BLAUPUNKT GT3010 Grass Trimmer Instruction Manual

BLAUPUNKT GT3010 Grass Trimmer

Product Information

GT3010 Electric Grass Trimmer

The GT3010 Electric Grass Trimmer is a gardening tool designed for home use to trim grass and weeds in areas that cannot be reached with a lawnmower. It features a switch, main handle, middle tube, motor housing, bracket, reel, reel cover, safety guard, power cord, cord holder, additional handle, and mounting screws.

Intended Use

The GT3010 Electric Grass Trimmer is intended for home use only and not for commercial or industrial use. Use it to trim grass and weeds in areas that cannot be reached with a lawnmower.

Device Assembly

To assemble the device, connect the upper part to the centre tube holder and screw the screw into place. Then, connect the middle part to the motor housing bracket and screw the screw into place.

Safety Information

• Operate the device only during the day or in good artificial lighting.
• Read the user manual.
• Wear safety glasses, ear protection, protective gloves, protective clothing, a protective mask, and respiratory protection.
• Do not operate the trimmer without the safety guard.
• Do not start the scythe when there is a bystander nearby.
• Clean the area before starting the work.

Device Usage

1. Insert the extension cord through the back of the arm, making sure that it is always behind the user when cutting.
2. Make sure that the cutting string is not between the cover (9) and the device body.
3. To start the device, press the switch lock and the switch at the same time.
4. Do not mow wet grass. The best mowing results are achieved when the grass is dry.

Changing the Reel

1. Make sure that the switch is in the off position and remove the plug from the socket.
2. Tighten and turn the reel holder, remove the inner cover from the reel, then remove it from the inside and replace it with a new one.
3. Push the reel back into the reel holder and tighten clockwise ensuring it is securely installed.

Cleaning and Maintenance

• Remove any debris or compacted mass from the device before use.
• Keep ventilation slots and motor housing free of dust and dirt. Wipe the device with a clean cloth, brush, or purge with compressed air.
• Clean immediately after every use. Do not use any cleaning agents or solvents to clean the device as they may damage the plastic parts.
• Do not allow water to enter the device.
• Check the condition of the cutting string regularly and tighten screws as necessary. Check bolt tightening after about 2 first hours of operation for new devices.
• Ensure that all components of the power tool are in good working order and do not overload or carry out any work for which the device is not intended.

IMPORTANT INFORMATION

To achieve the highest satisfaction, enjoy the product’s performance and learn about all its features and functions, please read this manual before using the product.
Before using the device, read the Operating Instructions and comply to its contents. The manufacturer shall not be liable for any damage caused by the use of the device other than for its intended purpose or by improper handling.
Keep these Operating Instructions for future reference.

