MICROCHIP SM48DB Silicon Sculptor 4 Conformance Test Instruction Manual

MICROCHIP SM48DB Silicon Sculptor 4 Conformance Test

Product Information

Silicon Sculptor 4 Conformance Test Instructions

Specifications

• Model: Silicon Sculptor 4 (SS4)
• Hardware Compatibility: SM48D or SM48DB Socket Module
• Software: SculptW Software
• Power Supply: Required
• Connection: USB cable

Product Usage Instructions

Setup Instructions

1. Place SM48D or SM48DB onto the SS4 programmer.
2. Connect the SS4 programmer to the PC using a USB cable.
3. Connect the power supply to the programmer and power outlet.
4. Install the latest version of the SculptW software on your computer if not installed.
5. Launch the SculptW software after connecting all hardware components.

Test Instructions

1. Click the Device menu in the software, type ‘BP’ in the Look for box, and select ‘BP Microsystems SS4 Certificate of Conformance Test’.
2. Follow the on-screen instructions to start the test.

High Voltage Test

1. Connect the voltmeter probes to pins 1 and 48.
2. Measure the voltage of pin 1 and ensure it falls within the specified range.

Low Voltage Test

1. Measure the voltage of pin 1 and verify if it is within the specified range.

Low-Frequency Test

1. Connect the scope probe to pin 1 and ground to pin 48.
2. Set the probe voltage of the oscilloscope to 2 V/Div and adjust timing to observe an entire wave period.
3. Measure the frequency of one period of the waveform and check if it is within the specified range.

FAQ (Frequently Asked Questions)

Q: What should I do if the programmer fails to turn on during setup?
A: Close the software, check USB and power connections, and attempt to power up the programmer again.

Q: How do I know if the programmer requires service during testing?
A: If voltage or frequency readings fall outside of the specified range during tests, it indicates that the programmer may be out of calibration and requires service.

Introduction

This document provides detailed instructions on the Silicon Sculptor 4 (SS4) conformance test.

Required Hardware
The following is the list of required hardware for the conformance test:

• SS4 to be tested
• SM48D or SM48DB socket module
• Voltmeter
• Oscilloscope

The following figure shows the location of pins 1 and 48 of the SM48D/SM48DB socket module. These pins are used to perform the actual voltage and waveform measurements.

Figure 1. SM48D/SM48DB Socket Module

Setup Instructions

To setup the unit, perform the following steps:

1. Place SM48D or SM48DB onto the SS4 programmer as shown in the following figure.
   Figure 2. SM48D/SM48DB Socket Module Placed on SS4 Programmer

2. Connect the SS4 programmer to the PC using a USB cable.

3. Connect the power supply to the programmer and power outlet.
   Note: Ensure that the power for the programmer is still turned off.

4. Install the latest version of the SculptW software on your computer, if not installed.

5. Launch the SculptW software. The programmer must be powered after this step. Ensure that the green LED illuminates after powering up the system. If the programmer fails to turn on, then close the software, check the USB and power connections, and attempt to power up the programmer again.

The following figure shows SculptW software.

Test Instructions

To start the test, perform the following steps:

1. Click the Device menu, then in the Look for box, type BP as shown in the following figure.
2. Click BP Microsystems SS4 Certificate of Conformance Test, and then click Select.
3. The following window then appears explaining how to run the test. Press Enter to close this window.
4. Click Execute to start the test.

High Voltage Test
To conduct the high voltage test, perform the following steps:

1. Connect the voltmeter probes to pins 1 and 48.
2. Measure the voltage of the pin 1 as shown in the following figure. Check if the voltage reading is within the specified range. If the voltage readings fall outside of the specified range, it indicates that the programmer is out of calibration and requires service. The following figure shows voltage measurement of the pin 1.
3. Press Start to move on to the next test.

Low Voltage Test

To conduct the low voltage test, perform the following steps:

1. Measure the voltage of the pin 1 as shown in the following figure. Check if the voltage reading is within the specified range. If the voltage readings fall outside of the specified range, it indicates that the programmer is out of calibration and requires service.
2. Press Start to move on to the next test.

Low Frequency Test
To conduct the low frequency test, perform the following steps:

1. Connect the scope probe to pin 1 and ground to pin 48.
2. Set the probe voltage of the oscilloscope to 2 V/Div.
3. Adjust the timing to see an entire wave period as shown in the following figure.
4. Measure the frequency of one period of the wave form. Check if the frequency reading is within the specified range. If the measured frequency falls outside of the specified range, it indicates that the programmer is out of calibration and requires service.
5. Press Start to move on to the next test.

