AUSSIE TRAVELLER 40600000002000 Drop Down Single and Double Manual Steps Installation Guide
- June 4, 2024
- AUSSIE TRAVELLER
Table of Contents
40600000002000 Drop Down Single and Double Manual Steps
Installation Guide
Read
this installation instruction thoroughly. Incorrect installation or operation
may void any warranty. Incorrect use or operation may cause serious injury.
PRODUCT INTRODUCTION
The Aussie Traveller range of folding manual single and double drop-down steps are designed to be used as high-quality equipment which can help passengers get into a full range of Recreational Vehicles, including Caravans, Campers, Motorhomes, and Emergency Vehicles. Ask Aussie Traveller about the full range of RV steps available.
DESCRIPTION:
- The manually operated drop-down step function provides safe access to recreational vehicles by reducing entrance step heights.
- Easy to install.
- Simple pull-out and push-in operation.
| MODEL | DRIVE MODE | PLATFORM SIZE (L×W) | WEIGHT |
|---|---|---|---|
| Single Step | Manual | 510 × 240mm | 5kg |
| Double Step | Manual | 510wwv × 200mm | 7.5kg |
STANDARD PACKING LIST:
1 × Manual Folding Step
1 × Mounting Kit – includes 4 bolts, washers & nuts.
1 × User Manual
INSTALLATION
REQUIREMENTS:
Please refer to ADR58 / EN 1645-1 (caravans) requirements, for the correct
installation of an RV Manual or Electric step.
INSTALLATION OF THE AUSSIE TRAVELLER DROP-DOWN STEP:
It is recommended that the installation instructions are followed. Depending on the vehicle type, the installation requirements may vary. Various mounting attachments/installations are listed below:
- Right through the vehicle bottom/footwell.
- In rails incorporated in the chassis.
- In a special construction welded or bolted to the chassis.
NOTE: Depending on the specific installation, the position of the steps and specific installation process may change.
-
Prior to commencing the installation of the step, ensure that there are no obstacles on the inside (for example electric cables, gas pipes, and so on) of the mounting plates or
within close vicinity. -
Drill four 9mm holes according to the positions shown in the dimensions drawing. On the mounting brackets on both sides, position the step evenly so the step platform is
perfectly level (horizontally) and is positioned evenly on the rails so the step will ‘pull out’ evenly (no rotation left or right). When retracted, the step will be approx. 42mm outside the frame. Install bolts, washers, and nuts as shown and tighten. DO NOT overtighten nuts. -
Ensure that prior to and at the conclusion of the installation, there are no hazards that could potentially injure or harm in any way. Ensure there are no clamping dangers (hands, fingers, feet, toes, etc.) when the step is extended or retracted. Never use the step in a way that the product is not intended.
-
Never attempt to open or close the step while it is in use.
-
Install the Aussie Traveller Step so that it can be dismounted easily.
NOTE: Maximum height from ground to bottom step is 400mm. Install the step
so it is between 200-300mm from the top of the step to the base of your
vehicle.
TECHNICAL PARAMETERS – DROP-DOWN STEP SINGLE
TECHNICAL PARAMETERS – DROP-DOWN STEP DOUBLE
OPERATING THE MANUAL DROP-DOWN STEP
-
To open, pull the step slightly upward and outward simultaneously until the step is fully engaged. Ensure the step is has been fully opened and is stable and secure prior to
stepping on the platform. -
To close, pull the step slightly upwards and push back simultaneously until the step is fully closed. Ensure the step is has been fully closed and is stable and secure before
any travel is commenced. For closure, this function can be performed using a foot.
NEVER USE THE STEP IF STOWED OR ONLY PARTIALLY DEPLOYED.
1300 663 868
enquiries@aussietraveller.com.au
aussietraveller.com.au
BRISBANE SHOWROOM: 11-15 Oasis Court, Clontarf QLD 4019
MELBOURNE SHOWROOM: 235 Barry Road, Campbellfield VIC 3061
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>