• This device is for domestic use only. Do not use for any other purposes.
• The device should only be connected to an socket with values corresponding to the values on the rating label.
• It is necessary to check, if total current consumption of all devices plugged into the wall outlet does not exceed the fuse in the circuit.
• If you are using an extension cord, make sure that the total power consumption of the equipment plugged into the extension cord does not exceed the extension cord power rating. Extension cords should be arranged in such a way as to avoid tripping hazards.
• Do not let cord hang over edge of counter, or touch any hot surface.
• The device is not designed to be controlled via an external timer, separate remote control, or other equipment that can turn the device on automatically.
• Before maintenance work always disconnect the unit from the power supply.
• When unplugging the power cord from electrical outlet, hold it by the plug only and remove the plug carefully. Never pull the cable as it may cause damage to the plug or power cord. Damage to the power cord or plug can lead to an electrocution hazard.
• Never leave the product connected to the power source without supervision.
• Never put the power cable, the plug or the whole device into the water or any other liquids.
• The device should be cleaned regularly complying with the recommendations described in the section on cleaning and maintenance.
• Do not place the device near sources of heat, flame, an electric heating element or a hot oven. Do not place on any other device.
• The appliance must not be used by children. Keep the appliance and its cord out of the reach of children.
• The appliance may be used by individuals with limited physical, sensory or mental capability as well as those without knowledge of or previous experience in the use of similar appliances, provided such individuals are supervised or instructed with regard to the safe operation of the appliance and are informed about the potential hazards.
• Additional precautions should be taken when using this device in the presence of children or pets. Do not allow children to play with the device.
• Never use the product close to combustibles.
• Never expose the product to atmospheric conditions such as direct sun light or rain, etc… Never use the product in humid conditions (like bathroom or camping house).
• The power cable should be periodically checked for damage. If the power cable is damaged the product should be taken to a professional service location to be fixed or replaced to prevent any hazards from arising.
• Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product by yourself as it can lead to electric shock. Always return the damaged device to a professional service in order to repair it. All the repairs should only be performed by authorized service professionals. Any attempted unauthorised repairs performed can be a hazard to the user.
• Only Original accessories should be used, as well as accessories recommended by the manufacturer. Using accessories which are not recommended by the manufacturer may result in damage of the device and may render the device unsafe for use.
• Keep your workplace tidy and well lit.
• Disorder and insufficient lighting lead to accidents.
• Do not use power tools in explosive atmospheres, i.e. in the presence of flammable liquids, gases or dust.
• A moment of carelessness may cause losing control of your tool.
• If it is possible to fit power tools for dust extraction or collection, check that they are fitted and working correctly. Using such power tools reduces the risk posed by the presence of dust.
• Do not lean out too far when working with your power tool. Maintain a stable posture and balance. This allows you to keep better control of your power tool in unforeseen situations.
• Avoid starting the power tool unintentionally. Make sure the power switch is in the OFF position before connecting the power tool to the mains. Carrying a power tool with your f inger on its trigger or plugging in a power tool after switching it on can lead to accidents.
• Wear appropriate clothing. Do not work in loose clothing and do not wear jewellery while working. Keep your hair, clothing and gloves away from moving parts. The moving parts of a power tool can catch and pull in loose pieces of clothing, jewellery or long hair.
• Remove any spanners or tools from the power tool before starting it. A tool or spanner still connected to the rotating part of the power tool may cause personal injury.
• Be careful when working with power tools, concentrate on your work and use common sense. Do not use a power tool when tired or under the influence of drugs, alcohol or medication. Even a moment of carelessness while working with a power tool can lead to a serious accident.
• Keep children away from the work area and DO NOT allow children to pull on the power cord – this can cause serious injury.
• Before making any adjustments, changing accessories or storing the power tool, move the switch to the off position to disconnect the power tool from the power supply. Such precautions reduce the risk of accidentally starting the power tool.
• Ensure that the vents are free from debris.
• The device may only be used in a dry, well-lit environment.
• This tool should not be used by anyone under the age of 16.

Electrical safety

Connect the device only to an electrical supply of characteristics in accordance with the information on the data plate.
The power tool plugs must match the power sockets. Never alter the power cord plug in any way. Unmodified plugs and suitable electrical sockets reduce the risk of an electric shock. Avoid touching grounded or shorted to ground surfaces such as piping, radiators, radiators and refrigerators. If parts that are grounded or shorted to ground are touched, the risk of electric shock increases.
Do not expose electric devices to rain or humid conditions. If water enters the power tool, the risk of an electric shock increases.
Do not tighten the connection cables. Never use the connection cable to carry, pull electrical equipment or pull the plug out of the socket. Keep the connection cable away from heat sources, oils, sharp edges or moving parts. Damaged or entangled connection cables increase the risk of an electric shock.
Before starting the work, check the power cord before starting the work. Do not operate if the power cord or extension cord is abraded, cut or otherwise damaged. If the power cord is damaged during use, switch off the device and unplug it from the socket.
If the power tool is used outdoors, the connection cables should be extended with waterproof extension cords designed to operate outdoors. Using such an extension cord reduces the risk of an electric shock. The cross-section area of the extension  cord conductors should be at least 1.5 mm when the length of the cable is less than 20 m, and if the length of the cable is
2 between 20 and 50 m, the minimum cross-section is 2.5 mm . A residual current protection device (RCD) must be used as protection against shock from the supply voltage. Using the RCD reduces the risk of electric shock. The equipment should be supplied through an RCD with a rated current not exceeding 30 mA.

