CANVAS 152-2690-2 Barton 1-Light Wall Sconce Instruction Manual

CANVAS 152-2690-2 Barton 1-Light Wall Sconce

Product Information

Specifications

• Product Name: BARTON 1-LIGHT WALL SCONCE
• Product No.: 152-2690-2, GL65000062

Product Usage Instructions

Assembly Instructions
Before beginning assembly, please read the manual carefully and keep it for future reference.

Electrical Installation:

1. All electrical connections must comply with local codes and regulations.
2. Mount the fixture on an electrical outlet box directly supported by the building structure.
3. Turn off the circuit breaker or remove the fuse before installing the fixture.
4. Consult a qualified electrician if unsure about electrical installations.

ASSEMBLY INSTRUCTIONS
HAVING TROUBLE?TOLL-FREE:
1-888-670-6684
IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.

IC WARNING
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development (ISED) Canada’s licence- exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The device has been evaluated to meet general RF exposure requirement.
The distance between user and products should be no less than 20cm.

FCC WARNING

This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The distance between user and products should be no less than 20cm.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

REDISCOVER YOUR SPACE

• We believe in the power of décor and its ability to make up the fabric of your home.
• That’s why CANVASTM collections draw inspiration from Canadians and the way they live.
• From on-trend furniture pieces to holiday décor and all your outdoor living essentials, CANVASTM makes it easy to refresh your space to reflect your unique style and the way you live every day.
• We would love to hear from you and welcome your thoughtful feedback. Visit our website at canadiantire.ca to tell us about your experience, and share your photos with us using #myCANVASstyle.
• Show us how you bring CANVASTM products to life. We can’t wait to see!

WARNING! CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
CLEANING: Before cleaning your fixture, turn off the switch or power source. Wipe the fixture with a soft, damp cloth.
IMPORTANT: RETAIN FOR FUTURE REFERENCE, AND READ CAREFULLY.

IMPORTANT SAFETY INSTRUCTIONS!
HARDWIRE: READ INSTRUCTIONS AND REVIEW ALL DIAGRAMS BEFORE INSTALLING FIXTURE.

1. All electrical connections must be in accordance with local codes, ordinances and the Canadian Electrical Code.
2. These fixtures should be mounted on an electrical outlet box. The box must be directly supported by the building stucture.
3. Turn off the circuit breaker or remove the appropriate fuse to disconnect power source before installing fixture.
4. Turning the light switch off to cut the power is not sufficient to prevent electric shock. When in doubt about the safety of any electrical installation or repair, consult a qualified electrician.

IMPORTANT SAFETY INSTRUCTIONS!
PLUG-IN: READ INSTRUCTIONS AND REVIEW ALL DIAGRAMS BEFORE INSTALLING FIXTURE.

1. This portable lamp has a polarized plug (one blade is wider than the other) as a safety feature to reduce the risk of electric shock.
2. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
3. Never use with an extension cord unless the plug can be fully inserted.
4. Do not alter the plug.

TOOLS REQUIRED

PARTS LIST

HARDWARE LIST

BEFORE YOU BEGIN ASSEMBLY

MAKE SURE ALL PARTS ARE PRESENT
Compare all pieces to the parts and hardware lists, and make sure you have all tools required for assembly.

ASSEMBLE IN A CLEARED AREA
Place all parts from the box on the floor in front of you on a clean, dry, level surface to protect the product as it is being built.

REMOVE PACKAGING MATERIALS
Place packing materials back in the box. Do not dispose of packaging materials until assembly is complete.

READ EACH STEP CAREFULLY
Make sure you understand each step. For any questions, contact CANVAS™ customer service at 1-888-670-6684 (toll-free).

ELECTRICAL INSTALLATION

1. STEP 1
   Place the wall switch in the “OFF” position.

2. STEP 2
   Depending on which type of fuse box you have in your home:

   • Place either the main (Master) switch in the “OFF” position, cutting off power to your entire home, OR turn off the individual switch that provides power to where the fixture will be installed.
   • Place either the main (Master) switch in the “OFF” position, cutting off power to the entire home, OR unscrew the fuse that provides power to where the fixture will be installed.
   • NOTE: Shutting off a wall switch that controls the light is not sufficient to prevent electric shock.

WARNING! CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.

EXPLODED PARTS

STEP-BY-STEP GUIDE — HARDWIRE

1. STEP 1
   Remove the plug-in backplate H from the fixture 1 by unscrewing the canopy screws D.
   Remove the wire connectors B. Separate the wires from the cord, and gently pull on the cord to slide it out of the fixture 1 to remove it.

2. STEP 2
   Attach the white wire from the house to the white wire from the fixture 1 using one of the included wire connectors B.
   Then, attach the black wire from the house to the black wire from the fixture 1 in the same way. Wrap the bare wire from the fixture 1 around the grounding screw on the backplate. Finally, attach the green ground wire (or bare copper wire) from the house to the bare wire from the fixture 1.
   Position the mounting black backplate C over the outlet box and secure it with the outlet box screws A.

3. STEP 3

   • Position the fixture 1 in place, making sure all the wires are secure inside the junction box.
   • Place the canopy screws D to secure the canopy of the fixture 1 to the mounting backplate C.
   • Insert nut E into the canopy.
     WARNING:
     Ensure no exposed wires once all wiring is complete.

4. STEP 4

Screw one medium base (E26) LED bulb max. 60 W equivalent I into the socket of the fixture 1.

STEP-BY-STEP GUIDE — PLUG-IN

1. STEP 1
   • Mark the location for wall anchors F 2 3/4” (7 cm) apart. Use a 6 mm drill (not included) to make the holes.
   • Insert the anchors F into the wall. Screw the mounting wall screws G into the anchors F.
   • Align the backplate of the fixture 1 with the mounting screws G and press so that the screws are inserted in the plug-in backplate H of the fixture 1. Slide the fixture 1 down to lock it in place.
2. STEP 2
   Screw one medium base (E26) LED bulb max. 60 W equivalent I into the socket of the fixture 1.

TECHNICAL DATA

SPECIFICATIONS

TROUBLESHOOTING

HAVING TROUBLE? LET US HELP YOU!
BEFORE RETURNING YOUR PRODUCT
TOLL-FREE:
1-888-670-6684
If you have questions regarding your product or require warranty assistance, please call our customer service helpline.

PRODUCT TROUBLESHOOTING

CARING FOR YOUR ITEM

1. Disconnect fixture’s plug from wall receptacle
2. To clean the fixture, use a dry or slightly dampened clean cloth  (use clean water, never a solvent) to wipe the glass and surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives.
4. If necessary, use a mild soap to clean off any dirt or stains.

WARRANTY

This CANVASTM product carries a one (1) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.

PRODUCT NO. 152-2690-2,GL65000062
Made in China
Imported by Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8

References

• Shop Canada’s Top Department Store Online & at 500+ Locations | Canadian Tire

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>