ecollar 1000 Series Happiness is A Dog that Stays Home Instructions
- July 16, 2024
- Ecollar
Table of Contents
ecollar 1000 Series Happiness is A Dog that Stays Home
1000 Series E-Fence System
Thank you for purchasing the 1000 Series Wired E-Fence System from E-Collar
Technologies, Inc. We have made every attempt to provide you with the most
technologically advanced product using the most stringent quality and
manufacturing standards.
Good luck with your dog’s safe containment and please feel free to contact us
should you have any questions.
1-260-357-0051
Characteristics
- Supports Multiple Dogs
- Stimulation Level Adjustable up to 30 levels
- Over-Stimulation Prevention
- Run Through Prevention
- Anti-Linger Protection
- Tone Only Test Mode
- Waterproof & Shock Resistant
- Employs Quick Charge Li-Polymer Batteries
Contents
Wall Mount Controller
-
Power Switch : The containment system can be turned on or off by sliding the POWER switch to the ON or OFF position.
-
Field Width Adjustment Dial : Field Width Adjustment Dial controls the distance from the wire. The dog receives the warning tone and containment stimulation. To increase the field width, simply turn the dial clockwise, to reduce the field width, turn it counter-clockwise. A minimum of 6′ containment field is suggested.
-
Alarm Volume Adjustment : When containment system senses an error, there will be an alarm to alert the user. Alarm volume can be adjusted by sliding Alarm Volume slide switch.
-
Warning Tone : If warning tone is turned “ON”, there will be a warning tone with containment stimulation. Default value is “ON”.
-
Dog Size Selector: Dog Size Selector consists of small(SM), medium(MED), and large(LG) options. The below chart is a recommended starting point. Dogs of different size exhibit varying sensitivities to stimulation. You, the owner, are better at determining the tolerance and temperament of your dog. It is recommended to start low and adjust upwards until the boundary is well understood.
-
Stimulation Level Control : The correction level of each collar receiver is set separately. Stimulation levels consist of 11 settings from “1” to “H (10)” stimulation levels and “0” (tone only). You can change the level by pressing up & down arrow button. Default value is tone only. If you select tone “0” (tone only), there will be no stimulation. The output of each level varies depending on the dog size setting selected. See chart below.
-
Collar Receiver Setting Button: To change the setting of a collar receiver, place the collar receiver on top of the controller and press the set button. ( See section 8. “Customizing the Collar Receiver” for moro details )
-
Status Light and Alarm : The status light and LCD display provide the operational condition of the wall mount transmitter.
-
Power Connection : The power for the 1000 Series Controller is provided by a supplied UL certified 24 V, 400mA AC adapter.
-
USB Port : USB port to charge the collar receiver, any USB port connected with 5V DC adaptor can be used.
-
Loop Wire Terminals: The containment wires connect to the wall mount controller through the bottom of the case via the quick connect terminals.
-
Yard Switch : You can choose Normal Yard or Large Yard by sliding the yard switch.*
On select models. -
Back-up Battery : 8 hours of backup power can be provided by installing 6 AA Alkaline batteries when power to the controller is disconnected.
Collar Receiver
Special Features
Over Stimulation Prevention :
To protect your dog from accidental over stimulation, the collar receiver will
turn off after 10 seconds of stimulation for 10 seconds of relaxation. If the
dog chooses to remain in the containment field, the 10 seconds on and 10
seconds off cycle will repeat for 4 repetitions. After the fourth cycle, the
collar receiver will no longer stimulate until the dog returns to the safe
area.
Anti-Linger Protection :
This feature will administer the containment stimulation if the dog lingers in
the containment field. The stimulation level will gradually increase as a
cycle below. 
Run Through Prevention:
The collar receiver will sense if the dog is attempting to run through, the
system will administer the selected level of containment stimulation
instantly.
Important Note :
The special features mentioned on this page are integrated into the collar
receiver and work without any programming.
- Charging the Battery of Collar Receiver
- Indicator Light will blink “Green” under normal operation.
- Rapid Green when warning tone is applied.
- Rapid Red when stimulation is applied.
- Blinks Amber when charging is required.
- The indicator light will turn solid red during charge cycles and will turn green once it is fully charged. (approximately 2 hours)
Special Note About Battery Care
Your e-collar is equipped with Li-Polymer batteries that need specific
attention to ensure their longevity. It is advisable to avoid fully
discharging the battery. In the event of complete discharge, please recharge
it promptly to prevent irreversible damage. Additionally, please keep the
units away from excessive heat and cold temperatures. 