General information

The device is intended for house gardening use only as described and protected by these instructions for use After switching off the trimmer, the string/blade rotates for some time. Wait until the motor and the string/blade completely stop before restarting the device. Do not turn the trimmer on or off at short intervals. The operator of the trimmer should wear proper footwear with non-slip soles and long trousers to protect the legs. Do not work barefoot or in flip-flops, sandals. Always use the trimmer holding it with both hands. Operate the device only during the day or in good artificial lighting.

| Read the user manual.| | Use ear protection
---|---|---|---
| General warning| | Wear protective gloves
| Fire hazard| | Wear protective clothing
| Electric shock hazard| | Wear a protective mask
| Wear safety glasses| | Wear respiratory protection

SYMBOLS

• The following symbols may appear in the operating instructions or on the tool’s nameplate.
• These signs contain important information about the product and instructions on how to use it.
• When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2012/19/EU. Please inform yourself about the local separate collection system for electrical and electronic products. Used appliance should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment.
• Do not dispose this appliance in the common waste bin. Your products is designed a manufactured with high quality materials and components, which can be recycled and reused.

Intended use:
The gardening tool is designed for home use, for trimming grass and weeds, usually in areas that cannot be reached with a lawnmower. The gardening tool is not intended for commercial or industrial use.

Before starting the device:
Check the technical condition of the device and make sure that none of the components are damaged and that the reel with the string or the blade is properly installed and fastened.
Before using the trimmer, check that there are no signs of wear or damage and, if necessary, return it to an authorised service centre.
Check that bystanders and animals are at a safe distance from the trimmer’s workplace (at least 15 meters).
The trimmer should be disconnected from the power supply in the event of breaks in work, before moving it to another workplace, and before any work on the power tool (e.g. setting or cleaning) .

WEAR PERSONAL PROTECTIVE EQUIPMENT

• Wear safety glasses according to En166
• Use protective masks in accordance with En149
• Use other types of proper personal protective equipment, depending on the type of work involved.

Device description

1. Switch
2. Main handle
3. Middle tube
4. Motor housing
5. Bracket
6. Reel
7. Reel cover
8. Safety guard
9. Power cord
10. Cord holder
11. Additional handle 12 Mounting screws

Device assembly:
Connect the upper part to the centre tube holder and screw the screw into place. Connect the middle part to the motor housing bracket and screw the screw into place.

Safety guard installation:
Do not operate the trimmer without the safety guard

To install the safety guard
Tighten the partially loosened screws securing the head (11) to the head housing. Install the guard (9) on the head housing so that the housing latch (9) snaps in.
Make sure that the cutting string is not between the cover (9) and the device body. Attach the cover (9) using the loosened cover mounting screws (11).

To start the device:
Press the switch lock and the switch at the same time Remember not to start the scythe when there is an bystander nearby. Clean the area before starting the work.

Changing the reel:

1. Make sure that the switch is in the off position, remove the plug from the socket.
2. Tighten and turn the reel holder, remove the inner cover from the reel, then remove it from the inside and replace it with a new one.
3. Push the reel back into the reel holder and tighten clockwise ensuring it is securely installed.

GRASS mowing:
Do not mow wet grass. The best mowing results are achieved when the grass is dry. Insert the extension cord through the back of the arm, making sure that it is always behind the user when cutting. Keep the device tilted at an angle of 20 degrees to the grass being mowed, moving it in a pendulum motion, to the left and right. Make sure to keep the device away from yourself – see figure.

