eurolite DMF-5 LED Hybrid Flower Effect User Manual

: June 9, 2024
: eurolite

Table of Contents

DMF-5 LED Hybrid Flower Effect
INTRODUCTION
SAFETY INSTRUCTIONS
DESCRIPTION OF THE DEVICE
INSTALLATION
CONNECTIONS
OPERATION
CLEANING AND MAINTENANCE
PROTECTING THE ENVIRONMENT
TECHNICAL SPECIFICATIONS
Accessories
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

LED DMF-5
Hybrid Flower Effect

User manual
LED DMF-5 Hybrid Flower Effect
Effect spotlight with flower- and backlights effect, incl. IR remote control No. 51918564
www.eurolite.de

DMF-5 LED Hybrid Flower Effect

This user manual is valid for the article number: 51918564
You can find the latest update of this user manual in the Internet under: www.eurolite.de

DANGER! Electric shock caused by short-circuit
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires. Never open the housing. Keep the device away from rain and moisture.
Please read these instructions carefully before using the product. They contain important information for the correct use of the product.

Every person involved with the installation, operation and maintenance of this device has to

be qualified
follow the instructions of this manual
consider this manual to be part of the total product
keep this manual for the entire service life of the product
pass this manual on to every further owner or user of the product
download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen one of our products. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.

Product features
Effect spotlight with flower and blacklight effect, incl. IR remote control

Equipped with twelve 3 W LEDs, 2 each in the colors red, green, blue, white, amber and pink for colorful flower effects and eight 3 W LEDs in UV for dynamic blacklight effects
Ultra-light, ideally suited for mobile use
Auto, music, master/slave and DMX mode
Three built-in auto and music show programs
Direct color selection for 20 preset colors
Addressing and setting via control panel with 4-digit LED display
Convenient wireless control via included IR remote control EUROLITE IR-7
Sound-control via built-in microphone with adjustable microphone sensitivity
Swivel mounting bracket
Supports QuickDMX – the wireless DMX system from Eurolite
Compatible with CRMX by LumenRadio und WDMX by Wireless Solution
Built-in phantom-powered USB port for QuickDMX, CRMX and WDMX receivers (optional)
Switch-mode power supply for operation between 100 and 240 volts
IEC terminals for power linking up to 8 units
Can be operated in 6; 11 CH mode
The device is cooled by passive convection
Flicker-free projection

SAFETY INSTRUCTIONS

WARNING!
Please read the safety warnings carefully and only use the product as describe in this manual to avoid accidental injury or damage.

Intended use

This device is an LED projector for creating decorative lighting effects. This device is designed for professional use in the field of event technology, e.g. on stage. It is not suitable for household lighting.
Only use the device according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
We do not assume any liability for material and personal damage caused by improper use or noncompliance with the safety instructions. In such cases, the warranty/guarantee will be null and void.
Unauthorized rebuilds or modifications of the device are not permitted for reasons of safety and render the warranty invalid.

Danger due to electricity

The device is suitable for indoor use only. Do not use it outdoors. Never expose it to rain or moisture. Do not store it in rooms exposed to moisture.
To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the device.
Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must be exactly the same as stated on the device. If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never defeat the protective ground of a mains cable. Failure to do so could result in damage to the device and possibly injure the user.
The mains outlet must be easily accessible so that you can unplug the device quickly if need be.
Never touch the mains plug with wet or damp hands. There is the risk of potentially fatal electric shock.
The mains cable must not be bent or squeezed. Keep it away from hot surfaces or sharp edges.
Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the plug.
Unplug the device during lighting storms, when unused for long periods of time or before cleaning.
Do not expose the device to any high temperatures, direct sunlight, dripping or splashing water, strong vibrations or heavy mechanical stress.
Do not place any objects filled with liquids on the device.
Do not place any open sources of fire, such as burning candles, on or directly next to the device.
Make sure that objects cannot fall into the device, in particular metal parts.
Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, liquid has been spilled or objects have fallen into the device; when the device has been exposed to rain or moisture, has been dropped or malfunctions occur.
Cleaning of the device is limited to the surface. Make sure that moisture does not come into contact with any areas of the terminal connections or mains voltage control parts. Only wipe off the product with a soft lint-free and moistened cloth. Never use solvents or aggressive detergents.

