AUSSIE TRAVELLER JVC KD-X341 Single DIN DVD Audio Head Unit User Manual

: June 1, 2024
: AUSSIE TRAVELLER

Table of Contents

AUSSIE TRAVELLER JVC KD-X341 Single DIN DVD Audio Head Unit
Product Information
Product Usage Instructions
FAQs
PRODUCT INTRODUCTION
OPERATION
TECHNICAL PARAMETERS
INSTALLATION
TROUBLESHOOTING
WARRANTY STATEMENT
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AUSSIE TRAVELLER JVC KD-X341 Single DIN DVD Audio Head Unit

Product Information

Specifications:
- Type: Single DIN DVD Audio Head Unit
- Power: DC 12V
- Display: LCD Screen
- Media Compatibility: DVD, USB, SD/TF, Bluetooth, Aux
- Equalizer Modes: Rock, Pop, Classic, Flat, EQ Off

Product Usage Instructions

Basic Operations:
- Inserting and Ejecting Disk: Press the designated button to insert and eject the disk.
- Power On/Off: Press the PWR button to power on the unit. Press again to power off.
- Clock Setting: Press CLK to show the present time. Hold to adjust the hour and minute using the volume knob.
- Equalizer Settings: Press EQ to select from various equalizer modes like Rock, Pop, Classic, Flat, or EQ Off.
- Mode Selection: Use the MODE button to switch between different modes like Radio, Disc, USB, SD/TF, Bluetooth, Aux 1, and Aux 2.

FAQs

Q: How do I save radio stations on preset buttons?
- A: To save a radio station on a preset button, tune to the desired station then press and hold the corresponding preset button until the station is saved.
Q: How do I skip songs in music mode?
- A: In music mode, use the designated buttons to skip to the previous or next song. You can also hold these buttons for additional functions like rewind or fast-forward.

Read this installation instruction thoroughly. Incorrect installation or operation may void any warranty. Incorrect use or operation may cause serious injury.

PRODUCT INTRODUCTION

Add music to the entertainment list on your next trip away with the Aussie Traveller Single DIN DVD Head Unit.
Featuring a LCD screen, Bluetooth, AUX and USB connectivity as well as AM/FM radio, it is easy to start the music playing in your campsite.
Single DIN is the standard size for car/RV stereos. Standard DIN slots measure 180×50mm (2-1/8 inch×7-1/8 inch.)

