Extreme networks AP510e Extreme Mobility Indoor 802.11ax Access

Point

Extreme Mobility Indoor 802.11ax AP510e Access Point

The Extreme Mobility Indoor 802.11ax AP510e Access Point is a high-performance wireless access point that provides fast and reliable wireless connectivity. It requires a minimum base firmware of WiNG 7.1.1 and can be powered through Power over Ethernet (PoE) or an external 12V DC power supply.

AP510e Powering Methods

The AP510e can be powered through the following methods:

Ethernet ports
(LAN ports) of the AP510e, compliant to be powered with 802.3af and
provide full functionality with 802.3at. This is the preferred
method of powering the AP on ceiling and high wall
installations.
External 12V DC power supply (optional; ordering part #37219 –
PWR 12VDC, 3A, 2.5mm x 5.5mm connector)| The AP510e can also be powered by an external DC power supply
plugged into an AC source. Plug the supply’s input jack into the
12V DC port. Note that PoE is disabled when an external power
supply is used.

LEDs Status

The AP510e has several LEDs that indicate its status:

Verifying the AP510e Box Contents

Before installing the AP510e, verify that the following items are available:

Mounting and Connecting the AP

To mount and connect the AP510e:

1. Drill two holes 83mm (3.270) apart from each other on the wall where you want to mount the AP.
2. Insert the screws into the holes of the mounting bracket and use the screw-in anchors if needed.
3. Insert the Ethernet cable’s RJ45 connector into the LAN1/GE1 port.
4. Insert the AP onto the bracket’s four feet and slide it down to lock it in place.

Note that detailed installation information can be found in the Extreme Wireless AP510e Installation Guide.

Installing the Extreme Mobility Indoor 802.11 ax AP510e Access Point

Overview of the AP510e

The AP510e is a next generation, indoor ceiling mount model enterprise class 802.11ax access point. The “e” in AP510e indicates that it comes with external antennas. The AP features a dual-band radio, a band locked radio, eight RP-SMA WiFi ports, one Bluetooth port, and one internal Bluetooth Low Energy (BLE) antenna. The Bluetooth port can be used for a remote antenna in place of the internal antenna. The AP510e can be mounted on a dry or wood wall, solid flat ceiling, junction/gang box, and on a suspended or drop ceiling.

Note: The AP510e requires a minimum base firmware of WiNG 7.1.1.

The AP510e model has the following features:

• Radios: 2 radios (1 dual band, 2.4GHz and 5GHz, and 1 band locked 5GHz); 1 IoT radio (2.4 GHz)
• Console Port: RJ45
• Two Ethernet Ports
  • One multi-rate GE/2.5GE/5GE port (LAN1) with PoE In
  • 10/100/1000 Ethernet Port (LAN2) with PoE In
• LEDs : 6
  • All LEDs will be on during reset.
• One Reset button – Reset Instructions
• Power: PoE 802.3af; 12VDC external power in connector (see Table 1 for details)
• Antennas:
  • Eight RP-SMA external antennas
  • One RP-SMA BLE antenna
  • One BLE internal antenna
• Temperature:
  • -20 to 50°C ambient temperature anywhere
• Enclosure: Plastic with metal base

Figure 1 Top and Side Views of AP510e

1 USB Port

Table 1 AP510e Powering Methods

Note: PoE is disabled when external power supply is used.

Figure 2 AP510e back ports

Table 2 Description of back ports of AP510e

LEDs Status

The LEDs are located on the front face of the AP but are not visibly marked.
Table 3 AP510e LED Status

For detailed installation information about the AP510e, see the Extreme Wireless AP510e Installation Guide.

Verifying the AP510e Box Contents

Verify the contents of the box and ensure that the following items are available:
Table 4 Contents of the AP510e Box

Mounting and Connecting the AP

Electrical Hazard: Only qualified personnel should perform installation procedures.

