Inrico B05 Wireless RSM User Guide

Inrico B05 Wireless RSM

Product Information

Specifications:

• Manufacturer: Inrico Technologies Co.,Ltd.
• Transmitter Frequency:
  • BT: 2402-2480MHz
  • BLE: 2402-2480MHz
• Receiver Frequency:
  • BT: 2402-2480MHz
  • BLE: 2402-2480MHz
  • NFC: 13.56MHz
• RF-Output Power:
  • BT: 8.58dBm ERP/EIRP/Conducted
  • BLE: 7.95dBm

Product Usage Instructions

Safety Precautions:

Before using the product, ensure you read and understand all safety instructions provided in the user manual.

Power On/Off:

To power on the device, press and hold the designated power button for 3 seconds. To power off, repeat the same process.

Connectivity:

Follow the user manual to establish Bluetooth (BT) or Bluetooth Low Energy (BLE) connections as needed for your device.

NFC Usage:

To utilize NFC functionality, ensure NFC is enabled on both devices, then bring them in close proximity to establish a connection.

Maintenance:

Regularly clean the device with a soft, dry cloth. Avoid using harsh chemicals or solvents that may damage the product.

FAQ

• Q: How do I reset the device?
  • A: To reset the device, locate the reset button and press it for 10 seconds until the device restarts.
• Q: Can I charge the device while using it?
  • A: Yes, you can charge the device while using it. Ensure you use the provided charging cable and a compatible power source.

Please read this instruction book carefully before using and keep this with care.

www.inricosolutions.com

Notes Before Using

Please read the following content carefully. It is very important for radio users to gain general knowledge and risks.

• Do not use the device or charge the battery in any hazardous areas such as gas, dust, steam, etc.
• Please turn off the device while refueling or parking at the gas station.
• Do not disassemble your radio.
• Avoid prolonged time in the sun or placing it near a heating appliance.
• Avoid excessive exposure to the extremely dusty, damp, and splashing place, or leave it on an unstable surface.
• Reparation by professional technicians, do not disassemble by yourself.

Disclaimer

Inrico reserves the right to modify product design and specifications. Inrico assumes no responsibility in the event of printing errors. All specifications are subject to change without notice.

Unpacking and Device Checking

Please unpack and take out the device and all accessories carefully, and ensure all lists have been gotten before discarding the cardboard box. If any items are lost or damaged in transit, please contact with our distributors.

Accessories

Handling Precautions

• Do not overcharge the battery Please stop charging if it can’t be fully charged within the required time. The battery probably overheats, smokes,  bursts or suddenly be on fire due to an abnormal charging process. When fully charged or not charged, please disconnect the charger and unplug it from the power outlet.
• Do not discard the battery in a microwave or high-pressure container. The battery probably overheats, smokes, bursts or suddenly be on fire.
• Do not expose the damaged battery near any fire. If the battery is broken, leaking or has an abnormal odor, please remove it from flammable areas immediately. The fluid in the battery is flammable, which may cause smoke and fire.
• Do not use an abnormal battery If the battery is with odd smelly, discolored, deformed, etc., please stop charging or disassemble from the device immediately.
• Please use an authorized power adaptor To comply with warranty terms and avoid damages, charge the battery using a specified charger for best performance.
• Please do not charge at high or low temperature

Battery Care

Fully Charge the Battery Before Initial Use

• Do preserve battery life by switching off a device and removing the batteries when it’s not being used and is not expected to be used for extended periods of time.
• Do practice proper battery storage by keeping batteries in a cool, dry place at normal room temperature.

Properly Store Batteries

• Remove the battery from the device.
• Charge and discharge the battery to 40%-65% if it will not be used for 10 days or more. This can greatly extend the battery life.
• The battery should drop below 65% when it is idle for more than 10 days to prevent it from swelling.
• Store the battery in a cool and dry environment that’s less than 25°C.

Features of Lithium Battery

• Battery capacity will reduce after multiple charging cycles.
• The battery capacity drops gradually even without being used.
• Longer charging time is required in shady places.
• Charging and storing lithium batteries in warm conditions will shorten their lifespan. Please do not leave them inside the vehicle or near the heater.
• If the battery working time has reduced significantly, please replace the battery immediately in avoid of fluid leakage.

