TRISTAR KA-5075 2000 Watt Electric Heater Instruction Manual

TRISTAR KA-5075 2000 Watt Electric Heater

SAFETY

• By ignoring the safety instructions the manufacturer cannot be held responsible for the damage.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Never move the appliance by pulling the cord and make sure the cord cannot become entangled.
• This appliance is only to be used for household purposes and only for the purpose, it is made for.
• This appliance shall not be used by children aged less than 8 years. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Keep the appliance and its cord out of reach of children aged less than 8 years. Cleaning and user maintenance shall not be made by children unless older than 8 and supervised.
• To protect yourself against an electric shock, do not immerse the cord, plug, or appliance in water or any other liquid.
• WARNING: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
• Children of less than 3 years should be kept away unless continuously supervised.
• Do not use the appliance with a programmer, timer, separate remote-control system or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
• Do not use this heater in the immediate surroundings of a bath, a shower, or a swimming pool.
• Joists, beams, and rafters shall not be cut or notched to install the appliance.
• Please do not install the appliance close to curtains and other combustible materials. This could cause a fire.
• The appliance shall, under no circumstances, be covered with insulating material or similar material.
• The heater must be installed at least 1,8m above the floor.
• WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.
• Do not expose the battery to high temperatures or direct sunlight. Never throw batteries into the fire. There is a danger of an explosion!
• Keep batteries away from children. Batteries are not a toy!
• Do not open the batteries by force.
• Avoid contact with metallic objects.(Rings, nails, screws et cetera) there is a danger of short-circuiting!
• As a result of a short-circuit batteries may heat up considerably or even catch fire. this may result in burns.
• For your safety, the battery poles should be covered with adhesive strips during transport.
• Do not touch a ruptured and/or leaking battery. If the liquid from the battery gets into your eyes, rinse your eyes as soon as possible with clean water, without rubbing your eyes. Immediately go to the hospital. If it is not treated properly, it can cause eye problems.
• WARNING: In order to avoid overheating, do not cover the heater.

PARTS DESCRIPTION

1. Heater unit
2.  Display
3.  Remote control

BEFORE THE FIRST USE

• Use plugs and screws to install the appliance.
• Do not install the appliance near curtains or any other material that is easily inflammable.
• Drill two holes in the wall 2 meters above the floor.
• Make sure the distance between the holes is 315 mm.
• The distance between the product and the ceiling(and the side) should be ≥ 30cm.
• Keep the tips of the screws out of the wall for 10 mm.
• Fix the appliance to the wall by using the screws.
• When the product is installed, The screw is aligned with the hole “A” on the product. After hanging, the product must be moved to the “B”, in order to firmly fix.
• See the installation picture.
• Plug the power plug into the wall socket.
• Note: maximum weight is 4.1kg, the wall should be able to carry this weight.

Present time setting:

• At the first time the heater will start up or after the power has been cut off the present time has to be set.
• Set day of the week, led display 01 is Monday, 02 is Tuesday .. 07 is Sunday. Press + or – button to select the present day and confirm by pushing the OK button.
• Set hours, led display 0H, press + or – to adjust the hour from 0H to 23H, press OK button to confirm.
•  Set minutes, led display 00, press + or – to adjust the minutes from 0min to 59min, press OK button to confirm.
• If OK button is not pressed within 10 seconds after the adjustment, the setting will be canceled.

USE

• Turn on the heater by pressing the on/off button.
• The normal way to operate the machine is by using the remote control.
• If you cannot find or use the remote control, there is a possibility to switch on the heater manually by pressing the small start/stop switch under the on/off switch. This will only start the heater in high heat with oscillation mode, press again to stop the heater.
• The fan continues to operate for 30 seconds when the heater is switched off.