Use these instructions as guidelines for mounting and connecting the AP510e easily and safely.The AP510e comes with a Mounting Bracket (#37201) that can be used to mount the AP on a flat t-bar with flat ceiling tiles, flat surfaces, beams, and some junction/gang boxes. An adaptor and brackets are available for mounting the AP to non-flat ceiling tiles and t-bars. To mount the AP510e on a junction/gang box, use the optional bracket (WS-MBI-WALL04;

30516). All additional and optional parts are sold separately.

Note: The mounting procedures for installing the AP using the WS-MBI- DCFLUSH (ordering part #37211) adaptor to a T-bar, WS-MBI-DCMTR01(ordering part #30518) to a T-bar, and using the main mounting bracket(ordering part

37201) along with a flat metal-easy attach adaptor (ordering part #37210),

Accessory BRKT-000147A-01 (beam clip), and KT-135628-01 are covered in the Extreme Wireless AP510e Installation Guide.

Mounting the AP on a Wood Wall/Solid Flat Ceiling

Pre-installation checklist:

• The mounting surface, item, and hardware must be able to support the AP in all environmental conditions.
• The mounting surface should be flat.
  • To install the AP on a dry wall or flat surface:

Option 1: Using the Main Mounting Bracket

1. Use the mounting bracket as a template and mark the hole centers on the wall.
   Note: The four feet of the bracket and the direction of the arrow mark must be vertical and pointing up and the flat part of the bracket must be touching the surface it is being attached to.

2. Drill two holes 83mm (3.270”) apart from each other on the wall where you want to mount the AP. Insert the screws into the holes of the mounting bracket and use the screw-in anchors if needed.

3. Insert the Ethernet cable’s RJ45 connector into the LAN1/GE1 port.

4. Insert the AP onto the bracket’s four feet and slide it down to lock it in place.
   Note: The T-bar width can be either 9/16” (15mm) or 15/16” (24mm).

Option 2: Using an optional Wall and Box bracket
For detailed instructions, see the ExtremeWireless AP510e Installation Guide.

Mounting the AP to a Suspended or Drop Ceiling

The AP510e can be mounted to a suspended or drop ceiling directly using the mounting bracket on the t-bar. If there is a ceiling tile protrusion, add the optional T-bar adaptor to the main mounting bracket prior to T-bar installation.
Option 1: Using the Main Mounting Bracket to a T-bar
Before installation ensure that:

• The base thickness of the T-bar that supports the ceiling tile is 0.031”.
• The maximum base thickness of the T-bar of the T-bar is 0.055”.
  Note: The T-bar width can be either 9/16” (15mm) or 15/16” (24mm).

1. Remove the ceiling tiles, slide and rotate the main mounting bracket onto the T-bar in such a way that the center angled locking tabs of the main bracket gets attached to the T-bar.
2. Replace the tiles to hold the T-bar in place.
3. Hold the AP and rock it back and forth to ensure it is securely mounted.
4. Attach the Ethernet cable’s RJ45 connector to the LAN1/GE1 port.

Option 2: Mounting the AP by attaching an adaptor to the main bracket For detailed instructions, see the Extreme Wireless AP510e Installation Guide.

Mounting the AP on a Junction or Gang Box
For detailed procedure on Installing the AP to a Junction or Gang Box, see the Extreme Wireless AP510e Installation Guide.

Mounting the AP to a Beam
For detailed procedure on Installing the AP to a Beam, see the Extreme Wireless AP510e Installation Guide.

Connecting a Power Supply to the AP510e
If you need to power the AP510e with an external 12V DC power supply, you can plug the power cord into the power connector on the back of the AP. There is no wall mount bracket for the 12V DC power supply. When the device is powered on, the power LED on the front face of the AP is lit. Refer to the Extreme Wireless AP510e Installation Guide for information about optional power supplies.