Effective mowing of the grass with the device is possible only if the grass not higher than 15 cm. Keep the grass trimmer away from hard objects. When the string or blade comes into contact with a hard object, the string or blade may break. Stones can be thrown away and hit the surrounding objects at high speed causing damage. It is prohibited to use the device without a safety cover.
When using the trimmer, remember to maintain proper body posture during work.

MOWING AROUND SHRUBS AND TREES

When mowing grass and weeds around shrubs and trees be extremely careful and do not allow them to come into contact with the rotating string or blade. Damage to the bark may result in the death of the tree or shrub .

String ejection:
If the string is too short, pull it out. The unit is equipped with an automatic dispense head. Press the reel lightly against the ground to eject the string automatically.
During this operation, please note that pressing the reel too hard or too hard against the ground may cause damage to the reel, so it is recommended to do it manually to prevent damage.

Cleaning and maintenance

1. After each use clean the entire device of plant residues and the lower cover of the collected compacted mass.

2. Ventilation slots and motor housing should be kept free of dust and dirt, as much as possible. Wipe the device with a clean cloth, brush or purge with compressed air.

3. It is recommended to clean immediately after every use.

4. Do not use any cleaning agents or solvents to clean the device; they may damage the plastic parts. Take care not to allow water to enter the device.

5. Check the condition of the cutting string regularly, as well as the
   tightening of the screws. With new devices, the bolt tightening should be checked after about 2 first hours of operation. Tighten the loosened bolts if necessary.

6. Ensure that all components of the power tool are in good working order and do not overload or carry out any work for which the device is not intended

Grass trimmer

• Power: 250W
• Voltage: 230-240V~, 50Hz
• Rotational speed: 12000/min
• Cutting diameter: 22 cm
• String diameter: 1.2 mm

Double string

• Cord length: 35 cm
• Head type: semi-automatic
• Noise and vibrations.

The noise and vibrations have been measured in accordance with 2000/14/EC,Annex VI,2005/88/EC Noise emission: Sound pressure level (LpA): 81.20 dB (A)

• KpA deviation: 3.00 dB (A)
• Measured sound power level LwA: 93.70 dB (A)
• KwA deviation: 1.89 dB (A)
• Guaranteed sound power level: LwA: 96.00 dB (A)
• Total vibration value and measurement uncertainty (K):
• The value of vibrations acting on the upper limbs: 5.62 m/s² , k= 1.50 m/s²

The declared total vibration value has been measured according to the standard test method and can be used to compare one device to another. The given vibration emission value may be used for the preliminary estimation of the negative impact.
After every 15 minutes of work allow 15 minutes break.

EU – DECLARATION OF CONFORMITY

01/2022/GB0l0
MANUFACTURER:
BLAUPUNKT COMPETENCE CENTER
2N-Everpol Sp. z o.o.
ul. Pulawska 403A
02-801 Warsaw, Poland
Authorized person to prepare the technical documentation:
Tomasz Jak6bczyk
ul. Putawska 403A
02-801 Warsaw, Poland
We declare under our sole responsibility that our product:

• Type of device:  Grass trimmer
• Name:  GT3010

If used for its intended use complies with the essential protection requirements relating to the:
2014/30/EU (EMC Directive)
2014/35/EU (LVD Directive)
2006/42/EC (MD Machinery Directive)
2011/65/EU (RoHS Directive) and its Annex II amending directive 2015/863/EU
The assessment of this product has been based on the following standards:

EMC standards·
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+Al:2019
EN 55014-1:2017+Al:2020
EN 55014-2:2015

MD and LVD standards:
EN 60335-1 :2012+Al 1:2014+A13 :2017+Al: 2019+Al4 :2019+A2 :2019+Al5 :2021 EN 50636-2-91:2014
EN 62233:2008

RoHS standards:
EN IEC 63000:2018

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>