ventair SPYEC1253WH Blade Ceiling Sweep Fan Instruction Manual

ventair SPYEC1253WH Blade Ceiling Sweep Fan

Thank you for purchasing this quality Ventair ceiling fan.
Please read all instructions carefully to ensure correct installation, and operation.
Note: Keep this manual for future reference.

SAFETY PRECAUTION:

1. To Ensure a Safe, and successful installation, refer to, and follow, all instructions and diagrams.
2. All electrical work should only commence after disconnection of the power. Remove fuses or turn off the circuit breaker to ensure all pole isolation of the electrical supply.
3. Make sure that your installation site will not allow the rotating fan blades to come in contact with any object and that there is a minimum clearance of 300mm from the blade tip to the wall or ceiling. Please note that the greater the clearance around the fan, the better the airflow will be.
4. The fixing point for the fan must be able to support the weight of 4 times that of the net weight of the fan. Net weights can be found on the next page. If you are mounting the fan to a ceiling junction box, the box and fixing must be able to support the moving weight of the fan and must not twist or work loose.
5. The fan must be earthed.
6. It is not recommended that ceiling fans and gas appliances be operated in the same room at the same time.
7. Do not insert anything into the fan blades while the fan is operating. This will damage the blades and upset the balance of the unit causing the unit to wobble.
8. Once fully installed, double check that all connections are secured and tightened before operating.
9. Because of the fan’s natural movement, some connections may loosen over time. Check the support connections, brackets and blade attachments twice a year, adjust/gently tighten as necessary.
10. Always have your fan installed by a licensed electrician.
11. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
12. Children should be supervised to ensure that they do not play with the appliance.
13. The fan is to be installed so that the blades are at least 2.1m or more above the floor.

This product is suitable for use in Tropical climate areas.
The Fan may be used indoors, covered outdoors and is ideal for commercial applications.

SPECIFICATION

PARTS LIST

Unpack the fan and carefully identify the parts.
NOTE: Check for any damage prior to installation. Any Damage, marks or scratches are not covered by In-Home warranty and should be returned to place of purchase for a replacement.

INSTALLING

INSTALLING MOUNTING BRACKET

1. Before installation, make sure that the blade tips will not be within 300mm of any object or fixture.

2. Using screws provided ,secure the hanging bracket to a ceiling joist or suitable structure
   that is capable of supporting at least four times the actual weight of the fan (see Specifications) Note : For structures that are not Wooden , please use the appropriate fixing screws or bolts to suit.

3. Connect safety cable to bracket.

Mounting Plate Hanging System

1. Ceiling Joist
2. Canopy
3. Terminal Block and Mounting Plate
4. Earth Wire
5. Hanger Ball
6. Down rod
7. Safety steel wire (to be fixed on the bracket via the screw)

Please use the fixing screws provided. Use of non certified fixing screws may void the warranty.

INSTALLING BLADES

• Slide the ‘Lower canopy’ upwards and move ‘motor cover plate’ to the side.
• Slide ‘Blades into postion and attach gently using screws provided.
• Clip ‘motor cover plate’ into position making sure the tabs cover the blade joints.
• Slide Lower canopy into position ensuring it does not touch any spinning part of the fan. Your fan is now ready to hang.

WIRING AND ELECTRICAL CONNECTIONS.

WARINING : FOR YOUR SAFETY, ENSURE THE MAINS SUPPLY IS SWITCHED OFF TO THE WIRING CIRCUIT BEFORE PERFORMING ANY ELECTRICALTASKS.
Each Fan must have A ‘localised single pole isolation switch’ as indicated in the diagram.
Do not use any other style/type or brand of speed controller for this Fan.

• Step 1: Connect the EARTH wire to the terminal port marked “”on the terminal block mounting bracket.
• Step 2 Connect the supply LIVE wire to Localized single pole switch and then wire to terminal port marked “L”on the terminal block mounting bracket.
• Step 3: Connect the supply Neutral wire to the terminal port marked “N” on the terminal block mounting bracket

HANGING THE FAN

Hang the assembled fan into the Hanging Bracket making sure the groove on the hanging Ball, locates into the Tab of the Hanging Bracket.

FOR RAKED/SLOPED CEILINGS

1. Ensure the fixing tab fits in the groove of the hanger ball.
2. Ensure the fixing tab is set at the highest point.
3. Suitable for installations up to 18 Degrees of Pitch.

INSTALLING REMOTE RECEIVER

1. “Clip receiver into position on centre strut of hanging bracket”
2. Connect receiver using quick connect terminals to fan wire terminals.

INSTALLING THE UPPER CANOPY

• Align screws on hang  Bracket with keyholes in ‘upper canopy’ and twist clockwise into position.
• Tighten screws gently and ensure there is a uniform 5mm (approx) gap between ceiling and canopy.
• Clip ‘decorative screw cover’ into place.

Once all the above steps have been followed, you are now ready to restore the mains power supply.
Make sure there is nobody near or under the fan, then turn ON the fan (and light switch if included in your model) to test.