$AUSSIE-TRAVELLER-JVC-KD-X341-Single-DIN-DVD-Audio-Head-Unit-FIG-1 $1$$

OPERATION

BASIC OPERATIONS:
- Press to insert and eject the disk.
- PWR (POWER)
- Press to power on the unit.
- Press again to power off.
- CLK (CLOCK)
- Press to show the present time.
- Hold to adjust the hour, rotate the volume knob to adjust. Press to adjust the minute, and rotate the volume
- knob to adjust. Press CLK again to confirm the setting.
- EQ (EQUALISER)
- Press to select from ROCK > POP > CLASS > FLAT > EQ OFF.
- MODE
- Press to change the mode: RADIO > DISC > USB > SD/TF > BT > AUX 1 > AUX 2 (if all functions are available).
- BND (BAND)
- In radio mode:
  - Press to change between FM1 > FM2 > FM3 > AM1 > AM2.
  - Hold to scan stations and store the stations into No. buttons automatically. Press again to stop the scan and store process.
- In music mode:
  - Press to display the music information.
  - Hold for song selection function: rotate the VOL. knob to select songs, press VOL. knob to display.
- VOLUME / SELECT KNOB
- Turn the volume knob clockwise to turn up the volume, turn the volume knob counter-clockwise to turn down the volume.
- Repeatedly press to select VOL > Bass (+/-7) > Treble (+/-7) > Balance (L/R 7) > Fader (R/F 7) > LOUD >
- EQ > DX (LOC) > STEREO (MONO) > VOL, rotate the volume knob to adjust the setting. The DX (LOC), and STEREO (MONO) are adjusted under radio mode.
- EQ: when the LCD EQ, selected the EQ as following: Rock > Pop > Class > Flat > Off by rotating the volume knob.
- LOUD: when the LCD LOUD, turning on/off LOUD by rotating the volume knob. Hold the Vol. Knob for setting the time at 12/24 displaying.
- In radio mode:
- - Press to automatically search the radio stations backwards.
  - Hold to switch from AUTO to MANUAL search backward.
  - Press to manually search stations backward.
- In music mode:
  - Press to skip to the previous song.
  - Hold to rewind.
- In radio mode:
- Press to automatically search the radio stations forwards.
- Hold to switch from AUTO to MANUAL search forward.
- Press to manually search stations forwards.
- In music mode:
  - Press to skip to the next song.
  - Hold to fast-forward.
- - In radio mode:
  - Press to display the stored station, hold to save the present station to this button.
- In music mode:
  - Press to pause and press again to resume playing music.
  - Hold to switch the Audio/Video/Image file displaying at USB & Mini SD mode.
- 2 / INT
- In radio mode:
  - Press to display the stored station, hold to save the present station to this button.
- In music mode:
  - Press to display songs on an LCD screen, each song displays for 10 seconds. Press again to select the displayed song.
- 3 / RPT (REPEAT)
- In radio mode:
  - Press to display the stored station, press to save the present station to this button.
- In music mode:
  - Press to repeat the song. Press again to release from repeat function.
- 4 / RDM (RANDOM)
- In radio mode:
  - Press to display the stored station, press to save the present station to this button.
- In music mode:
  - Press to have the songs play at random. Press again to stop randomization.
- 5 / -10
- In radio mode:
  - Press to display the stored station, press to save the present station to this button.
- In music mode:
  - Press to skip backward, 10 songs at a time. Hold to read last folder from mp3 folders.
- 6 / +10
- In radio mode:
  - Short press to display the stored station, long press to save the present station to this button.
- In music mode:
  - Press to skip forwards, 10 songs at a time. Hold to read the next folder from mp3 folders.
- MICRO SD CARD
- Insert the Micro SD card, the system will display accordingly.
- Insert the USB, the system will display accordingly.
- AUX IN
- Outer signal input socket.
RADIO OPERATION:
- PRESET STATIONS
- You can choose to save radio stations as presets. Each band allows for 6 stations — FM1, FM2, FM3, AM1, and AM2.
- Repeatedly press the BND button, you will see the following:
- Hold the button or button, to scan the stations manually;
- Press the or button, to scan the stations automatically. After you scan the station, long press your desired number button (No. 1–6) to store the station to the chosen number button.
- NOTE: If you stored another station in the same number button, the station you stored before will be overwritten.
- PLAY PRESET STATIONS
- Repeatedly press the BND button to choose the band as you want.
- Press the No. button 1–6 to play the stations you stored.
- NOTE: If you cannot play the preset stations, you can repeatedly hold the button or button, it will scan the stations automatically.
MP3 PLAY OPERATION:
- The system will start to play any time when you insert the USB/Micro SD card. When it displays the USB, the icon of USB blinks. When it displays the micro SD card, the icon of SD blinks.
- Press the button or button to play the next/last song; hold to fast-forward/rewind.
- Press the 1 button to pause, press it again to resume.
- Press the 2 button to display the songs on the LCD screen, the unit will display the songs for 10 seconds.
- Press the 3 button to turn on or release the repeat function.
- Press the 4 button to turn on or release a random function.
- Press to skip backward, 10 songs at a time. Hold to read the last folder from mp3 folders.
- Press to skip forwards, 10 songs at a time. Hold to read the next folder from mp3 folders.
DVD OPERATION:
- NOTE: DVD and CD compatible.
- The system will start to play any time when you insert the DVD. Insert DVD with label facing up.
- Press the button or button to play the next/last chapter; hold to fast-forward/rewind.
- Press the 1 button to pause, press it again to resume.
- Press the 2 button – no action in DVD mode.
- Press the 3 button to choose RPT CHP (Chapter)/TIT (Title)/ALL.
- Press the 4 button to turn RDM ON/OFF.
- Press to skip backward, 10 videos at a time. Hold to read last folder from mp3 folders.
- Press to skip forwards, 10 videos at a time. Hold to read the next folder from mp3 folders.
CLOCK OPERATION:
- Press to show the present time.
- Hold to enter into hour adjustment, rotate the volume knob to adjust.
- Press again to adjust minute, and rotate the volume knob to adjust.
BLUETOOTH OPERATION:
- Before you can use a Bluetooth device, it must be paired and connected.
- Make sure Bluetooth is activated on your device before you begin the pairing process.
- Repeatedly press the Mode button until you see BT.
- On your connecting device, open the Bluetooth setting and search for ATRV BT+ and select it.
- On your device, allow to pair with ATRV BT+ (no code needed).
- When paired, PHONE appears on the head unit screen.
- You can select the music from your device to display, and BTAUDIO appears on the unit screen.

