushed a little forward.

Start printing

1. Double click to install the software.

2. Double click to open the software.

3. Select language-■close–cossetting -bawd corresponding model-printer setting ‘close-customized-■ confab gyration -member of prints to complete the setting.

4. Open the file in turn → select the file
   

5. Generate G-code, and save the gcode file to storage card.
   

6. Insert the storage card→ print from card→select the file to be printed
   

File names must be Latin letters or numbers, not Chinese characters or other special symbols.

Notes: For details on the software instructions, please refer to the slicing software manual in the storage card!

Circuit Wiring

Trouble-Shooting

Due to the differences between different machine models, the physical objects and the final images can differ The final explanation rights shall be reserved by Shenzhen Reality 3D Technology Co., Ltd.

SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD.
stage 18,District Longueil, Shenzhen, Chine, 5181311

SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD. Acici:18F,JinXiuHongDu Building, Meilong Blvd., Longhua Dist..
Shenzhen, China 518131
Official Website: vAvw.creality.com
Tel: +86 755-8523 4565
E-mail: info@creality.com cs@creality.com

Scan To Learn Mor

References

• Creality - Global Leader in Consumer-Level 3D Printer Ecosystems and Creator
• Weltweit führender 3D-Drucker & Filament-Anbieter für Maker und Profis | Creality 3D
• 创想三维(CREALITY) - 3D打印机,教育/工业3D打印机领导品牌

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>