REMOTE INSTRUCTIONS

Using remote Control

1. Turn the fan “OFF” only.

2. Adjust the fan speed from 1 (low) to 6 (high)

3. Creates a natural Breeze effect.

4. Light ON/OFF.

5. Forward / Reverse alters the direction of blade rotation. (Summer / Winter)

6. Adjust Light colour (Cool, Natural and Warm)

7. Press and hold to adjust the Light intensity up or down.
   A ‘ Beep ‘ will be heard at both Minimum, and Maximum brightness. Release, then press again to reverse the dimming direction.

8. One, two and 4 hours run-on Timer

The remote handpiece comes factory paired with the remote receiver, but if you wish to pair a remote handpiece to multiple fans

• Step 1: Turn “OFF” isolation switch.
• Step 2: Turn “ON” isolation switch and within 2 seconds, press fan off button for 3-4 second until a “Beep-Beep” sound is heard. (Repeat steps above if not successful)

APP Wi-Fi CONTROL INSTRUCTIONS

Note: Ensure Remote control is paired to fan ( press and hold Fan off 2-3 sec, the fan will emit one beep)

1. Download the ” Tuya Smart ” app. Scan the QR code or download from Apple Store (IOS) or Google Play (Android) .

2. Register/sign up your Tuya smart (or Smart Life) account. Follow the prompts using a choice of either mobile phone number or email address.

3. Turn on Wi-Fi on your mobile phone and ensure fan is in the same Wi-Fi area.

4. Open your Tuya Smart App and choose add device

5. Choose ‘Small Home Appliances’ then choose ‘Fan (Wi-Fi)’ .

6. Select a 2.4GHz Wi-Fi network and enter password. (if your Wi-Fi is 5GHz,it should also display a 2.4GHz version as a Wi-Fi
   option available) please set to the 2.4GHz option. Select ‘Next’.

7. Reset the Fan, ready for pairing/syncing.
   Note: this product does not have an indicator light. Please follow resetting instructions listed below.

   • Turn isolation switch(found on the wall in same room as fan) to “OFF” for at least 15 seconds. Then, turn isolation switch to ‘ON’ the fan will emit one beep, and ‘within 10 seconds’ press and hold the F/R F R BUTTON on the fan remote (3-5 sec).
   • The SPYDA EC fan will emit a “beep-beep-beep” (3 x beeps) sound to indicate that your fan is ready to be paired with your Tuya Smart App.

8. Select, “confirm the indicator is rapidly”.
   Then continue with Select “blink quickly” to begin the pairing procedure.
   This product does not have an indicator light, but these directions must still be followed for successful pairing. Note: Please complete the pairing procedure within 3 minutes of resetting.

9. Your SPYDA EC fan now has been added to your Tuya Smart (or Smart Life) account.
   If it is failed, repeat steps 6 to 8 until you see this interface

Please Note : a single fan can be linked to many phones as long as they are using the same tuya or Smartlife account.
Controls
You can control some basic functions from the home screen.
Or click on the fan to access the main control panel for full list of control functions

MAINTENANCE AND TROUBLESHOOTING

• Keep the fan clean. Wipe away dirt with a clean soft cloth, ordinary soap and water, wipe dry. Do not use solvents, etc. (Gasoline or petroleum.)
• Make sure to disconnect the power supply before cleaning and maintenance is carried out.
• Ensure that the fan is switched off from the supply mains before removing the guard.

The points described below should be checked, and corrected if necessary, upon installation and at least once a year thereafter.
Excessive movement and wobbling?

• Check all screws, bolts and nuts are secured tightly.
• Change position of the blades.
• Check blade height. Carefully rotate the fan and measure each blade from a fixed point on the ceiling. (Adjust if necessary, by loosening and re tightening the upper or lower blade screws)

Does the motor, down rod or other components shake or vibrate abnormally?
Shaking and abnormal vibration can be caused if the blade holding screws or screws for the suspended parts are loose, or if a blade is deformed. If a blade is deformed, all 3 (or 4) blades should be replaced as a set.
Is there any unusual noise?
Is the ‘Lower Canopy touching the spinning parts? (adjust as required)
Is the ‘upper canopy ‘in contact with ceiling surface?
Night Noise:
This is the biggest cause for service calls, which are outside the manufacturer’s warranty. If a fan has a fault, it will always be noticeable. even during the day.
Naturally when everything is quiet at night, you will be more inclined to hear small noises, which may not be noticeable at other times. Blades spinning, may cause a slight chopping sound which is more pronounced at higher speeds. This is normal and is an indicator of high air movement.
WARNING:
If at any stage the fan develops excessive wobbling or unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent or suit ably qualified persons.
Fan Light:
Except for an actual fault in manufacturing, which is extremely rare, noises and vibrations are often more accentuated when a fan light is fitted. For instance, a fan light diffuser that has not been tightened or worked loose can cause a rattle Frequent care and maintenance will reduce this.
Do not dispose of electrical products with household waste. Please check with your local council for advice on disposal or recycling. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.
4 CAPITAL PLACE
CARRUM DOWNS VIC 3201
PHONE: (03) 9775 0556
FAX: (03) 9775 0775

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>