Schneider Electric METSEPMRS4854W PowerLogic Communication Module Instruction Manual

Schneider Electric METSEPMRS4854W PowerLogic Communication Module Instruction Manual

Dimensions

Safety precautions

⚠ DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate Personal Protective Equipment (PPE) and follow safe electrical work practices. See NFPA 70E, CSA Z462 or other local standards.
• Turn off all power supplying this device and the equipment in which it is installed before working on or in the equipment.
• Always use a properly rated voltage sensing device to confirm that all power is off.
• Do not exceed the maximum ratings of this device.
• Do not use this device for critical control or protection of persons, animals, property or equipment.
• Assume communications and I/O wiring are hazardous live until determined otherwise.

Failure to follow these instructions will result in death or serious injury.

Mounting

Wiring diagrams

Description

Verification

Used as Gateway

1. Type meter’s IP address in a web browser to connect to meter’s webpage.

2. Navigate to Setup > Serial Port.

3. Configure the following settings to match your connection:
   • COM1/RS485#1 – Protocol
   • COM1/RS485#1 – Baud Rate
   • COM1/RS485#1 – Unit ID
   • COM1/RS485#1 – Bias = ON

4. Navigate to Diagnostics > Serial Port to verify meter is communicating properly.

Used as a direct Serial Device

1. On the meter front panel, press the Home button.

2. Navigate to Setup Menu > Communications Setup > COM1 Setup screen.

3. Verify the following settings to match your serial connection:
   • COM1 – Protocol
   • COM1 – Baud Rate
   • COM1 – Unit ID
   • COM1 – Serial Port
   • COM1 – Bias = OFF

4. Use ION Setup to view device settings to verify meter is communicating properly.

Specifications

Input

• Number of ports: 1
• Type: RS-485 / RS-422
• Cable type: Shielded twisted pair
  *Data pairs (+/-) should be twisted pair

Environment

• −25 to 70 °C (−13 to 158 °F) operating temperature

• Maximum operating temperature is based on the quantity and type of attached option modules:

• 5% to 95% RH non-condensing

• Maximum dewpoint 37 °C (99 °F) −40 to 85 °C (−40 to 185 °F) storage temperature

• Pollution degree 2

• < 3000 m (9843 ft.) above sea level

• IP30

• Not suitable for wet locations

• For indoor use only

Notices
Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it.
Electrical equipment should be installed, operated, serviced and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. A qualified person is one who has skills and knowledge related to the construction, installation, and operation of electrical equipment and has received safety training to recognize and avoid the hazards involved.
Power Logic and Schneider Electric are trademarks or registered trademarks of Schneider Electric in France, the USA and other countries.

• This product must be installed, connected and used in compliance with prevailing standards and/or installation regulations.
• If this product is used in a manner not specified by the manufacturer, the protection provided by the product may be impaired.
• The safety of any system incorporating this product is the responsibility of the assembler/installer of the system. As standards, specifications and designs change from time to time, always ask for confirmation of the information given in this publication.

Schneider Electric 35 rue Joseph Monier 92500 Rueil Malmaison France
www.se.comhttps://www.productinfo.schneider- electric.com/portals/ui/ION9000/www.se.com/ww/en/download/search/METSEPMRS4854W/https://www.youtube.com/user/SchneiderCorporate

NNZ39768-00 © 2021 Schneider Electric. All rights reserved. 10/2021

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>