ecollar PG-300 Remote Dog Training Collar Red Owner’s Manual
- June 9, 2024
- Ecollar
Table of Contents
- PG-300 Remote Dog Training Collar Red
- IMPORTANT NOTICE
- CHARACTERISTICS
- PACKAGE CONTENTS
- DEVICE OPERATION
- CHARGING THE BATTERIES
- TURNING YOUR E-COLLAR ON/OFF
- CORRECTLY FITTING COLLAR
- THE LCD DISPLAY DESCRIPTION
- BUTTON FUNCTIONS
- HOW TO FIND THE PROPER VIBRATION LEVEL
- LOCK/UNLOCK THE VIBRATION LEVEL
- HOW TO SET THE BOOST
- LOST TRANSMITTER MODE
- REPLACE/ADD COLLAR
- 302 LCD DESCRIPTION
- 302 BUTTON FUCTIONS
- HOW TO LOCK/UNLOCK THE VIBRATION LEVEL
- 302 BOOST LEVEL SETUP
- TRAINING TIP
- TROUBLESHOOTING
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
PG-300 Remote Dog Training Collar Red
Owner’s Manual
Welcome to the World of
E-Collar Technologies, Inc.
PG 300/302
www.pageronly.com
“Communication with your Best Friend has Never Been Easier”
Welcome to the World of E-Collar Technologies, Inc.
PG-300 Remote Dog Training Collar Red
PG 300 Series E-Collar Remote Education Collar
Thank you for purchasing the PG 300 or PG 302 Remote Education Collar from
E-Collar Technologies, Inc. We have made every attempt to provide you with the
most technologically advanced product using the most stringent quality and
manufacturing standards.
We are confident you will be pleased with the results you will attain with
your e-collar. Please remember you will get better results with the use of
lower stimulation combined with consistent training techniques.
The use of high levels of stimulation should only be used as a last resort and
in life-threatening situations. Visit our YouTube channel for training videos
and “Like” our Facebook page to network with fellow e-collar users.
Good luck with your training and please feel free to contact us should you
have any questions.
1-260-357-0051 or
sales@epageronly.com
IMPORTANT NOTICE
Caution
This product is intended to be used on DOGS ONLY.
E-Collar Technologies, Inc. is not responsible for any misuse of this product
including damages from dog bites and lost items. Seek an evaluation by
professional trainer before use on aggressive dogs. It is not uncommon for
aggressive dogs to associate the stimulation with the handler and take action
against the handler. Sometimes dogs put under e-collar pressure during a
fight can exhibit redirected aggression and become more aggressive.
The use of high levels of stimulation should only be used as a last resort and
in life-threatening situations.
To prevent giving stimulation to your dog by accident, keep the stimulation
level below 5 while not in use.
The range of the PG 300/302 may vary according to terrain, weather conditions,
foliage, and power lines as well as radio transmissions from other devices.
CHARACTERISTICS
- Range : 2 Mile
- Three Vibration Modes Supported (Momentary, Continuous, and Combo Mode)
- Tapping Sensation or Tone Tapping Sensation: Alternative to Stimulation (give vibration similar to a Cell Phone) Tone
- Quick Charge Li-Polymer Batteries
- Convenient Intensity Dial for Quick Adjustment
- Vibration Levels Adjustable from 0 to 100
- Collar Receiver Light for locating your dog at night
- Lock and Set Stimulation Safety Feature
- Vibration Boosting Mode provides instant control when normal stimulation is ignored – great for emergency situations.
- User Adjustable Boosting Levels from 1 to 60 Levels
- Completely Waterproof
- Convertible from 1-Dog model (PG 300) to 2-Dog model (PG 302)
PACKAGE CONTENTS
DEVICE OPERATION
CHARGING THE BATTERIES
Indicator Light is blinking “Green” under normal operation. solid “Red” when
stimulation is applied. blinking “Red” when recharging is required.
Do not allow the batteries to get hot o
The indicator light will turn solid red during charge cycles and turn green if
it is fully charged. (approximately 2 hours)
Please add this about the batteries:
Your e-collar is outfitted with Li Polymer batteries which requires specific
care to assure longevity. It is best not to let the battery be fully
discharged and if it does, recharge immediately or irreversible damage may
occur. Keep the units away from extreme heat and cold temperatures.
