Martha STEWART INS-0064 Everyday System 8FT Hanging and Shoe Storage System Instruction Manual

June 10, 2024
Martha Stewart

Martha STEWART INS-0064 Everyday System 8FT Hanging and Shoe Storage System Instruction Manual
Martha STEWART INS-0064 Everyday System 8FT Hanging and Shoe Storage
System

Congratulations on your purchase of the The Everyday System. Installing your system is straightforward if you follow our instructions in the order provided. Remember – measure twice, drill once!

A. Height of system
B. Distance between uprights

Cabinet height

C. Shelf and shelf bracket height
D. Width of system
E. Width of system
F. Depth of system

Front View
Dimension

Top View
Dimension

Order of Installation

Please follow the instructions in this order for optimum results and stability of your Everyday System.

  1. Prepare your space
  2. Uprights
  3. Shelf Brackets
  4. Standard Shelf
  5. Long Shelf
  6. Shoe Shelf
  7. Drawer Cabinet
  8. Bin Cabinet
  9. Mesh Door Cabinet
  10. Media Cabinet
  11. Desk Unit
  12. Closet Rod

Rules and Warnings

  • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL.
  • Do not attempt to assemble without FIRST securing Upright to the wall.
  • Failure to anchor this product to a wall and/or otherwise not follow assembly instructions shall void this warranty.
  • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.
  • After assembly, make sure all leveler feet are touching the ground.
  • Your system should be assembled per the template design. For stability of the system, each section must have at least 2, or combination of, the following with a minimum 40” spacing apart: Shelf, Shoe Shelf, Cabinet Unit.
  • Ceiling height must be at least 90” high to allow clearance for installation.
  • Trim must be less than 1-1/8” thick to allow for unit clearance.
  • Maximum height that a cabinet can be mounted is 44” from the top of the cabinet to the floor.
  • Do NOT re-use parts to attach wall bracket including screws and wall anchors.

If you intend to disassemble and reassemble this unit, please scan the QR code to visit the website for further instruction.
QR code

To watch videos detailing the installation process, please scan the QR code with your mobile device, or visit: shop.californiaclosets.com/pages /installation-everyday
QR code

Components Included

Qty| Description
4| Closet Rods with Mount 24 inch
5| Uprights 87.25 x 20 in
16| Basic Shelf Woodgrain 24 x 20 inch
3| Shoe Shelf with Mount Woodgrain 24 x 20 inch
16| Shelf Bracket Set 20 inc

  • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL
  • Do not attempt to assemble without FIRST securing Upright to the wall.
  • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves

Included Part

Note: Box may include more than one upright and hardware set.
Included Part

Tools Required

Included Part

Painter’s Tape

Included Part

2 Phillips

To watch videos detailing the installation process, please scan the QR code with your mobile device, or visit: shop.californiaclosets.com/pages /installation-everyday
QR code

Before you start your build do not forget to prepare your space!

Step 1: Tear out any unwanted structures (Example: previous wire closet)

Step 2: Repair any holes or damaged areas by patching and painting.
Instructions

Step 3: Verify your measurements and confirm the installation will fit. Examples:

Step 3a: If between two walls, measure baseboard to baseboard.
Instructions

Step 3b: Be aware of obstructions around the space such as wall lights, hanging lights, outlets, switches, etc.
Instructions

Step 4: Make note of anything that could be in the walls such as gas lines, electric wires, or water lines at Upright locations

Find the high spot in the floor

Option 1: Use a long level and move along perimeter of the floor noting where the highest point is. This is the high spot in the floor. (1a) Option 2:

Step 1 – Draw a light line on the wall that can be erased later.

Step 2 – Find the shortest distance between the floor and the line. This is the high spot in the floor.

Measure 87-1/4” from the high point (1b) and make a light mark (1c). This is your System Height.
Product Overawe

The Wall Template will assist you in properly spacing distances between uprights. To mark the first two upright locations, align the top of the template with the System Height line drawn in Step 1 (2a) and the middle of the first partition (2b) Make sure that the template is level. It is recommended to use tape to keep the template in position (2c).
Wall Template will

Depending on your Layout Design you will be using either the 16”, 24”, 30” or 48” holes for this span. Mark the two holes for each appropriate Upright location.
Depending

Reuse the Wall Template for the spacing for the next Upright. Using the previous marked holes as a starting point “START”, space out the next location depending on your Layout Design (16, 24, 30 or 48” span). Remember to check that the template is level and aligns with the System Height. Mark the next upright holes.
Wall Template

Repeat until all Upright hole locations are marked.
Product Overawe

WARNING: This wall bracket mount installation is specific to drywall with studs. If your wall is of different construction, you must find appropriate means to attach the wall bracket. It is not required to have the upright brackets be tied into a stud as drywall is acceptable.

Once all holes are marked, drill a hole at each location using a 1/8” drill.

If hole location is located on a stud, install wall mount bracket using method “A”. If the hole location is not located on a stud, install wall mount bracket using method “B”.

Method A: Wall Mount Bracket into a stud. Use two screws and attach wall mount bracket to wall.
Installations

Method B: Wall Mount Bracket no stud (Drywall). Using a #2 Philips bit, Install Easy Anchor into the 1/8” hole until flush. The Anchor will self drill. Use two screws and attach wall mount bracket to wall.
Installations
Ensure leveler is installed all the way into Uprights
Assembly Instructions

Place Upright on bracket (8a), and partially install screws to secure (8b). Do not tighten
Assembly Instructions

Adjust leveler leg to level Upright. Then make sure the back leveler also touches the ground. Ensure Uprights are level to adjacent Uprights.
Assembly Instructions

Once system is level, tighten all top screws. Double check that all levelers are touching the ground
Assembly Instructions

  • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL
  • Do not attempt to assemble without FIRST securing Upright to the wall.
  • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.

Included Parts

Tools

Tools Required
Tools

To watch videos detailing the installation process, please scan the QR code with your mobile device, or visit: shop.californiaclosets.com/pages /installation-everyday

Assembly Instructions
Assembly Instructions

Assembly Instructions

**** Do not install hole plug if bracket is used with a po

Assembly Instructions

If cover is accidentally installed, pry cover with screwdriver.

**** Do not install cover if bracket is used with drawer

Assembly Instructions

  • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL.
  • Do not attempt to assemble without FIRST securing Upright to the wall
  • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves

Included Parts

Included Parts
Included Parts

Tools Requi

Tools

To watch videos detailing the installation process, please scan the QR code with your mobile device, or visit:shop.californiaclosets.com/pages /installation-everyday
QR code

Assembly Instructions
Assembly Instructions
Assembly Instructions

**** Do not install hole plug if bracket is used with a pole.
Assembly Instructions
Assembly Instructions

If cover is accidentally installed, pry cover with screwdriver.

Assembly Instructions
Assembly Instructions
Assembly Instructions

  • THIS IS NOT A FREE-STANDING UNIT. FOR SAFETY, ALWAYS ANCHOR TO THE WALL
  • Do not attempt to assemble without FIRST securing Upright to the wall
  • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.

Included Parts

To watch videos detailing the installation process, please scan the QR code with your mobile device, or visit: shop.californiaclosets.com/pages /installation-everyday

Assembly Instructions
Assembly Instructions
Assembly Instructions
Assembly Instructions
Assembly Instructions

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Martha Stewart User Manuals

Related Manuals