MICROCHIP PDS-204GCO/AC Outdoor 4 Port BT PoE Switch 2 SFP Uplink Port Hardware Installation Guide

PDS-204GCO/AC Outdoor 4 Port BT PoE Switch 2 SFP Uplink Port Hardware

Product Information

PDS-204GCO/ACTM Outdoor 4 Port BT PoE Switch + 2 SFP Uplink Port The PDS- 204GCO/ACTM is an outdoor switch with four Power over Ethernet (PoE) ports and two Small Form-factor Pluggable (SFP) uplink ports. The switch is designed for outdoor use and is equipped with IP67-rated weather protection to withstand harsh weather conditions. The PoE ports provide power to PoE-enabled devices, such as wireless access points, IP cameras, and VoIP phones, eliminating the need for separate power cables. The SFP uplink ports provide high-speed connectivity to other network devices.

Hardware Description

The switch has the following hardware features:

• Four PoE ports
• Two SFP uplink ports
• IP67-rated weather protection
• Power input voltage range: 48V DC to 56V DC
• Power consumption: maximum 60W

Mechanical View

The switch has a compact and sturdy metal enclosure with mounting brackets for wall and pole installations. The dimensions of the switch are 205mm x 130mm x 44mm (WxDxH).

Installation

Before installation, ensure that you have read and understood the safety instructions provided in the user manual.

Wall Installation

1. Choose a suitable location for the switch that is protected from direct sunlight and rain.
2. Attach the mounting brackets to the switch using the screws provided.
3. Use the screws and wall anchors provided to attach the switch to the wall.

Pole Mounting Installation

1. Choose a suitable location for the switch on the pole that is protected from direct sunlight and rain.
2. Attach the mounting brackets to the switch using the screws provided.
3. Use the stainless steel straps provided to attach the switch to the pole.

Connecting Gigabit Ethernet Cable

1. Connect one end of the Ethernet cable to one of the PoE ports on the switch.
2. Connect the other end of the Ethernet cable to the PoE-enabled device.

Connecting Fiber Optic Cable

1. Insert one end of the SFP module into one of the SFP uplink ports on the switch.
2. Insert the other end of the SFP module into the SFP slot of the fiber optic transceiver.
3. Connect one end of the fiber optic cable to the fiber optic transceiver.
4. Connect the other end of the fiber optic cable to another network device, such as a switch or router.

Connecting Power Cable

1. Connect one end of the power cable to the power input port on the switch.
2. Connect the other end of the power cable to a power source that supplies 48V DC to 56V DC.

Troubleshooting

The user manual provides an Appendix B with troubleshooting tips for common issues that may occur during installation or operation of the switch.

Specifications

The user manual provides an Appendix C with the specifications for the switch, including details on the hardware, power consumption, and environmental conditions.

Standards

The user manual provides an Appendix D with information on the standards and regulations that the switch complies with, including FCC and CE regulations.

Recycling and Disposal

The user manual provides an Appendix E with information on how to recycle and dispose of the switch in an environmentally responsible manner.

Ordering Information

The user manual provides an ordering information section with details on how to order replacement parts or additional switches.

References

The user manual provides a references section with a list of documents and resources for further information on the switch.

Revision History

The user manual provides a revision history section with details on the changes made to the manual over time.

Introduction

Microchip’s PDS-204GCO™ switch is a 4 + 2 ports outdoor PoE switch. It can provide power and data connectivity for four powered devices and connect them to the network through data uplink ports. The PDS-204GCO switch can be remotely managed through the web or SNMP, allowing monitoring and control of the device and its ports. The PDS-204GCO switch supports 10/100/1000 Mbps data rates on the RJ45 Gigabit ports and 100/1000/2500 Mbps on the SFP ports. It is powered through wide-range AC input (100 VAC–240 VAC). The PDS-204GCO switch is IP66/IP67 rated and has an extended temperature range. Therefore, it can be installed in an outdoor environment. In a typical installation, the PDS-204GCO switch provides power to four outdoor devices, such as WLAN AP, WLAN Mesh, IP Camera, and so on.

Audience

This guide is designed for personnel who install and maintain the switch. These persons must be familiar with electronic circuitry and wiring practices, and qualified and experienced electronic or electromechanical technicians.

Hardware Description

This switch provides two SFP ports for uplink and four GE copper PoE ports for downstream connectivity. The PDS-204GCO switch can be either wall or pole mounted.