TURNING YOUR E-COLLAR ON/OFF
-
To turn the Collar Receiver On or Off :
Place the small red dot on the Transmitter to the small red dot on the Collar Receiver. -
To turn the Transmitter On or Off:
Press the “L” button for more than 1 second.
If the Transmitter is turned on, a short press of the “L” button will activate the tracking light of the collar receiver. Press and hold for 2 seconds to turn Transmitter off. -
Holding the Transmitter
To obtain the maximum range hold the transmitter like the torch on the Statue of Liberty. Keep the antenna away from your body or fingers at all times, touching the antenna will greatly reduce the range.
CORRECTLY FITTING COLLAR
You should be able to fit a couple of fingers between the collar strap and your dog’s skin. Too tight poses discomfort. Too loose will not be able to administer the stimulation reliably.
THE LCD DISPLAY DESCRIPTION
Blinking “1D” indicates the vibration level ready for adjustment.
Solid “1D” indicates vibration level is “Locked” Displays the Vibration Level
:
“0” means no vibration and “HI” means the highest vibration level(100)
Momentary / Continuous Button “M/C”- The M/C Button on the backside of
the transmitter allows the user to easily switch between the three vibration
modes. The function of stimulation buttons changes by mode.
To change the mode: Press and hold the M/C button for 2 seconds to enter change mode indicated by a beep. Then Press and release the M/C button to change from M (Momentary) to C (Continuous) to M+C (Combo — Momentary/Continuous) stopping on the desired mode.
Stimulation Button
| Combo Mode| Momentary Mode|
Continuous Mode
---|---|---|---
Display| | |
S (Black)| Momentary| Momentary| Continuous
S (Red)| Continuous| Momentary Booster| Continuous Booster
S(Black)+S(Red)| Momentary Booster| N/A| N/A
S(Red)+S(Black)| Continuous Booster| N/A| N/A
T| Tapping Sensation or Tone Stimulation
BUTTON FUNCTIONS
Momentary Vibration
Sends a single pulse of vibration at the set level when you press stimulation
button.
Continuous Vibration
Sends vibration for as long as the button is pressed, timing out after 10
seconds (this is a safety feature designed to prevent accidental over-
stimulation of your dog). The stimulation can be increased or decreased while
the button is being pressed.
Tapping Sensation
Vibration specifically designed to distract your dog, great for deaf dogs.
Tone
Flat sound up to 30 second.
Stimulation Button S (Black)
– Sends momentary or continuous vibration to the collar receiver based on the
state of Momentary/Continuous Mode.
Stimulation Button S (Red)
– Sends momentary or continuous boosted vibration.
– If vibration level is 10, boosted vibration sends [10 + boost level ] – The
default value of the boosted level is 5, it can be adjusted to any value
between 1 and 60. Smaller and more sensitive breeds should use levels 1
through 20, larger and/or more stubborn breeds may need a higher boost.
Boosting vibration in Combo Mode
Momentary Boosting is accomplished by first sending a momentary vibration
pulse “S (Black)” to the dog and then pressing “S (Red)” button without
releasing “S (Black)” button. (PLEASE PRACTICE) Continuous Boosting is
accomplished by first administering continuous vibration “S (Red)” to the dog
and then pressing the “S (Black)” button without releasing the “S (Red)”
button.
Tapping Vibration / Tone “T”
Sends Tapping Sensation or Tone to the collar receiver.
(Default setting is tapping sensation).
To toggle between tapping sensation and tone press “L” and “T” buttons
simultaneously when the intensity level is “O”.
– Single beep and “A” icon indicates tone.
– Double beeps and “T” icon indicates Tapping Sensation (Vibration).
Tapping Sensation Tone
Light Button “L” (ON/OFF Center Button on Back)
Pressing “L” button will change the night tracking light mode.
OFF - > Flashing -> Solid -> OFF
Great for locating your dog after dark. (PLEASE PRACTICE)
HOW TO FIND THE PROPER VIBRATION LEVEL
Rotating clockwise increases the stimulation level, and rotating counter-
clockwise lowers the stimulation level.
It is highly recommended that the user practices changing levels and modes
before putting the collar receiver on a dog.