Pulse Width Test
To conduct the pulse width test, perform the following steps:

1. Set the trigger of the oscilloscope to capture the signal on the rising edge of the signal.
2. Measure the pulse width. Check if the pulse width reading is within the specified range. If the measured pulse width falls outside of the specified range, it indicates that the programmer is out of calibration and requires service. The following figure shows the expected result of pulse width test.
3. Press Start to terminate the test.

Microchip Information

The Microchip Website
Microchip provides online support via our website at www.microchip.com/. This website is used to make files and information easily available to customers. Some of the content available includes:

• Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software
• General Technical Support – Frequently Asked Questions (FAQs), technical support requests,online discussion groups, Microchip design partner program member listing
• Business of Microchip – Product selector and ordering guides, latest Microchip press releases,listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives

Product Change Notification Service
Microchip’s product change notification service helps keep customers current on Microchip products. Subscribers will receive email notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest.

To register, go to www.microchip.com/pcn and follow the registration instructions.

Customer Support
Users of Microchip products can receive assistance through several channels:

• Distributor or Representative
• Local Sales Office
• Embedded Solutions Engineer (ESE)
• Technical Support

Customers should contact their distributor, representative or ESE for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in this document.
Technical support is available through the website at: www.microchip.com/support

Microchip Devices Code Protection Feature
Note the following details of the code protection feature on Microchip products:

• Microchip products meet the specifications contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and under normal conditions.
• Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not mean that we are guaranteeing the product is “unbreakable”.

Code protection is constantly evolving. Microchip is committed to continuously improving the code protection features of our products.

Legal Notice
This publication and the information herein may be used only with Microchip products, including to design, test, and integrate Microchip products with your application. Use of this information in any other manner violates these terms. Information regarding device applications is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. Contact your local Microchip sales office for additional support or, obtain additional support at www.microchip.com/en-us/support/design- help/
client-support-services.

THIS INFORMATION IS PROVIDED BY MICROCHIP “AS IS”. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, OR WARRANTIES RELATED TO ITS CONDITION, QUALITY, OR PERFORMANCE.

IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE INFORMATION OR ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW,MICROCHIP’S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THE INFORMATION.

Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk,and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages,claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated.

Trademarks
The Microchip name and logo, the Microchip logo, Adaptec, AVR, AVR logo, AVR Freaks, BesTime,BitCloud, CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer,LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo, MOST,MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip Designer,QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer,Tachyon, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip

Technology Incorporated in the U.S.A. and other countries.
AgileSwitch, APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, Flashtec,Hyper Speed Control, HyperLight Load, Libero, motorBench, mTouch, Powermite 3, Precision Edge,ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet- Wire, SmartFusion, SyncWorld, Temux, TimeCesium,TimeHub, TimePictra, TimeProvider, TrueTime, and ZL are registered trademarks of Microchip

Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut,Augmented Switching, BlueSky, BodyCom, Clockstudio, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, Espresso T1S, EtherGREEN, GridTime, IdealBridge, In-Circuit SerialProgramming, ICSP, INICnet, Intelligent Paralleling, IntelliMOS, Inter-Chip Connectivity, JitterBlocker,Knob-on-Display, KoD, maxCrypto, maxView, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certifiedlogo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net,PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, RTAX, RTG4, SAMICE,Serial Quad I/O, simpleMAP, SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI,SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total Endurance, Trusted Time, TSHARC,USBCheck, VariSense, VectorBlox, VeriPHY, ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.

The Adaptec logo, Frequency on Demand, Silicon Storage Technology, and Symmcom are registered trademarks of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies.

© 2023, Microchip Technology Incorporated and its subsidiaries. All Rights Reserved.
ISBN: 978-1-6683-2865-1
Quality Management System
For information regarding Microchip’s Quality Management Systems, please visit www.microchip.com/quality.