TECHNICAL PARAMETERS

TUNER SECTION

CAUTION When replacing a fuse, please select the fuse of the same specification, do not replace it with others.

INSTALLATION

INSTALLATION DIAGRAM:
- Before installing the main unit, please place the main unit at a desired position, and connect the speaker wire and power wire for test use.
- After testing the main unit and confirming it is in working condition, fix the main unit.
INSTALL THE MAIN UNIT:
- Install the support cradle in the panel, and bend the clamp of the support.
- Connect the power wire and speaker wire, fix the fixing piece to the RV.
- Insert the antenna plug, push the main unit into the support cradle.
DISASSEMBLE THE MAIN UNIT:
- Insert two disassembly keys into the left and right gap, make sure the keys hook the main unit, pull to remove the main unit from the cradle, then disassemble the connection wire and unplug the antenna plug.
WIRING DIAGRAM $AUSSIE-TRAVELLER-JVC-KD-X341-Single-DIN-DVD-Audio-Head-Unit-FIG-1 $10$$
FADER FUNCTION:
- Fader allows you to control the sound either inside or outside the van. When installing the head unit, ensure you wire the correct speakers front and rear, to control inside and outside.
- Eg: All wired ‘rear’ speakers will be outside, all speakers wired to ‘front’ will be inside.

TROUBLESHOOTING

FAULT	REASON	SOLUTION
LCD doesn’t display	Yellow wire is not connected with battery + (positive)

Ensure the yellow wire is connected with battery + (positive)
The fuse of red wire is open| Replace fuse
The panel connector is dirty| Clean the panel
No sound| No power supply| Connect the power wire
The speaker wire is open circuit| Connect speaker wire
SD card doesn’t have a song with the corresponding format| Check the contents of the SD card
Low sound (not clear)| Power internal resistance is high| Replace power supply
The antenna is not connected correctly| Check the antenna plug
Mono track| One channel of the speaker wire is an open circuit| Check the speaker wire
The amplifier integrated circuit is damaged| Replace the IC of the amplifier
System down| Power supplier not stable| Long press the reset button

NOTE: Technical data is subject to change without prior notice.

WARRANTY STATEMENT

Aussie Traveller Pty Ltd ACN 642 775 460 (Aussie Traveller) offers the following warranty about the products it supplies directly or through an authorized manufacturer, dealer or approved service repair agent (Product).

Australian Consumer Law
The benefits of this warranty are in addition to any rights and remedies imposed by Australian State and Federal legislation that cannot be excluded. Nothing in this warranty is to be interpreted as excluding, restricting or modifying any State or Federal legislation applicable to the supply of goods and services which cannot be excluded, restricted or modified. If you are a consumer as defined in the Australian Consumer Law: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Warranty

Aussie Traveller warrants that subject to the exclusions and limitations below, all parts of the manufacture and assembly of the Product will be free from defects in materials and workmanship (Warranty) for 12 months from the date of purchase as follows:

This Warranty is activated at the time of purchase by the final retail customer (being the owner of the Product).
In the event the Product is purchased by a manufacturer, dealer or approved service repair agent, this Warranty will commence at the time the final retail customer makes payment for the Product to the wholesale purchaser.
If the Product is purchased directly from Aussie Traveller for use by final retail customer and not to be on sold in any way, the Warranty will commence at the time of the original purchase.

Warranty Period
This Warranty cannot be assigned or transferred to a subsequent owner of the Product. The purchaser or final retail customer should inspect the Product immediately when received or at vehicle handover, to ensure that it appears free from any damage or defect, and matches the description provided. If after accepting the Product, a defect appears in the manufacture or assembly of the Product before the end of the Warranty Period and Aussie Traveller finds the Product to be defective in materials or workmanship, Aussie Traveller will, in its sole discretion, either:

a. replace, repair or refund the Product or the defective part of the Product free of charge; or
b. cause the Product or the defective part of the Product to be replaced or repaired by a qualified repairer free of charge.