Setting the correct vibration level for your dog is very important. To set
your “conditioning” vibration level, correctly put the collar receiver on your
dog (see page 9 for instructions). Let the dog get used to the collar
receiver for a couple of hours.
While watching your dog, turn the level to “O” and press the
continuous stimulation button. Slowly turn the stimulation up at a rate of
approximately 2-3 levels per second. When your dog first perceives the
stimulation , usually between 5 and 20, release the button. This is your
“conditioning” vibration level. You may need to increase the “conditioning”
level a few levels to get your dog to respond at first, some dogs are more
stubborn and need more stimulation. The boosted level is typically 5 to 20
levels higher than the “conditioning” level.
LOCK/UNLOCK THE VIBRATION LEVEL
How to Lock/Unlock the Vibration Level
Set the desired vibration level and then press on the top of the stimulation
dial until you see “1D” light up on the top portion of the LCD display.
Flashing “1D” indicates unlocked vibration and Solid “1D” indicates locked
vibration level.
If the vibration level does not change when you rotate the stimulation knob,
you have successfully locked the vibration level.
To unlock the vibration level simply press the stimulation knob again and it
will unlock the vibration level.
HOW TO SET THE BOOST
Boosted vibration adds the set boost level to the vibration level, great for those situations when your dog does not respond to the “conditioning” level. Determining the Boosted vibration level is a little more difficult than vibration level setting due to the wide differences in temperaments and vibration tolerance among the many breeds of dogs. On average, it is normally 5 to 20 levels higher than the “conditioning” level. It is important to have it set high enough to get the desired response from your dog.
- Change the mode to Momentary Mode. (Press M/C button until “M’” is displayed)
- Change the intensity level to “O”.
- Press S(Black) button for more than 5 seconds.
- The intensity level will change from “0” to a flashing “1”.
- Rotate the dial to the desired boost level (1 to 60).
- Press S(Black) button again to save and exit the boost level changing mode.
LOST TRANSMITTER MODE
Your PG 300/302 E-Collar transmitter allows the user to activate a 6 hour
timer. After 6 hours, the transmitter will begin to beep providing the ability
to locate the transmitter. The LCD displays “AL” during beeping. Lost
transmitter mode is activated by simultaneously pressing the Light (L) button
and the stimulation button (Black “S”) when the intensity level is set to
zero. Three short beeps will sound confirming the activation of the locator
timer.
Lost transmitter mode is deactivated by simultaneously pressing the Light (L)
button and the red stimulation button (Red “S”) when the intensity level is
set to zero. Two short beeps will sound confirming the deactivation of the
locator timer.
Lost transmitter mode will be cancelled whenever the transmitter is turned
off.
Make sure to reactivate lost transmitter mode when you turn off transmitter.
REPLACE/ADD COLLAR
Occasionally, it is necessary to pair/sync a transmitter to a collar receiver, the following procedure will accomplish this:
- Turn on the Transmitter
- Turn intensity dial to “O”
- Make sure the collar receiver is turned off.
- Put the Transmitter’s Red Dot against the Collar Receiver’s Red Dot for more than 5 seconds, green light on Receiver will flash rapidly
- Immediately after, press and hold Black “S” Button followed by the Red “S” Button until you hear confirmation sound from Collar Receiver.
HOW TO CHANGE THE TRANSMITTER TO A 2 DOG TRANSMITTER
The button functions will change. The changes are described on pages 18
through 22. You can change the transmitter back to the 1Dog system (PG 300) at
any time.
- Turn on the Transmitter.
- Press the Red “S” followed by the Black “S” followed by the “T” Button simultaneously for more than 2 seconds until you hear the confirmation beeps.
- Repeat step 2 to return back to a 1 dog system.
ADD/REPLACE COLLAR FOR SECOND DOG
- Turn on the Transmitter
- Turn intensity dial to “0”
- Make sure Receiver is turned off.
- Put the Transmitter’s Red Dot against the Collar Receivers Red Dot for more than 5 seconds, green light on Receiver will flash rapidly.
- Immediately after, press and hold Red “S” Button followed by the Black “S” Button until you hear confirmation sound from Collar Receiver.
