BRANDMOTION FVMR-1180 FullVUE Rear Camera Mirror for Ford Super Duty 1999 to 2016 User Manual
- June 10, 2024
- BRANDMOTION
Table of Contents
FullVUE® Rear Camera Mirror for Ford
Super Duty (1999 – 2016)
FVMR-1180
FVMR-1180 FullVUE Rear Camera Mirror for Ford Super Duty 1999 to 2016
FullVUE® Rear Camera Mirror – FVMR-1180
Kit Contents
Components for installing the FVMR-1180
Kit Contents: FullVUE® Mirror & Harness 3rd Brake Light Bezel & Camera 9m
Camera Harness
Part 1
Attaching the FullVUE® Mirror to the windshield
- Remove the old mirror from the mount on the windshield as per manufacturer’s directions. Be sure to use the proper removal tool if required.
- Install new mirror onto the D-tab and tighten with a Phillips screwdriver.
CAUTION Take care not to overtighten.
Overtightening could result in damage to your windshield.
Part 2
Powering the FullVUE® Mirror
- Connect the power harness to the plug on the mirror. Route the harness across the top of the head liner, along the windshield, and down the A-pillar, and to the desired location in the kick panel.
- Ensure that the harness will not be pinched when trim panels are replaced.
Part 3
Wiring the FullVUE Mirror
- Connect the RED wire from the mirror harness to 12-volt accessory power.
- Connect the YELLOW wire from the mirror harness to 12-volt constant power.
- Connect the BLACK wire to a solid ground. Chassis ground in the kick panel is recommended.
Part 4
Function test of the FullVUE Mirror
- Turn the vehicle ignition on and see if you are seeing the front camera displayed on the screen. Turn off the ignition and the mirror will power down
Disassembly
Part 1
Removing the third brake light
- Use a Phillips screwdriver to remove the screws on either side of the brake light
- Pull the brake light out from the cab. Be Careful not to damage the foam gasket around the opening.
- Disconnect the power connector from the light.
Running Wires
Part 1
Video Connector
- Connect the 9m camera harness to the mirror harness at the connection by the mirror.
- Run the 9m camera harness from the FullVUE Mirror through the headliner toward the brake light.
- Pull the video connector of the 9m camera harness through the grommet to the outside of the cab.
Assembly
Part 1
Assembling the Bezel
-
Attach the thick foam gasket to the back side of the bezel or to the light. Whichever piece does not have a foam gasket from the factory.
Note: The cable for the camera must go through the channel of the bezel before the foam is put overtop -
Put the foam side of the bezel against the vehicle.
-
Connect the rear camera harness to the camera. Make sure to line up the arrows on the connectors
-
Plug the brake light back into the cab plug
-
Put the screws through the hole of the light and insert the light into the bezel.
-
Use the screws that are showing through the bezel to line up with the screw holes of the vehicle. ( Be careful not to scratch the vehicle.)
-
Screw the assembly back together with the factory screws.
Adjustment
Part 1
Bezel Viewing Adjustment
- If you need to change the camera’s pitch, gently bend the bracket until it reaches the desired view angle.
AR_1_10_2023
FullVUE® Rear Camera Mirror – FVMR-1180
Vehicle Application: Ford Super Duty (1999 – 2016)
Part Number: FVMR-1180
Documents / Resources
|
BRANDMOTION FVMR-1180 FullVUE Rear Camera Mirror for Ford Super Duty 1999 to
2016
[pdf] User Manual
FVMR-1180, FVMR-1180 FullVUE Rear Camera Mirror for Ford Super Duty 1999 to
2016, FullVUE Rear Camera Mirror for Ford Super Duty 1999 to 2016, FVMR-1180
FullVUE Rear Camera Mirror, FullVUE Rear Camera Mirror, Rear Camera Mirror,
Camera Mirror, Mirror
---|---
|
BRANDMOTION FVMR-1180 FullVUE Rear Camera Mirror for Ford Super
Duty
[pdf] Instruction Manual
FVMR-1180 FullVUE Rear Camera Mirror for Ford Super Duty, FVMR-1180, FullVUE
Rear Camera Mirror for Ford Super Duty, FullVUE Rear Camera Mirror, Rear
Camera Mirror, Camera Mirror, Mirror
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>