Clean and Maintenance

• Before cleaning and maintaining the device: please stop running, turn off the device, and disconnect all connections with other equipment.
• When you do not use the radio, please cover the accessories connector.
• When cleaning the dust, please use soft brush and neutral detergent (no strong corrosive chemicals) to wipe it.
• Please keep the equipment and accessories dry.
• Please do not use the microwave oven or hair dryer or other heating devices to dry them.

Product Overview

Functions Sheet

power off state
Power off| Press and hold for 2 seconds in power on state
Music pause/play| Short press to pause music playback, short press again to continue playing
Answer calls| Short press once to answer an incoming call
Hang up calls| Short press once to hang up in call status
Reject calls| Short press twice in succession during an incoming call
2| PTT button| Push to talk
__ 3| __ Customizable button Fl| Short press: Customize Long press: Customize
__ 5| __ OK button (Customizable)| Short press: Customize Long press: Customize
6| __ Up button (Customizable)| Short press: Customize Long press: Customize
7| __ Down button (Customizable)| Short press: Customize Long press: Customize
8| __ Disconnect/ Reconnect button| Short press: Reconnect the last connected device

Long press: Disconnect the current Bluetooth connection

11| sos| Short press: Customize Long press: Customize
14| Volume+| Short press: Customize

Long press: Customize

__**15| __** Volume-| Short press: Customize Long press: Customize

Note: PTT intercom cannot be enabled when using the shoulder microphone key to connect to PC data, and reception is not affected

Accessories Installation

Attaching the Battery

(a) Align the electrical contact of the battery with the bottom rails.
(b) Press the battery firmly, and make sure the electrical connection touches with the bottom.

Attaching the Battery Cover

(a) Close the battery cover
(b) Press the two-layer battery cover
(c) Fasten the two screws

Install the belt clip

Push the belt clip along the “T” slot to the bottom.

Remove the belt clip

Lift the buckle and pull the belt clip upward.

Install Hand Strip

Status Indicators

Function Operation

Call Handling

When there is an incoming call to the RSM, short press the on/off button to answer the call when the shoulder microphone is connected.

Reject Calls

When the RSM has an incoming call, double-press the switch button to reject the call.

Hang up Calls

Click the on/off button to hang up while on a call.

Music Pause/Play

When the RSM-connected device plays music, short press the on/off button to play or pause.

Standby

When the RSM is in the pending pairing state, after 15 minutes without connecting Bluetooth, the system will automatically shut down.

PTT Function

RSM supports terminal equipment intercom software, terminal equipment and RSM Bluetooth connection can achieve PTT function through the PTT button.

NFC Connection

When the RSM is in a state of pending pairing, use the relevant NFC device to perform NFC sensing and Bluetooth connection.

Body QR Code

Information can be read using related device scanning

Simple Troubleshooting

install the battery.

•   The battery may be out of power. Charge or replace the battery.

•   The battery may be in poor contact due to dirt or damage. Clean the electrical contact or replace it.

__ Terminal Crash| __ •   Due to high-strength radio frequency interference, such as being close to high-power TV transmission towers, GSM base stations or airports
Buttons Not Working| •   The buttons may not work temporarily, restart the terminal.

•   The buttons are broken, contact the dealer or our company.

Echo or Noise During Connecting| __ •  The speaker may be covered, clean the speaker surface.
Shorter Standby Time| •  The battery life becomes shorter in high-temperature environments. Replace a new qualified battery.

•  Power consumption increased in areas with weak signal. Please temporarily turn off the device.

Can’t Connect to Bluetooth| __ •  The device cannot work properly or cannot be used. Please confirm whether the device is turned on.

•  Confirm whether the device and terminal are paired successfully.

__ Disconnected from

Terminal Device

| •  Check whether the battery is too low and whether the distance between the microphone and the terminal device is within 10 meters, Or whether there are dry shielding obstacles in the middle, etc.

Specification

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be  determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

For CE

A1703, Shenzhen National Engineering Laboratory Building, No. 20 Gaoxin South 7th

Road, Shenzhen,China

Transmitter Frequency:| BT: 2402-2480MHz

BLE: 2402-2480MHz

Receiver Frequency:| BT: 2402-2480MHz

BLE: 2402-2480MHz NFC: 13.56MHz

RF-Output Power: ERP/EIRP/Conducted| BT: 8.58dBm

BLE: 7.95dBm

Please read this instruction book carefully before using and keep this with care.
www.inricosolutions.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>