Danger to children and people with restricted abilities

This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. Never leave this device running unattended.
This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Warning risk of burns and fire

The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature range.
The housing temperature (Tc) can be up to 55°C during use. Avoid contact by persons and materials.
Do not illuminate surfaces within 10 cm of the device. This value is indicated on the device by the – – -m symbol.
Do not use the device near highly flammable materials. Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around the device. Never cover the air vents of the housing.

Warning risk of injuries

Do not look directly at the light source. Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
Make sure that the product is set up or installed safely and expertly and prevented from falling down. Comply with the standards and rules that apply in your country, in particular EN 60598-2-17.
If you lack the qualification, do not attempt the installation yourself, but instead use a professional installer.
Improper installation can result in bodily injury and or damage to property.
The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions.
For overhead use, always secure the device with a secondary safety attachment such as a safety bond or safety net.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the device.
For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all times.

Caution material damage

This device must not be connected to the mains voltage by means of a dimmer.
Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
Never switch the device on and off at short intervals. This will considerably reduce the service life of the device.
If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has evaporated.
Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
If a serial number label is affixed to the device, do not remove the label as this would make the guarantee void.

About batteries

Do not try to short-circuit, recharge, disassemble or heat batteries (danger of explosion!).
Remove the batteries if the device is not used for a longer period of time.
Damaged/leaking batteries may cause harm to your skinuse safety gloves.

DESCRIPTION OF THE DEVICE

(1) R, G, B, W, A, P 3 W LEDs for flower effect
(2) 3 W LED UV, for blacklight effect| (3) Infrared sensor for the remote control
(4) Mounting bracket
(5) Fixation screw
---|---

(6) Power out
(7) LED display with operating buttons
(8) Microphone
(9) USB port for QuickDMX wireless receiver| (10) Safety eyelet
(11) Fuse holder
(12) Power in
(13) DMX-output
(14) DMX-input
---|---

INSTALLATION

WARNING! Risk of injury caused by falling objects
Devices in overhead installations may cause severe injuries when crashing down. Make sure that the device is installed securely and cannot fall down. The installation must be carried out by a specialist who is familiar with the hazards and the relevant regulations.
The device may be placed on the floor or fastened to a truss or similar rigging structure. The device must never be fixed swinging freely in the room.

The rigging structure must support at least 10 times the weight of all fixtures to be installed on it.
Block access below the work area and work from a stable platform when installing the device.
Use rigging hardware that is compatible with the structure and capable of bearing the weight of the device. Please refer to the “Accessories” section for a list of suitable rigging hardware.
Secure the device with a safety bond or other secondary attachment. This secondary safety attachment must be sufficiently dimensioned in accordance with the latest industrial safety regulations and constructed in a way that no part of the installation can fall down if the main attachment fails. An appropriate eyelet is mounted on the device for fixation of the safety bond. Fasten the safety bond in such a way that, in the event of a fall, the maximum drop distance of the device will not exceed 20 cm.
To align the device, release the fixation screws at the mounting bracket, adjust the desired inclination angle and tighten the fixation screws.
After installation, the device requires inspections periodically to prevent the possibility of corrosion, deformation and looseness.

CONNECTIONS

The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts.

Connect the device via the mains cable to a grounded mains socket. Thus the unit is switched on.
To switch off the unit, disconnect the power plug.
Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.
The jack POWER OUT allows for power supply of further devices. To interconnect several devices, connect the jack POWER OUT to the input POWER IN of the next unit until all units are connected.
Matching power cables are available as accessories. In this manner, up to 8 devices can be linked at 230/240 input voltage and up to 4 devices at 110/115 input voltage.

DMX512 control

A DMX512 data link is required in order to control the device via DMX. The device provides 3-pin XLR connectors for DMX connection.

Connect the output of your DMX controller to the DMX input DMX IN of the device with a DMX cable.
Connect the DMX output DMX OUT of the device to the DMX input of the next unit in the chain. Always connect one output to the input of the next unit until all units are connected.
At the last unit, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between
Signal (–) and Signal (+) in the DMX output of the last unit.
If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended to insert a DMX level amplifier to ensure proper data transmission.

XLR connection:

Wireless DMX transmission with QuickDMX
The device features an alternative DMX input for a QuickDMX receiver (sold separately). CRMX and WDMX receivers are compatible and can also be used. The connector allows a DMX control signal to be transmitted wirelessly to the device, eliminating the need for complex wiring to the DMX controller. The connector is designed as a USB port which provides the required 5 V operating voltage for the receiver.