Antenna Configurations for External Antenna Models

Figure 3 AP510e External RP-SMA Antenna Connectors

Table 5 AP510e Antenna Configuration

Operational Description of Antenna Configuration and RF Output Power

Setting

Per KDB 353028 D01 Antennas Part 15 Transmitters v01 requirement, Applications must contain an exhibit listing each antenna, the antenna gain, antenna type, and antenna manufacturer/vendor and output power that can be used for the device, that the info listed below are correct and represent the product in consideration under this filing.

Professional Installation Instruction

Installation personal
This product is designed for specific application and needs to be installed by a qualified person who has RF and related rule knowledge. The general user shall not attempt to install or change the setting.

Installation location
The product shall be installed at a location where the radiating antenna can be kept 36 cm from nearby person in normal operation condition to meet regulatory RF exposure requirement.

External antenna
Use only the antennas which have been approved by the applicant. The non- approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/IC limit and is prohibited.

Installation procedure
Refer to installation manual for additional details.

Warning: Carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty.

Regulatory and Compliance Information Safety Guidelines

This section contains notices that are intended to protect your personal safety and prevent damage to the equipment.
Qualified Personnel:

Electrical Hazard: Only qualified personnel should perform installation procedures. Within the context of the safety notes in this documentation, qualified persons are defined as persons who are authorized to commission, ground and label devices, systems, and circuits in accordance with established safety practices and standards. A qualified person understands the requirements and risks involved with installing outdoor electrical equipment in accordance with national codes.

Federal Communications Commission (FCC) Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 51cm between the antenna & your body.
Note: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used.

Industry Canada Notice

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Caution: The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Warning: IC Radiation Exposure Statement: This equipment complies with IC radio-frequency exposure guidelines set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 31 cm between the antenna & your body.

Detachable Antenna Usage

This radio transmitter [4141B-AP510E] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Approved Antenna(s) list:

This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. Referring to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassessment permissive change.

Note: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used.

Other Countries

MPE Statement – Mobile Device

This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

CE Statement

The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.

All Operational Modes

• 2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), Bluetooth(BR/EDR, LE)
• 5GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160)
  • The frequency and the maximum transmitted power in EU are listed below:
  • 2412-2472MHz: 20 dBm
  • 2402-2480MHz (BR/EDR): 6 dBm
  • 2402-2480MHz (LE): 8 dBm
  • 5180-5240MHz: 23 dBm
  • 5260-5320MHz: 23 dBm
  • 5500-5700MHz: 30 dBm

European Waste Electrical and Electronic Equipment (WEEE) Notice

In accordance with Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE):

1. The symbol above indicates that separate collection of electrical and electronic equipment is required.
2. When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately.
3. It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment.
4. It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, contact Extreme Environmental Compliance at Green@extremenetworks.com.

Hazardous Substances

This product complies with the requirements of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Declaration of Conformity in Languages of the European Community

Hereby, Extreme Networks, declares that the radio equipment type [AP510e] is in compliance with Directive 2014/53/EU. For full text of the EU Deceleration of Conformity, please contact Extreme Regulatory Compliance at compliancerequest@extremenetworks.com

Extreme Mobility TM Access Points

Quick Reference

• AP510e-FCC
• AP510e-WR
• AP510e-FCC-TAA

Scan to Download the XIQ Mobile Application

Commission, monitor, and troubleshoot devices easily with XIQ Companion mobile application (supported on iOS and Android). Use your mobile device camera to scan the serial number, capture installation images, assign or change device location, and network policy. The XIQ Companion mobile application enables you to access the device CLI for troubleshooting and view device and client status.

Scan for Product Support Details

Notice
Copyright © 2023 Extreme Networks, Inc. All Rights Reserved.

Legal Notices
Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice.

Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of Extreme Networks, Inc. in the United States and/or other countries. All other names (including any product names) mentioned in this document are the property of their respective owners and may be trademarks or registered trademarks of their respective companies/owners. For additional information on Extreme Networks trademarks, please see: www.extremenetworks.com/company/legal/trademarks/

Documentation, Installation Videos, & Support

For product support, including Documentation and Installation Videos, visit: www.extremenetworks.com/documentation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>