The PDS-204GCO switch provides the following hardware features:

• Two SFP ports 100/1000/2500Base-X
• Four copper PoE 10/100/1000BASE-T ports
• Up to 90W PoE copper per port
• Maximum total power 152W
• Management Ethernet port (any of the ports can be used as Management)
• Fan-less passively cooled design
• AC input
• IP66/IP67 enclosure
• Four Copper cable glands
• Two fiber cable glands + cable gland extender
• Six ports cable gland caps
• Mechanical mounting kit—enables pole mounting (including with unit)

Mechanical View

The following figures show the mechanical view of the PDS-204GCO switch. Figure 2-1. Mechanical View

Installation

This section describes the installation process of the PDS-204GCO switch.

CAUTION: Ensure the following before mounting the PDS-204GCO switch to a fixed location:

• Weather-proof connection is present. To meet IEC60529 level IP66/IP67, the PDS-204GCO AC power plug must be connected to a weather-proof AC power source box.
• There is no ON or OFF switch; plug the PDS-204GCO switch into an AC main power source.
• PDS-204GCO AC power lines must be connected to the socket-outlet. This socket-outlet must be installed near the equipment and must be easily accessible.

WARNING

PDS-204GCO unit must be connected to earth grounding using a customer-supplied ground wire before power is applied.

Wall Installation

The PDS-204GCO unit can be mounted on a wall/bench (all kinds of flat surfaces: wood, brick, concrete, and so on) using the mounting holes.
Fasten the PDS-204GCO using four screws, as shown in the following figure.
Figure 3-1. Wall Mounting

Pole Mounting Installation

The following table lists the kit details supplied with the product.
Table 3-1. PDS-204GCO Kit Details

Perform the following steps for pole mounting installation.

1. Attach the pole bracket to the switch using four pan head screws and tighten the pan head screws to 1.1 Nm.
2. The unit must be installed with DATA IN, and DATA & PWR OUT ports facing down, as shown in the following figures. Dimensions of support Pole diameter: 60 mm to 200 mm (2.5 inches to 8 inches)
   Table 3-2. Installation of Units on Pole

Connecting Network Cables

This section describes how to connect the following PDS-204GCO interfaces.

Connecting Gigabit Ethernet Cable
Perform the following steps to connect the Gigabit Ethernet cable.

1. Remove the metal gland from the PDS-204GCO unit by turning it counterclockwise. Keep the dust cap for future use.
2. Insert the cable through metal gland, rubber seal, and pressure fingers and plug into the port number 1.
3. Secure all glands till the rubber gasket is tightly closed around the cable.
4. Ethernet cable
5. Metal gland
6. Rubber seal
7. Pressure fingers

Notes:

• For easier installation, start with port number 1 assembly (Data & PWR 1), and then connect the Uplink port.
• Use cable Cat 5e or above outdoor grade.
• Secure the gland until the rubber gasket is firmly closed around the cable.
• The PDS-204GCO switch is not shipped with Ethernet cable and RJ45 male connectors.

Connecting Fiber Optic Cable

Figure 4-1. Connecting Fiber Optic Cable

1. Remove the metal gland from the PDS-204GCO unit by turning it counterclockwise. Keep the dust cap for future use.
2. Insert the cable through metal gland, rubber seal, and pressure fingers and plug into the Uplink port.
3. Secure the gland until the rubber gasket is firmly closed around the cable.

Note: SFP cord must be outdoor use grade.

Connecting Power Cable

The following table lists the AC power cable specifications.
Table 5-1. AC Power Cable Specifications

Worldwide—H05RN-F or H07RN-F

Voltage rating| 300V (or better recommended)
Temperature range| −40 ℃ to 65 ℃ (or better recommended)
Cable size| 16 AWG–18 AWG 3C

1.0 mm2–1.5 mm2 3C

Cable outer dimension| Diameter: 3/16 in.–3/8 in.

Diameter: 5.0 mm–9.5 mm

Approved for indoor and outdoor applications.

The following figures show how to connect the power connector. Figure 5-1. Connecting AC Connect or

Figure 5-2. AC Connector Assembly

Appendix A: Safety and Warnings

The following sections describe safety information and warnings.