Customizing Collar Receiver
The default setting is tone only mode. Each collar receiver can be programmed
to offer a warning tone, small, medium, & large dog stimulation profiles, with
10 levels of stimulation within the selected dog size stimulation profile.
Before you put the collar on your dog, the collar should be programmed. Each
collar can be programmed differently by the combination of warning tone,
stimulation level and dog size selection.
How to customize the Collar Receiver.
- Change the value of warning tone, stimulation level, and dog size on the controller.
- Place the collars on the top of the controller.
- Press the “SET” button until the LED on the collar flashes from red to green.
- If the LED keeps blinking green, it means collar setting is finished.
Pairing Instructions:
Rx-1000 Replacement Receiver for E Fence
When you receive your replacement receiver for your underground fence, please
remember to program your settings from your transmitter to the new receiver.
Please note that the replacement receivers come standard with tone only and do
not provide any kind of stimulation. 
To program your receiver, simply place it on top of your transmitter box and press and hold the set button. This will transfer your current settings to your collar receiver. Remember, if you make any adjustments to the settings on your transmitter box, you’ll need to program your receiver for these changes to take effect.
Replacing the Contact Points
The standard 5/8″ contact points are used for most dogs.
Thicker fur breeds require the longer 3/4″ contact points.
Replace the 5/8″ contact points by following the instructions below using the
enclosed contact point tool.
-
Loosen both contact points by rotating the contact point counter-clockwise using the contact point tool.
-
Install the 3/4″ contact points onto the bolt and tighten the contact points by rotating them clockwise with the contact point tool.
-
For dogs with either very short or very long or thick coats, please contact customer service for an appropriate size set of contact points.
Correctly Fitting the Collar
- The collar should be adjusted to allow the “contact points” to have direct contact with the dog’s skin.
- You should be able to fit a couple of fingers between the collar strap and your dog.
- Too tight poses the risk of skin irritation and discomfort.
- Too loose and the contact points will not be able to administer the stimulation reliably and can cause skin irritation due to chafing.
- Short hair breeds may need the micro-probes offered as an accessory item, contact customer service for details. The optimal position for the collar receiver is on either side of the dog’s neck.
IMPORTANT NOTICE
To prevent the occurrence of skin irritations the Collar Receiver should never
be worn for more than 12 hours per day.
Should your dog experience skin irritations from over exposure to the contact
points remove the collar receiver unit immediately and stop using your
Containment system until all the skin irritations are totally healed.
Antibiotic ointment will aid in the healing process. Some dog breeds have very
thick fur that requires special contact points, please contact our customer
service.
To Register for the 2 Year Warranty
Two Year Full Warranty:
To register your product, kindly visit our website at
www.ecollar.com. Click on the warranty registration
link and complete the necessary information. We kindly ask that you register
your product within 30 days of your purchase. If you are unable to access a
computer, please feel free to contact one of our dedicated customer service
representatives at 1-260-357-0051. They
will be happy to assist you in registering your product. If, for any reason,
your product is not registered properly, proof of purchase will not be
required to obtain warranty coverage. We will be able to estimate your
purchase date based on the serial number. It is important to note that misuse,
improper maintenance, lost or stolen units, and dog damages are not covered
under the manufacturer’s warranty. We strive for your complete satisfaction
and aim to provide exceptional service.
Accessories
Important Notice
-
Item should be placed out of the reach of children.
This product is not meant to be used by individuals (including children) with limited physical, sensory, or cognitive abilities, or those lacking expertise and understanding, unless they are under the supervision or guidance of a person responsible for their safety. This also applies to the cleaning and upkeep of the item. -
The item should exclusively be used with the power supply (charger) provided with the product.
-
Possible Metal Allergy Dogs vary in sensitivity and may develop symptoms of a metal allergy. Which may include irritation, redness, hair loss, sores, etc. Please rotate collar receiver from side to side daily to check for allergies.
-
If allergies occur, hypoallergenic contact points are available for purchase at www.ecollar.com or 260-357-0051
NOTICE TO PREVENT WATER DAMAGE
If Receiver is exposed to water on a regular basis, tighten screws once or
twice a month depending on the frequency of water exposure. Please make sure
screws are snug but not overly tight. This will help prevent internal water
damage.
Technical Specifications
1000 Series E-Fence
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>