Occupation of the USB port:

OPERATION

After connecting the device to the mains it is ready for operation. The display indicates the last operating mode. The operating modes can be selected by means of the display and the control buttons. All settings remain stored even if the device is disconnected from the mains. The device can be operated in stand-alone mode via the control board and the EUROLITE IR-7 remote control or in DMX-controlled mode via any commercial DMX controller.

Menu structure

Mode	Display	Function
DMX channel	Addr	6CH

Stand-alone mode

Preset colors
In the Stat mode the device will constantly emit one of 20 preset colors or color combinations.

Press the MENU button so many times until Stat is indicated in the display. Confirm with the ENTER button.
Use the buttons UP and DOWN to adjust the desired color or colors combinations. Confirm with the ENTER button.

Automatic mode
In automatic mode, 3 show programs are available that run at an adjustable speed.

Press the MENU button so many times until Auto is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to select the desired show program (Au 1 – Au 3). Confirm with the ENTER button.
Press the MENU button so many times until SPEE is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to adjust the running speed of the program from SP 1 (slow) to SP 9 (fast). Confirm with the ENTER button.

Sound control
Via the integrated microphone the unit can perfectly reproduce the show programs to the rhythm of the music (sufficient bass provided).

Press the MENU button so many times until Soun is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to select the desired show program (So 1 – So 3). Confirm with the ENTER button.
Press the MENU button so many times until SEnS is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to Adjust the microphone sensitivity to the volume of the music (SE 1 = low, SE 9 = high).
Press the MENU button so many times until SPEE is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to adjust the running speed of the program from SP 1 (slow) to SP 9 (fast). Confirm with the ENTER button.
If you enable the silent scene mode (on setting) in menu item SILE, the LEDs will be switched off if the volume is too low or if there is no sufficient bass beat. If you disable this mode (off setting) the LEDs remain on during periods without music.

Total brightness
Menu diMM allows adjusting the total brightness for all stand-alone operating modes: Stat, Auto and Soun.

Press the MENU button so many times until diMM is indicated in the display. Confirm with the ENTER button.
Use the buttons UP and DOWN to adjust the desired brightness (dI 1 = dark, dI 9 = bright). Confirm with the ENTER button.

Behavior at missing DMX-signal
In DMX lost mode the program offers different options when no DMX signal is received.

Press the MENU button repeatedly until the display shows the DMX lost menu. Press ENTER to confirm.
Select the desired program with the UP and DOWN buttons (see Menu structure). Confirm with ENTER.

Interconnecting several devices (master/slave operation)
Several devices may be interconnected (max. 32). Then all slave units can be synchronized and controlled with the master unit without the need for a DMX controller. The devices must be set to the corresponding operating modes.

Configure all slave units before connecting the master unit: Press the MENU button so many times until SLAU is indicated on the display. Confirm with the ENTER button.
Connect the DMX output of the master unit to the DMX input of the first slave unit. Then connect the DMX output of the first slave unit to the DMX input of the second slave unit, etc. until all units have been connected in a chain. Make sure the master unit is the first in the chain. Do not connect a DMX controller to the DMX input of the master unit.
Set the master unit to the desired operating mode. The interconnected devices will now operate synchronously.

Remote control IR-7
The device must be activated for remote control. For this, set menu item InFr to on. When actuating a button, always direct the remote control towards the sensor. There must be no obstacles between remote control and the sensor.

Button	Function
BLACKOUT	LEDs off
AUTO	Automatic mode; program selection with (+)/(-)
SOUND	Sound control; program selection with (+)/(-)
STROBE	Strobe effect for automatic mode and sound control; flash rate setting

with (+)/(-)
SPEED| Running speed in automatic mode and sound control; setting with (+)/(-)
SENSITIVITY| Microphone sensitivity; setting with (+)/(-)
DMX| DMX mode
MANUAL| Color mode; select colors with R/G/B/W/A/P and 0 Setting with (+)/(-);
1-9| Total brightness; 1 = dark, 9 = bright

Notes:

The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote control. Otherwise operation of the remote control is not possible.
If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control press the small bar with the groove to the right and at the same time remove the battery support. For operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the button cell shows upwards in the support.
Remove the battery from the remote control as a precaution if the device is not used for a longer period of time.

DMX operation
Setting the number of DMX channels and the DMX starting address
For operation with a controller with DMX512 protocol, the device is equipped with 11 control channels.
However, it can also be switched to a mode with 6 channels if different functions are required. To be able to operate the device with a DMX controller, the DMX starting address must be set. The starting address depends upon which DMX controller is being used. Please refer to the controller’s documentation.