302 LCD DESCRIPTION
Momentary / Continuous Button “M/C”- M/C Button on the backside of the transmitter allows the user to easily switch between two vibration modes either momentary or continuous.
Button
| Vibration Mode (1D or 2D)|
TS(Vibration)or Tone
---|---|---
M/C Button
| Momentary Mode| Continuous Mode|
N/A
Display
| | |
S (Black)
| Dog 1 Momentary| Dog 1 Continuous|
Dog 1 TS (Vibe) or Tone
S (Black) + S(Red)
| Dog 1 Momentary Booster| Dog 1 Continuous Booster| N/A
S (Red)| Dog 2 Momentary| Dog 2 Continuous|
Dog 2 TS (Vibe) or Tone
S(Red)+ S(Black)
| Dog 2 Momentary Booster| Dog 2 Continuous Booster| N/A
L| “L” in Dog 1 set mode will control Dog 1 light
“L” in Dog 2 set mode will control Dog 2 light|
N/A
302 BUTTON FUCTIONS
Mode Button “T”
Mode button allows the user to change modes as shown in the diagram
1 Dog Set Mode – LCD display shows 1D
2 Dog Set Mode – LCD display shows 2D
Tapping Sensation or Tone – LCD display a T
Light Button(On Back) “L”
When the “L” button is pressed, “L” will be displayed.
If you press L while in Dog 1 Mode, Dog 1’s Light will activate.
If you press L while in Dog 2 Mode, Dog 2’s Light will activate.
Tracking Light will Cycle: Flashing -> Solid -> OFF when L is pressed.
Tapping Sensation / Tone “T”
To toggle between tapping sensation and Tone press “L” and “T” buttons
simultaneously for 2 seconds when the intensity level is “O”.
– Single beep and “A” icon indicates tone.
– Two beeps and “T” icon indicates tapping sensation.
Momentary Vibration
Sends a single pulse of vibration at the set level when you press stimulation
button.
Continuous Vibration
Sends vibration for as long as the button is pressed, timing out after 10
seconds (this is a safety feature designed to prevent accidental over-
stimulation of your dog). The stimulation can be increased or decreased while
the button is being pressed.
Tapping Sensation
Vibration specifically designed to distract your dog, great for deaf dogs.
Tone
Flat sound up to 30sec
Boosting Stimulation
Sends boosted vibration until you release buttons.
To boost Dog 1, press “S” (Black) button followed by “S” (Red) button
To boost Dog 2, press “S” (Red) button followed by “S” (Black) button
HOW TO LOCK/UNLOCK THE VIBRATION LEVEL
How to Lock/Unlock the Vibration Level
See page 13 for help finding the proper vibration level.
You can lock each dog to a different level.
In 1Dog Mode, if you see “1D” icon is blinking (unlocked) Set the desired
vibration level and then press the stimulation dial until you see “1D” icon
stop blinking.
In 2Dog Mode, if you see “2D” icon is blinking (unlocked) Set the desired
vibration level and then press the stimulation dial until you see “2D” icon
stop blinking.
If the vibration level does not change when you rotate the stimulation dial,
you have successfully locked the vibration level.
To unlock the vibration level simply press the stimulation knob again at
1Dog/2Dog mode and it will unlock the vibration level.
302 BOOST LEVEL SETUP
Boosted vibration adds the set boost level to the vibration level, great for those situations when your dog does not respond to the “conditioning” level. Determining the Boosted vibration level is a little more difficult than vibration level setting due to the wide differences in temperaments and stimulation tolerance among the many breeds of dogs. On average, it is normally 5 to 20 levels higher than the “conditioning” level. It is important to have it set high enough to get the desired response from your dog.
How to Setup Boost Level for first dog
- Change the mode to Momentary Mode (Press M/C button until “M” is displayed)
- Change the intensity level to “O”
- Press S(Black) button for more than 5 seconds
- The intensity level will change 0 to 1 and start to blink.
- Rotate the dial to change the boost level (up to 60).
- Press S(Black) button again to save and exit from Boost Level Change Mode. If any other button is pressed or idle for 20 sec, Boost Level Change Mode will be cancelled.