Display symbol description

1.  24/7: Week timer
2.  FAN: Fan in use
3.  LOW: Low heat
4.  HIGH: High heat
5.  °C: Led display temperature
6.  Swing: Oscillation mode on/off
7.  Temp: Light on: set temperature mode; Light flickering: open window detection on
8.  Timer: Timer mode on

Remote control

1. Power button :
   • Press this button to turn the heater on or off (it will take up to 30 seconds  before the fan completely turns off after shutdown)
2.  Heating:
   • Use this button to choose between low heat or high heat.
3.  Open window detection
   • Open window protection cannot start when the heater is in fan mode.
   • Press the open window detection button to start or stop the open window detection mode.
   • Temperature detection will start after 1 minute.
   • For 10 minutes in a cycle the temperature will be detected every 5 minutes.
   • If the temperature is <8°C than the detection start check point temperature the appliance will start heating.
   • If the temperature is >8°C than the detection start check point temperature the appliance will stop heating and go into the standby mode.
   •  When the 10 minute cycle is finished, the appliance stops heating, alarm sounds 5 times, the fan operates for 30 seconds and then the heater will go into standby.
   • Press the window detection button again to begin the next cycle.
4.  Timer
   • Press the timer button several times to set the timer as follows. 1 hour, 2 hour, 3 hour… 8 hour.
   • The timer function can’t be used when the week timer is active.
5. Set temperature
   •  Press this button to set the temperature, Press the + or the – button to adjust the temperature, the temperature range is 18-45°C.
   • If the set temperature is equal to or lower than environment temperature, the heating will stop.
   • If the set temperature is 1-2°C higher than the environment temperature the appliance will start low heating.
   • If the set temperature is higher or equal to +3°C than the environment temperature the appliance will start high heating.
   • Press the OK button to complete the set temperature mode.
6.  OK
   • Use this button to confirm actions.
7. Week timer
   • Press week timer button to activate this function.
   • Led will display P1, push the button again will take you to the P2 setting, again P3 and so on until P6. Pushing the week timer 7 times will cancel this function.
   • When the desired P mode is in display push the OK button to confirm.
   • See below table for information about the different P mode settings:
   • P6 free mode, push week timer button until it displays P6 than press OK, led display 1 as in Monday, push + or – to select the desired day (1-7,set from Monday to Sunday) and push OK to confirm the correct day.
   •  Led display 00, push + or – to set the desired start hour (from 0H to 23H) then press OK to confirm.
   • Led display 00 again, push + or – to set the desired stop time and confirm with OK.
   • There only can be set one start and one stop time a day.
   • The mode only works in hours and not in minutes.
8. + button
   • Use this button to go one step further.
9.  Cancel
   • Use this button to cancel the temperature settings or the week timer mode.
10.  – button
    • Use this button to go one step back.
11.  Oscillation button
    •  Use the oscillation button to turn on the oscillation mode. The airflow will now move from side to side. Press the button again to turn it off.
    • To turn the unit off, press the on/off button again.
    • The fan keeps on working for about 30 seconds to cool down the heater inside (when having used heating).
    • Maximum temperature is 51°C, the device will shut down automatically if a temperature of 51°C is detected.
    • The heater is protected against overheating. This will switch off the heater automatically in case of overheating due to total or partial obstruction of the grids. In this case, unplug the appliance and wait for about 30 minutes to cool down. After that remove the object that is obstructing the grids.

CLEANING AND MAINTENANCE

• Always unplug the device and let it cool down completely before cleaning
• Clean the outside with a damp cloth. Never use harsh and abrasive cleaners, steel wool or a scouring pad as this will damage the device. Do not immerse in water or other liquid.
• Clean de air inlet and outlet regularly with a vacuum cleaner to remove dust.

ENVIRONMENT
This appliance should not be put into the domestic garbage at the end of its durability but must be offered at a central point for the recycling of electric and electronic domestic appliances. This symbol on the appliance, instruction manual, and packaging puts your attention to this important issue. The materials used in this appliance can be recycled. By recycling used domestic appliances, you contribute an important push to the protection of our environment. Ask your local authorities for information regarding the point of recollection. The European directive for batteries (2006/66/EC) states that it is not permitted to throw batteries away with household waste. They may contain substances that are harmful to the environment. Empty batteries can be handed over to a local, public collection point or a local recycling center. To avoid overheating as a result of a short circuit, lithium batteries must be removed from the product and the poles must be protected using insulation tape or some other means against short-circuiting. You can find all available information and spare parts at www.tristar.eu!

Tristar Europe B.V. | Jules Verneweg 87 5015 BH Tilburg | The Netherlands

Documents / Resources

| TRISTAR KA-5075 2000 Watt Electric Heater [pdf] Instruction Manual
KA-5075, 2000 Watt Electric Heater, KA-5075 2000 Watt Electric Heater, Electric Heater, Heater
---|---

References

• Tristar | Household appliances - Unbeatable basics for your home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>