Press the MENU button so many times until Addr is indicated in the display. Confirm with the ENTER button.
The display indicates 6 CH (6 DMX channels) or 11 CH (11 DMX channels). Use the buttons UP and DOWN to select the desired DMX channel mode. Confirm with the ENTER button.
Now the display indicates the menu item for the DMX starting address d***. Use the buttons UP and DOWN to set the address. Confirm with the ENTER button.
The display will not flash when DMX signals are being received. If no control signals are available, the display will flash.

Note: Please make sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX chain. If several devices are addressed similarly, they will work synchronically.

Functions in DMX mode
6-Channel-mode

Channel	Value	Function
CH 1 Master-Dimmer	000 — 255	Total brightness (0-100%)

11-Channel-mode

Channel	Value	Function
CH 1 Master-Dimmer	000 — 255	Total brightness 0-100%
CH 2 Strobe Flower- LEDs	000 — 009	No function
010 — 255	Strobe with increasing speed (0-100%)
CH 3 Red	000 — 255	Brightness (0-100%)
CH 4 Green	000 — 255	Brightness (0-100%)
CH 5 Blue	000 — 255	Brightness (0-100%)
CH 6 White	000 — 255	Brightness (0-100%)
CH 7 Amber	000 — 255	Brightness (0-100%)
CH 8 Pink	000 — 255	Brightness (0-100%)

CLEANING AND MAINTENANCE

The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lenses, in particular, should be clean to ensure that light will be emitted at maximum brightness.

Disconnect the device from power and allow it to cool before cleaning.
Clean the surface with a soft lint-free and moistened cloth. Never use alcohol or solvents as these may damage the surface. Make sure that no liquids can enter the device.
The device must be dry before reapplying power.

There are no serviceable parts inside. Do not open the housing. Do not try to repair the device by yourself as this may result in damage. Maintenance and service operations are only to be carried out by authorized dealers. Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer.

Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

Disconnect the device from power and allow it to cool.
Open the fuse holder of the mains connection with a fitting screwdriver.
Remove the old fuse from the fuse holder and replace it with a new fuse.
Carefully push the fuse holder back into its position before reapplying power.

PROTECTING THE ENVIRONMENT

Disposal of old equipment
When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product.
**** You as the end user are required by law (Battery Ordinance) to return all used batteries/ rechargeable batteries. Disposing of them in the household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly, you contribute to the protection of the environment.

TECHNICAL SPECIFICATIONS

Power supply:	100-240 V AC, 50160 Hz
Power consumption:	24 W
IP classification:	IP20
Protection class:	Class I
Power connection:	Mains input IEC connector (M) mounting version Power supply

cord with safety plug (provided)
Power output:| IEC connector (F) mounting version
Fuse:| 5 x 20 mm, T 0.5 A fuse replaceable
Lamp type:| LED lamp
LED:| 12 x high-power 3 W R, G, B, W, A, P
8 x high-power 3 W ultra violet (UV)
DMX channels:| 6; 11
DMX input:| 3-pin XLR (M) mounting version
DMX output:| 3-pin XLR (F) mounting version
Cooling:| Passive convection
Control:| Stand-alone; IR remote control; DMX; Master/slave function; Sound to light via Microphone; QuickDMX (optional); W-DMX by wireless solution via USB (optional); CRMX by LumenRadio via USB (optional)
Beam angle (1/2 peak):| Multi beam effect 120°
Housing color:| Black
Display type:| 4 digits 7-segment LED display
Dimensions:| Width: 36.0 cm
Depth: 9.0 cm
Height: 15.0 cm
Weight:| 1.3 kg
Remote control|
---|---
Battery:| 1 x Button cell 3.0 V CR2025 lithium manganese (provided)

Accessories

EUROLITE TPC-10 Coupler, silver	No. 59006856
EUROLITE Safety Bond A 4x1000mm up to 15kg silver	No. 58010320
EUROLITE QuickDMX USB Wireless Transmitter/Receiver	No. 70064704
EUROLITE DMX cable XLR 3pin 3m black	No. 3022785H
PSSO DMX cable XLR 3pin 3m black Neutrik	No. 30227810
EUROLITE IR-7 Remote Control	No. 50530561

All information is subject to change without prior notice. © 01.03.2022

Eurolite is a brand of Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5 97297 Waldbüttelbrunn Germany
D00113216 Version 1.0 Publ. 01/03/2022
00137809.DOCX, Version 1.0