Safety Information

• Installation and removal of the PDS-204GCO unit must be carried out by qualified personnel only.
• The PDS-204GCO DATA PWR OUT ports are shielded RJ45 data sockets. They cannot be used as Plain Old Telephone Service (POTS) sockets. Only RJ45 data connectors can be connected to these sockets.
• Follow basic electricity safety measures while connecting the PDS-204GCO unit to its power source.
•  A voltage mismatch can cause equipment damage and might pose a fire hazard. If the voltage indicated on the label is different from the power outlet voltage, do not connect the PDS-204GCO to this power outlet.
• All wiring and connections must be in accordance with NFPA 70 (NEC).
• This product is not intended to become a permanent part of the building structure.
• Power supply cord must not be attached to the building surface or run through walls, ceilings, floors, and similar openings in the building structure.
• Measures must be taken to prevent physical damage to the power supply cord, including proper routing.

Warnings

• Do not use a cross-over cable between the PDS-204GCO output port and the load device.
• Take extra care when connecting the AC power, so that “N”, “L”, and “Ground”, are connected to the proper polarity.
• Ensure that the AC power is within the allowed range.

Appendix B: Troubleshooting

Table 7-1. Troubleshooting Symptoms and Solutions

2.         Verify that the voltage at the power inlet is between 100 VAC–240 VAC.

3.         Remove and re-apply power to the device.

PD does not operate| 1.  Verify that the unit detects a PD.

2.  Verify that the PD is designed for PoE operation.

3.  Verify that a standard Category 5/5e/6 cable is in use – Straight wired cable, with four pairs.

4.  If an external power splitter is in use, replace it with a splitter known to be in good condition.

5.  Ensure that the input Ethernet cable is connected to the Up-link port.

6.  Verify that the PD is connected to the Data & Power port.

7.  Try reconnecting the same PD to a different PoE switch. If it works, then there is probably a faulty port or faulty RJ45 connection.

8.  Verify that there is no short-circuit over any of the twisted pair cables or over the RJ45 connectors.

The end device operates, but there is no data link| 1.  Verify that the port indicator on the unit GUI (Wed page) is continuously lit.

2.  If an external power splitter is in use, then replace it with a splitter known to be in good condition.

3.  Verify that for this link, you are using standard UTP/FTP Category 5 straight (non-crossover) cabling, with all four pairs.

4.  Verify that the Ethernet cable length is less than 100 meters from Ethernet source to the remote terminal.

5.  Try to reconnect the same PD to a different PoE switch. If it works, then there is probably a faulty port or faulty RJ45 connection.

Appendix C: Specifications

The following table lists the environmental specifications. Table 8-1. Environmental Specifications

−40 ℃ to 60 ℃ for 90W

(−40 ℉ to 140 ℉)

| 10% to 90% (no condensation allowed)
Storage| −40 to 85 ℃

(−40 ℉ to 185 ℉)

| 5% to 95%

The following table lists the electrical specifications. Table 8-2. Electrical Specifications

Input Current

(100 VAC–240 VAC)

| 2.5A (max.)
Available Output Power (max.)| 152W
Nominal Output Voltage| 55 VDC

The following table lists the specifications of the interface. Table 8-3. Interface

Uplink

PDS-204GCO:

•       1000BASE-X

•       2500BASE-X

•       100BASE-FX

| SFP cage
Output (DATA PWR OUT)| RJ45 female socket, with DC voltage
AC Power IN| 3 Pins AC power in—Line, Neutral, and Earth Ground.

Appendix D: Standards

PDS-204 EMC Compliance

• CE:
  • EN55035, EN61000-4-5 Class 5 (6KV on AC in)
  • EN55032 class B
• FCC Part 15 class B
• VCCI

PDS-204 Safety Compliance

• UL/EN/IEC 62368-1
• UL60950-22
•  D-Mark

PDS-204 Lightning Protection
Designed to meet GR-1089-CORE (issue 4) lightning protection requirements.

Other Standards and Approvals

• IEEE® 802.3bt (PoE) standards
• RoHS compliant
• WEEE compliant
• REACH compliant
• Dust and water intrusion
  • IEC60529, level IP66/IP67
  • NEMA 250, level 4x

Appendix E: Recycling and Disposal

This section provides disposal instructions for old products. The WEEE (Waste Electrical and Electronic Equipment) national environmental initiatives have been put in place to ensure that products are recycled using best available treatment, recovery, and recycling techniques to ensure human health and high environmental protection. Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Do not dispose of your old product in your general Household waste bin. Inform yourself about the local separate collection system for electrical and electronic products marked by the following symbol.

