GRUNDFOS SP3A-6 Electric Deep Well Pump Instruction Manual
- June 9, 2024
- GRUNDFOS
Table of Contents
SP3A-6 Electric Deep Well Pump Instruction Manual
Product No.: 10001K06
SP3A-6 Electric Deep Well Pump
Submersible borehole pump, suitable for pumping clean water. Can be installed
vertically or horizontally. All steel components are made in stainless steel,
EN 1.4301 (AISI 304), that ensures high corrosive resistance. This pump
carries drinking water approval.
The pump is fitted with a 0.37 kW MS402 motor with sand shield, lip seal,
water-lubricated journal bearings and a volume compensating diaphragm. The
motor is a canned type submersible motor offering good mechanical stability
and high efficiency. Suitable for temperatures up to 40 °C.
The motor is not fitted with a temperature sensor. If temp erature monitoring
is desired, a Pt1000 sensor can be fitted.
The motor is for direct-on-line starting (DOL).
Further product details
The pump is suitable for applications similar to the following:
– raw-water supply
– irrigation
– groundwater lowering
– pressure boosting
– fountain applications.
Pump
All pump surfaces that are in contact with pumped liquids are made in stainless steel which makes them corrosionand wear-resistant. The corrosion diagram below shows the capabilities of the pump and motor in relation to the temperature in Celsius (y-axis) and the concentration of chloride in ppm (x-axis).
The elastomer parts in the pump are made of NBR (Nitrile-Butadiene Rubber) and
TPU (Thermoplastic Poly-Urethane) which offers good wear resistance and long
service intervals.
The suction interconnector is fitted with a strainer to prevent large
particles from entering the pump. The suction interconnector is designed to
comply with NEMA standards for motor mounting/dimensions.
Motor
The stator is hermetically encapsulated in stainless steel and the windings
are embedded in polymer compound. This results in high mechanical stability,
optimum cooling and reduces the risk of short circuits in the windings.
The shaft seal is of the lip seal type characterised by low friction against
the rotor shaft. The NBR elastomer offers good wear resistance, good
elasticity and resistance to particles. The rubber material is approved for
use in potable water.
The motor can be fitted with a Pt100 or Pt1000 sensor that together with a
control unit ensures that the maximum operating temperature conditions are not
exceeded.
Liquid:|
---|---
Pumped liquid:| Water
Liquid max temp:| 40 °C
Max liquid t at 0.15 m/sec:| 40 °C
Selected liquid temperature:| 20 °C
Density:| 998.2 kg/m³
Technical:|
Pump speed on which pump data are based:| 2900 rpm
Rated flow:| 3 m³/h
Rated head:| 27 m
Shaft seal for motor:| LIPSEAL
Approvals on nameplate:| CE,EAC
Curve tolerance:| ISO9906:2012 3B
Motor version:| T40
Specification for shaft end:| SPLINE
Materials:|
Pump:| Stainless steel
EN 1.4301
AISI 304
Impeller:| Stainless steel
EN 1.4301
AISI 304
Motor:| Stainless steel
DIN W.-Nr. 1.4301
AISI 304
Installation:|
Pump outlet:| Rp1 1/4
Motor diameter:| 4 inch
Electrical data:|
Motor type:| MS402
Rated power – P2:| 0.37 kW
Power (P2) required by pump:| 0.37 kW
Mains frequency:| 50 Hz
Rated voltage:| 3 x 380-400-415 V
Rated current:| 1.30-1.40-1.50 A
Starting current:| 400-390-380 %
Cos phi – power factor:| 0.70-0.64-0.60
Rated speed:| 2850-2860-2870 rpm
Start. method:| direct-on-line
Enclosure class (IEC 34-5):| IP68
Insulation class (IEC 85):| B
Built-in temp. transmitter:| no
Motor No:| 79192002
Windings:| Enamelled
Others:|
Minimum efficiency index, MEI ≥:| 0.7
ErP status:| EuP Standalone/Prod.
Net weight:| 10.2 kg
Gross weight:| 11.4 kg
Shipping volume:| 0.011 m³
Danish VVS No.:| 388313060
Swedish RSK No.:| 5852977
Finnish LVI No.:| 4762650
Country of origin:| DK
Custom tariff no.:| 84137029
Description| Value
---|---
General information:|
Product name:| SP 3A-6
Product No:| 10001K06
EAN number:| 5.7086E+12
Technical:|
Pump speed on which pump data are based:| 2900 rpm
Rated flow:| 3 m³/h
Rated head:| 27 m
Stages:| 6
Impeller reduc.:| NONE
Shaft seal for motor:| LIPSEAL
Approvals on nameplate:| CE,EAC
Curve tolerance:| ISO9906:2012 3B
Model:| A
Valve:| YES
Motor version:| T40
Specification for shaft end:| SPLINE
Materials:|
Pump:| Stainless steel
Pump:| EN 1.4301
Pump:| AISI 304
Impeller:| Stainless steel
Impeller:| EN 1.4301
Impeller:| AISI 304
Motor:| Stainless steel
Motor:| DIN W.-Nr. 1.4301
Motor:| AISI 304
Installation:|
Pump outlet:| Rp1 1/4
Motor diameter:| 4 inch
Liquid:|
Pumped liquid:| Water
Liquid max temp:| 40 °C
Max liquid t at 0.15 m/sec:| 40 °C
Selected liquid temperature:| 20 °C
Density:| 998.2 kg/m³
Electrical data:|
Motor type:| MS402
Applic. motor:| GRUNDFOS
Rated power – P2:| 0.37 kW
Power (P2) required by pump:| 0.37 kW
Mains frequency:| 50 Hz
Rated voltage:| 3 x 380-400-415 V
Rated current:| 1.30-1.40-1.50 A
Starting current:| 400-390-380 %
Cos phi – power factor:| 0.70-0.64-0.60
Rated speed:| 2850-2860-2870 rpm
Start. method:| direct-on-line
Enclosure class (IEC 34-5):| IP68
Insulation class (IEC 85):| B
Built-in motor protection:| NONE
Thermal protec:| external
Built-in temp. transmitter:| no
Motor No:| 79192002
Windings:| Enamelled
Others:|
Minimum efficiency index, MEI ≥:| 0.7
ErP status:| EuP Standalone/Prod.
Net weight:| 10.2 kg
Gross weight:| 11.4 kg
Shipping volume:| 0.011 m³
Danish VVS No.:| 388313060
Swedish RSK No.:| 5852977
Finnish LVI No.:| 4762650
Country of origin:| DK
Custom tariff no.:| 84137029
Printed from Grundfos Product Centre [2022.20.005]
Documents / Resources
|
GRUNDFOS SP3A-6 Electric Deep Well
Pump
[pdf] Instruction Manual
SP3A-6 Electric Deep Well Pump, SP3A-6, Electric Deep Well Pump, Deep Well
Pump, Well Pump, Pump
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>