TOOLOTS CH7090-TD2 Up-Sliding Pneumatic Heat Press Machine with Double-Station User Manual
- October 30, 2023
- TOOLOTS
Table of Contents
TOOLOTS CH7090-TD2 Up-Sliding Pneumatic Heat Press Machine with Double-
Station
OVERVIEW
Specification Details
Platen Size (CM)| Platen Size (Inches)| Voltage (V)| Power (KW)| Time Range
(Sec)| Temperature Range ()| Pressure (Mpa.)
---|---|---|---|---|---|---
40 x 40| 16 x 16| 110| 2.5| 0-999| 0-299| 0.8
40 x 50| 16 x 20| 110| 3| 0-999| 0-299| 0.8
40 x 60| 16 x 24| 110| 3.8| 0-999| 0-299| 0.8
50 x 70| 20 x 28| 220/380| 4| 0-999| 0-299| 0.8
60 x 80| 24 x 32| 220/380| 6| 0-999| 0-299| 0.8
70 x 90| 28 x 35| 220/380| 8| 0-999| 0-299| 0.8
80 x 100| 32 x 39| 220/380| 9| 0-999| 0-299| 0.8
The Main Purpose
The Up-sliding Pneumatic Heat Press Machine with Double-station is suitable for fusing low temperature and low pressure lining and fabrics of various types of clothing. It can also be used to heat transfer colorful patterns and texts of sublimation and solvent inks, and for hot stamping on cotton, linen, chemical fiber, and other fabrics. Additionally, it can be used for heat treatment by flocking heat transfer and foam printing processes on cotton, hemp, chemical fiber, nylon fabric, and ceramic products.
Operation Steps
- Connect the compressor connector, open the air pressure, adjust the pressure gauge (0.4Mpa-0.6Mpa), and raise the heating plate.
- Connect the air switch, turn on the main power switch, and the indicator light will turn on.
- Adjust the required time and temperature, and wait for the machine to heat up.
- After heating, temperature meter OUT1 light off, automatic flashing (insulation), start the test, clothes flat on the silicone mat, adjust to manual, press the start switch, flatten the article, put in the colorful patterns (pay attention to the front and back of colorful patterns), and then put high-temperature cloth. Press the start switch, hot stamping will begin.
- When the set time is finished, the heating plate will be raised automatically, and the machine head will be moved to another working table.
- According to the test printing effect, adjust the machine to the best effect.
- After the successful test printing, the transfer switch can be changed to automatic transmission. After placing the hot stamping items, as long as the handle is moved to the top of the hot stamping items, hot stamping will automatically start. In case of an emergency, press the emergency stop button. At this time, the upper pressing plate (heating plate) will automatically rise, and the emergency stop button can be reset to continue hot stamping.
Repair Items
-
Pressure: if the distance between the four sides of the heating plate and the four sides of the bottom plate is not uniform, first use a ruler to measure whether the distance between the four sides of the heating plate and the four sides of the bottom plate is consistent. If it is inconsistent, adjust the screw down nut in the center of the heating plate.
-
If the pressure is too high or too low (usually 0.4Mpa-0.6Mpa), adjust the filter. The upper regulating valve is lifted in the + direction to increase the pressure, – to reduce the pressure, or check whether the pressure of the air compressor is normal (usually the pressure of the air compressor is (0.6Mpa0.8Mpa).
-
Time: when the machine head is in place and there is no countdown, check the proximity switch, whether the distance is appropriate, and adjust it to less than 0.197 (5mm). When time is up, the heating plate does not press down, check the circuit (Solid state relay).
-
Temperature: adjust to the set temperature, no temperature rise, not emperature control, check whether the temperature control table, solid state relay, heating plate circuit is in good contact and the fault of electrical
components. -
Heating plate regulating valve: the rising speed of heating plate can be adjusted at will
Note
The whole machine must have suitable and reliable protective ground wire
Successful hot stamping needs to have the right time, temperature and
pressure, the thickness and materials of clothing and all kinds of hot
stamping paper affect the effect of hot stamping, all kinds of hot
stampingpaper need to try hot sample before mass production.
The required temperature and time for hot stamping are as follows(forreference only)
- Cotton clothing: 180 degrees, 15 seconds
- Polyester clothing: 180-220 degrees, 25 seconds
- Pearl plate : 180 degrees, 120–180 seconds
- Metal pendant : 180 degrees, 60 seconds
- Mouse pad: 180 degrees, 15 seconds
- Porcelain plate: 200 degrees, 180 seconds
After-sales Service
Thank you for buying our products. Our company has made great efforts in
machine production, technical research and after-sales service for many years.
We promise you with high quality products:
- The machine is guaranteed for one year. During one-year service period, the machine occurs the non-human fault, our company is responsible for free repair and send accessories.
- If the machine is damaged or malfunctioned due to customers’ failure to install the machine as required or improper operation, maintenance or transportation, our company will be responsible for repair and technical guidance, and only the spare parts cost will be charged.
- If the machine breaks down after one-year warranty period, our companywillbe responsibleformaintenanceand onlychargethe spare parts cost.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>