Worldwide Sales and Service

Corporate Office

2355 West Chandler Blvd. Chandler, AZ 85224-6199

Tel: 480-792-7200

Fax: 480-792-7277

Technical Support: www.microchip.com/support Web Address: www.microchip.com

Atlanta

Duluth, GA

Tel: 678-957-9614

Fax: 678-957-1455

Austin, TX

Tel: 512-257-3370

Boston Westborough, MA Tel: 774-760-0087

Fax: 774-760-0088

Chicago

Itasca, IL

Tel: 630-285-0071

Fax: 630-285-0075

Dallas

Addison, TX

Tel: 972-818-7423

Fax: 972-818-2924

Detroit

Novi, MI

Tel: 248-848-4000

Houston, TX

Tel: 281-894-5983

Indianapolis Noblesville, IN Tel: 317-773-8323

Fax: 317-773-5453

Tel: 317-536-2380

Los Angeles Mission Viejo, CA Tel: 949-462-9523

Fax: 949-462-9608

Tel: 951-273-7800

Raleigh, NC

Tel: 919-844-7510

New York, NY

Tel: 631-435-6000

San Jose, CA

Tel: 408-735-9110

Tel: 408-436-4270

Canada – Toronto

Tel: 905-695-1980

Fax: 905-695-2078

| Australia – Sydney

Tel: 61-2-9868-6733

China – Beijing

Tel: 86-10-8569-7000

China – Chengdu

Tel: 86-28-8665-5511

China – Chongqing

Tel: 86-23-8980-9588

China – Dongguan

Tel: 86-769-8702-9880

China – Guangzhou

Tel: 86-20-8755-8029

China – Hangzhou

Tel: 86-571-8792-8115

China – Hong Kong SAR

Tel: 852-2943-5100

China – Nanjing

Tel: 86-25-8473-2460

China – Qingdao

Tel: 86-532-8502-7355

China – Shanghai

Tel: 86-21-3326-8000

China – Shenyang

Tel: 86-24-2334-2829

China – Shenzhen

Tel: 86-755-8864-2200

China – Suzhou

Tel: 86-186-6233-1526

China – Wuhan

Tel: 86-27-5980-5300

China – Xian

Tel: 86-29-8833-7252

China – Xiamen

Tel: 86-592-2388138

China – Zhuhai

Tel: 86-756-3210040

| India – Bangalore

Tel: 91-80-3090-4444

India – New Delhi

Tel: 91-11-4160-8631

India – Pune

Tel: 91-20-4121-0141

Japan – Osaka

Tel: 81-6-6152-7160

Japan – Tokyo

Tel: 81-3-6880- 3770

Korea – Daegu

Tel: 82-53-744-4301

Korea – Seoul

Tel: 82-2-554-7200

Malaysia – Kuala Lumpur

Tel: 60-3-7651-7906

Malaysia – Penang

Tel: 60-4-227-8870

Philippines – Manila

Tel: 63-2-634-9065

Singapore

Tel: 65-6334-8870

Taiwan – Hsin Chu

Tel: 886-3-577-8366

Taiwan – Kaohsiung

Tel: 886-7-213-7830

Taiwan – Taipei

Tel: 886-2-2508-8600

Thailand – Bangkok

Tel: 66-2-694-1351

Vietnam – Ho Chi Minh

Tel: 84-28-5448-2100

| Austria – Wels

Tel: 43-7242-2244-39

Fax: 43-7242-2244-393

Denmark – Copenhagen

Tel: 45-4485-5910

Fax: 45-4485-2829

Finland – Espoo

Tel: 358-9-4520-820

France – Paris

Tel: 33-1-69-53-63-20

Fax: 33-1-69-30-90-79

Germany – Garching

Tel: 49-8931-9700

Germany – Haan

Tel: 49-2129-3766400

Germany – Heilbronn

Tel: 49-7131-72400

Germany – Karlsruhe

Tel: 49-721-625370

Germany – Munich

Tel: 49-89-627-144-0

Fax: 49-89-627-144-44

Germany – Rosenheim

Tel: 49-8031-354-560

Israel – Ra’anana

Tel: 972-9-744-7705

Italy – Milan

Tel: 39-0331-742611

Fax: 39-0331-466781

Italy – Padova

Tel: 39-049-7625286

Netherlands – Drunen

Tel: 31-416-690399

Fax: 31-416-690340

Norway – Trondheim

Tel: 47-72884388

Poland – Warsaw

Tel: 48-22-3325737

Romania – Bucharest

Tel: 40-21-407-87-50

Spain – Madrid

Tel: 34-91-708-08-90

Fax: 34-91-708-08-91

Sweden – Gothenberg

Tel: 46-31-704-60-40

Sweden – Stockholm

Tel: 46-8-5090-4654

UK – Wokingham

Tel: 44-118-921-5800

Fax: 44-118-921-5820

© 2023 Microchip Technology Inc. and its subsidiaries

References

• {波多野42部无码喷潮在线,18禁美女裸身无遮挡免费网站,国产成人精品一区二三区在线观看,久久精品国产亚洲AⅤ无码}
• Empowering Innovation | Microchip Technology
• Design Help and Other Services | Microchip Technology
• Microchip Lightning Support
• Empowering Innovation | Microchip Technology

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>