Use one of the following disposal options:

• Dispose the complete product (including its cables, plugs, and accessories) in the designated WEEE collection facilities.
• If you purchase a replacement product, hand your complete old product back to the retailer. He must accept it, as required by the national WEEE legislation.

Ordering Information

References

For additional information, see the following related documents:

• Microchip Getting Started With PDS204GCO™ Switch Configuration User Guide
• Microchip PDS-204GCO™ Web Management User Guide
• Microchip PDS-204GCO™ Command Line Interface (CLI) User Guide

Revision History

The revision history describes the changes that were implemented in the document. The changes are listed by revision, starting with the most current publication.

Microchip Information

Microchip provides online support via our website at www.microchip.com/. This website is used to make files and information easily available to customers. Some of the content available includes:

• Product Support: Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software
• General Technical Support: Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip design partner program member listing
• Business of Microchip: Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives

Product Change Notification Service

Microchip’s product change notification service helps keep customers current on Microchip products. Subscribers will receive email notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest.
To register, go to www.microchip.com/pcn and follow the registration instructions.

Customer Support

Users of Microchip products can receive assistance through several channels:

• Distributor or Representative
•  Local Sales Office
• Embedded Solutions Engineer (ESE)
• Technical Support

Customers should contact their distributor, representative or ESE for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in this document. Technical support is available through the website at: www.microchip.com/support

Microchip Devices Code Protection Feature

Note the following details of the code protection feature on Microchip products:

• Microchip products meet the specifications contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and under normal conditions.
• Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not mean that we are guaranteeing the product is “unbreakable”. Code protection is constantly evolving. Microchip is committed to continuously improving the code protection features of our products.

Legal Notice

This publication and the information herein may be used only with Microchip products, including to design, test, and integrate Microchip products with your application. Use of this information in any other manner violates these terms. Information regarding device applications is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. Contact your local Microchip sales office for additional support or, obtain additional support at www.microchip.com/en-us/support/design-help/client-support- services.
THIS INFORMATION IS PROVIDED BY MICROCHIP “AS IS”. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, OR WARRANTIES RELATED TO ITS CONDITION, QUALITY, OR PERFORMANCE. IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE INFORMATION OR ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP’S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THE INFORMATION.
Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated.

Trademarks

The Microchip name and logo, the Microchip logo, Adaptec, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AgileSwitch, APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, Flashtec, Hyper Speed Control, HyperLight Load, Libero, motorBench, mTouch, Powermite 3, Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet- Wire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub, TimePictra, TimeProvider, TrueTime, and ZL are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky, BodyCom, Clockstudio, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, Espresso T1S, EtherGREEN, GridTime, IdealBridge, In-Circuit Serial Programming, ICSP, INICnet, Intelligent Paralleling, IntelliMOS, Inter-Chip Connectivity, JitterBlocker, Knob-on- Display, KoD, maxCrypto, maxView, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, RTAX, RTG4, SAM-ICE, Serial Quad I/O, simpleMAP, SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI, SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total Endurance, Trusted Time, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY, ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. The Adaptec logo, Frequency on Demand, Silicon Storage Technology, and Symmcom are registered trademarks of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. 2022, Microchip Technology Incorporated and its subsidiaries. All Rights Reserved.

Quality Management System

For information regarding Microchip’s Quality Management Systems, please visit www.microchip.com/quality.

Worldwide Sales and Service

Corporate Office

2355 West Chandler Blvd. Chandler, AZ 85224-6199

Tel: 480-792-7200

Fax: 480-792-7277

Technical Support: www.microchip.com/support Web Address: www.microchip.com Atlanta