If you want to change boost level for dog 2, Press S(Red) instead of S(black) on step #3, and #6
TRAINING TIP
IMPORTANT TRAINING TIPS
E-Collars can be used to reinforce commands your dog already knows or as a
learning sensation when paired with leash pressure. It is not a replacement
for basic leash obedience training, but a tool to allow you to better
communicate with your dog. For best results, use the least amount of
stimulation required to get the attention of your dog.
A calm and consistent approach to training will always produce better long
term results. It is highly recommended that aggressive dogs be taken to a
professional trainer for evaluation before e-collar use. There are many
different e-collar training techniques recommended by a variety of
professional trainers. We believe you, the owner of the dog, can best
determine the most successful technique for your dog. We recommend first time
users to emerge themselves in learning about the proper techniques or seek a
professional e-collar trainer.
The technique used in the initial introduction of the e-collar is very
important to the success of e-collar training. Search E-Collar Technologies on
YouTube and subscribe to our channel, new training videos are posted weekly.
Also “Like” and subscribe to our Facebook page to receive more training advice
and connect with other e-collar users.
Good Luck with your training from your friends at E-Collar Technologies
TROUBLESHOOTING
My Receiver / Transmitter is not turning on
Make sure the collar receiver is fully charged. Collar receiver light should
turn green when the battery is connected to the charger.
My Receiver is not responding
Check Receiver’s indicator light is blinking green and Transmitter LCD is on.
Check to make sure the collar receiver’s indicator light is red when the
stimulation button is pressed.
Try pairing/syncing the transmitter to the receiver. (Page 17)
Max range of device has been decreased
Check Transmitter’s battery condition. Working range decreases when the
battery level is low.
Keep your fingers from touching the antenna. See the bottom of page 8 for the
proper technique to maximize range.
You cannot change the vibration level of the Transmitter
Make sure 1D or 2D on transmitter LCD is blinking. If 1D or 2D icons are
solid, you cannot change vibration level. You can unlock the vibration level
at any time by pressing the stimulation knob for 1 second.
CONTACT US FOR EXPERT HELP WITH YOUR E-COLLAR
TWO YEAR WARRANTY
To register your PG 300/302 product, please log onto our website at
www.ecollar.com, click on the warranty registration
link and fill out the required information. Please register your product
within 30 days of your purchase. If you do not have access to a computer,
please call our toll free number of
1-855-326-5527 and one of our customer
service representatives will register your product for you. In the event the
product is not properly registered proof of purchase is not required to obtain
warranty, we will estimate your purchase date by the serial number. Misuse,
improper maintenance, lost units are not covered by this warranty. Your
complete satisfaction is our only concern.
The PG 300/302 mini Educator you have is our most recent design, it is
different from the previous PG 300 and 302, so please let us know that you
have the new mini Educator design when communicating with us.
“Making Bad Dogs Good and Good Dogs Better!”
ACCESSORIES
SAFETY AND GENERAL INFORMATION
The PG 300/302 Education Collar complies with all National and International
Standards and Guidelines for human exposure to radio frequency electromagnetic
energy.
Nearly all electronic devices are susceptible to electromagnetic interference
(EMI) if inadequately shielded or designed without precautions to EMI.
PG 300/302 e-collar transmitters manufactured by E-Collar
Technologies, Inc. comply with Article 15 of the FCC rules and operate under
Part 95 of FCC regulations.
Operating Frequency Band is 27.095 MHz.
IMPORTANT NOTICE
- To avoid Electromagnetic Interference and/or compatibility conflicts, please turn off your transmitter and collar receiver in any facility where posted notices instruct you to do so. Never use your equipment in close proximity of a Hospital or Health Care Facility or enter the facility without turning off both units.
- An FCC license is not needed to operate PG 300/302 remote e-collar transmitters. However, any change or modification made to the transmitter, including the supplied antenna, without the expressed written approval of E-Collar Technologies, Inc. could void your authority to operate.
TRAINING NOTES
E-Collar Technologies, Inc.
2120 Forrest Park Drive
Garrett, IN 46738-1887
1-260-357-0051 (US & International)
1-855-326-5527 (US Toll Free)
1-855-226-5527 (US Toll Free Fax)
sales@ecollar.com
www.ecollar.com
customerservice@ecollar.com
http://www.ecollar.com
Thank you for Supporting American Workers
Copyright 2015 E-Collar Technologies, Inc.
All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>