In arranging Warranty inspection, service, and repair, Aussie Traveller will seek to provide the details of an approved service agent within your geographic area. Should one not be available, or if the Product is in use in travel, Aussie Traveller reserves the right to seek to arrange a repair or replacement at the next available location on the route of travel. Aussie Traveller reserves the right to replace defective parts of the Product with parts and components of similar quality, grade and composition where an identical part or component is not available. Products presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the Product.

Aussie Traveller Awning Products
This Warranty covers specified defects in materials or workmanship for Awning Products as follows:

The vinyl fabric is warranted against:
- a. holes caused by mildew (mildew will form on dust and dirt and stain fabric if fabric is not kept clean).
- b. excessive cracking, peeling, hardening, or loss of strength while used under normal conditions.
- c. excessive fading (a slight color change may occur due to ultraviolet rays).
All hardware components including the roller are warranted not to bend or break under normal use (excluding high winds, water pooling, and accidents).

Making a Warranty Claim

If a defect covered by this Warranty appears, the Customer must first contact Aussie Traveller within 7 days of first becoming aware of the defect. Aussie Traveller will assist the Customer to rectify and resolve any Product issue that may arise.
When claiming this Warranty, Aussie Traveller requires that the following information be provided before any further action will be taken.

Original Invoice (Document or Number);
Make and model of the Product;
Make and model of the vehicle (if Product fitted);
Vehicle build date (if Product fitted);
Vehicle chassis number;
Description of damage and/or repair required;
Photos of the damage and/or repair; and
Appropriate documentation (such as historical and maintenance records).

Aussie Traveller reserves the right to request more information or images should what is provided not be sufficient to assess the Warranty claim. The Product must be made available to Aussie Traveller or its authorized repair agent for inspection and testing. If such inspection and testing find no defect in the Product, the final retail customer must pay Aussie Traveller’s usual costs of service work and testing. The final retail customer must bear the cost of the transport of the Product to and from Aussie Traveller or the authorized repair agent, and all insurance of the Product.

Exclusions
This Warranty will not apply where:

the Product has been repaired, altered, or modified by someone other than Aussie Traveller, or without the written consent of Aussie Traveller or an authorized repair agent;
the alleged defect in the Product is within acceptable industry tolerances and variances;
Aussie Traveller cannot establish any fault in the Product after testing and inspection;
the Product has been used other than for the purpose for which it was designed;
the alleged defect in the Product has arisen due to the final retail customer’s failure to properly use and
maintain the Product by any of Aussie Traveller’s instructions, recommendations, and specifications (including applicable maintenance schedules);
the alleged defect in the Product has arisen due to the final retail customer’s request to customize the Product;
the Product has been subject to abnormal conditions, including environment, temperature, high or excessive wind, water, fire, humidity, pressure, stress or similar;
the alleged defect has arisen due to abuse, misuse, neglect, or accident;
unauthorized parts or accessories have been used on or about the Product;
the Product has been overloaded or involved in an accident;
the alleged damage or defect has been caused by normal wear and tear;
the alleged damage to fabric has been caused by storm, wind or rain, or stretching of fabric caused by water pooling on fabric;
breakage or bending of hardware components has been caused by storm, wind rain, or water pooling on fabric.

Replacement Warranty Item

If, under Warranty, a Product is replaced or repaired by Aussie Traveller or an Aussie Traveller agent, unless provided in writing to indicate otherwise, the replacement Product will carry the remaining Warranty terms and conditions, including length of time, of the original purchased Product.

Change of Mind

Aussie Traveller understands that at times, final retail customers may change their mind. Choose carefully as return and credit requests for items purchased by mistake or “change of mind” reasons may not be approved.
Aussie Traveller will not accept Product returns under these circumstances unless by written approval by an authorized Aussie Traveller representative. If approved, an administration and restocking fee may apply.

Limitations

Aussie Traveller makes no express warranties or representations other than those set out in this Warranty.
The repair or replacement of the Product or part of the Product is the absolute limit of Aussie Traveller’s liability under this express Warranty.