Duluth, GA

Tel: 678-957-9614

Fax: 678-957-1455

Austin, TX

Tel: 512-257-3370

Boston Westborough, MA Tel: 774-760-0087

Fax: 774-760-0088

Chicago

Itasca, IL

Tel: 630-285-0071

Fax: 630-285-0075

Dallas

Addison, TX

Tel: 972-818-7423

Fax: 972-818-2924

Detroit

Novi, MI

Tel: 248-848-4000

Houston, TX

Tel: 281-894-5983

Indianapolis Noblesville, IN Tel: 317-773-8323

Fax: 317-773-5453

Tel: 317-536-2380

Los Angeles Mission Viejo, CA Tel: 949-462-9523

Fax: 949-462-9608

Tel: 951-273-7800

Raleigh, NC

Tel: 919-844-7510

New York, NY

Tel: 631-435-6000

San Jose, CA

Tel: 408-735-9110

Tel: 408-436-4270

Canada – Toronto

Tel: 905-695-1980

Fax: 905-695-2078

| Australia – Sydney

Tel: 61-2-9868-6733

China – Beijing

Tel: 86-10-8569-7000

China – Chengdu

Tel: 86-28-8665-5511

China – Chongqing

Tel: 86-23-8980-9588

China – Dongguan

Tel: 86-769-8702-9880

China – Guangzhou

Tel: 86-20-8755-8029

China – Hangzhou

Tel: 86-571-8792-8115

China – Hong Kong SAR

Tel: 852-2943-5100

China – Nanjing

Tel: 86-25-8473-2460

China – Qingdao

Tel: 86-532-8502-7355

China – Shanghai

Tel: 86-21-3326-8000

China – Shenyang

Tel: 86-24-2334-2829

China – Shenzhen

Tel: 86-755-8864-2200

China – Suzhou

Tel: 86-186-6233-1526

China – Wuhan

Tel: 86-27-5980-5300

China – Xian

Tel: 86-29-8833-7252

China – Xiamen

Tel: 86-592-2388138

China – Zhuhai

Tel: 86-756-3210040

| India – Bangalore

Tel: 91-80-3090-4444

India – New Delhi

Tel: 91-11-4160-8631

India – Pune

Tel: 91-20-4121-0141

Japan – Osaka

Tel: 81-6-6152-7160

Japan – Tokyo

Tel: 81-3-6880- 3770

Korea – Daegu

Tel: 82-53-744-4301

Korea – Seoul

Tel: 82-2-554-7200

Malaysia – Kuala Lumpur

Tel: 60-3-7651-7906

Malaysia – Penang

Tel: 60-4-227-8870

Philippines – Manila

Tel: 63-2-634-9065

Singapore

Tel: 65-6334-8870

Taiwan – Hsin Chu

Tel: 886-3-577-8366

Taiwan – Kaohsiung

Tel: 886-7-213-7830

Taiwan – Taipei

Tel: 886-2-2508-8600

Thailand – Bangkok

Tel: 66-2-694-1351

Vietnam – Ho Chi Minh

Tel: 84-28-5448-2100

| Austria – Wels

Tel: 43-7242-2244-39

Fax: 43-7242-2244-393

Denmark – Copenhagen

Tel: 45-4485-5910

Fax: 45-4485-2829

Finland – Espoo

Tel: 358-9-4520-820

France – Paris

Tel: 33-1-69-53-63-20

Fax: 33-1-69-30-90-79

Germany – Garching

Tel: 49-8931-9700

Germany – Haan

Tel: 49-2129-3766400

Germany – Heilbronn

Tel: 49-7131-72400

Germany – Karlsruhe

Tel: 49-721-625370

Germany – Munich

Tel: 49-89-627-144-0

Fax: 49-89-627-144-44

Germany – Rosenheim

Tel: 49-8031-354-560

Israel – Ra’anana

Tel: 972-9-744-7705

Italy – Milan

Tel: 39-0331-742611

Fax: 39-0331-466781

Italy – Padova

Tel: 39-049-7625286

Netherlands – Drunen

Tel: 31-416-690399

Fax: 31-416-690340

Norway – Trondheim

Tel: 47-72884388

Poland – Warsaw

Tel: 48-22-3325737

Romania – Bucharest

Tel: 40-21-407-87-50

Spain – Madrid

Tel: 34-91-708-08-90

Fax: 34-91-708-08-91

Sweden – Gothenberg

Tel: 46-31-704-60-40

Sweden – Stockholm

Tel: 46-8-5090-4654

UK – Wokingham

Tel: 44-118-921-5800

Fax: 44-118-921-5820

References

• {波多野42部无码喷潮在线,18禁美女裸身无遮挡免费网站,国产成人精品一区二三区在线观看,久久精品国产亚洲AⅤ无码}
• Empowering Innovation | Microchip Technology
• Empowering Innovation | Microchip Technology
• Microchip Lightning Support
• Empowering Innovation | Microchip Technology
• Empowering Innovation | Microchip Technology

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>