LANCOM ISG-1000 GmbH System User Guide
- September 4, 2022
- LANCOM
Table of Contents
LANCOM ISG-1000
Quick Reference Guide Cloud-ready
ISG-1000 GmbH System
-
USB interface
You can use the USB interface to connect a USB printer or a USB storage device.
-
Serial configuration interface
Use the included serial configuration cable to connect the serial interface (COM) to the serial interface of the device you want to use for configuring / monitoring.
-
SFP / TP Ethernet interfaces (combo ports)
Insert suitable SFP modules into the SFP ports. Choose cables compatible with the SFP modules and connect them as described in the module’s documentation. SFP modules and cables are not included.
-
If desired, alternatively connect the ETH 1 – ETH 4 TP Ethernet interfaces to your PC or a LAN switch using one of the enclosed cables with the kiwi-colored connectors.
-
TP Ethernet interface
Use one of the enclosed cables with the kiwi-colored connectors to connect the interface ETH 5 to your PC or a LAN switch.
-
Reset button
Pressed up to 5 seconds: device restart Pressed until first flashing up of all LEDs: configuration reset and device restart -
The power connector and grounding point (device back side)
Supply power to the device via the power connector. Please7788 use the IEC power cable supplied (separately available for WW devices).
-
ATTENTION: High touch current possible! Connect to earth before connecting the power supply. For this purpose, remove the existing blind screw and use the enclosed grounding screw instead.
Please observe the following when setting up the device
- The mains plug of the device must be freely accessible.
- For devices to be operated on the desktop, please attach the adhesive rubber footpads.
- Do not rest any objects on top of the device and do not stack multiple devices.
- Keep the ventilation slots on the side of the device clear of obstruction.
- Mount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets.
Before initial startup, please make sure to take notice of the information
regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a
nearby power socket that is freely accessible at all times.
a POWER
Off| Device switched off
Green, permanentlythe | Deviceoperational, resp. device paired / claimed and
LANCOM Management Cloud (LMC) accessible
Green / red, blinking| No password set. Without a password, the configuration
data in the device is unprotected.
Red, blinking| Charge or time limit reached
1x green inverse blinking| Connection to the LMC active, pairing OK, device
not claimed
2x green inverse blinking| Pairing error, resp. LMC activation code not
available
3x green inverse blinking| LMC not accessible, resp. communication error
b TEMP|
---|---
Green, permanently| CPU temperature OK
Red, blinking| Hardware failure of the fan or CPU temperature too high;
additional acoustic signal
LCD display (rotating in two lines)
- Device name
- Firmware version
- Device temperature
- Date and time
- CPU load
- Memory usage
- Number of VPN tunnels)
- Data transfer in the reception direction
- Data transfer in the transmission direction
d ETH 1 – ETH 4 – TP (one green and orange LED each)
Both LEDs off| No networking device attached
Green, permanently| Connection to network device operational, no data traffic
Green, flickering| Data transmission
Orange off| 1000 Mbps
Orange, permanently| 10 / 100 Mbps
e ETH 1 – ETH 4 –| SFP (one green and orange LED each)
---|---
Both LEDs off| No networking device attached
Green, permanently| Connection to network device operational,
no data traffic
Green, flickering| Data transmission
Orange off| 1000 Mbps
Orange, permanently| 10 / 100 Mbps
ETH 5
Both LEDs off| No networking device attached
Green, permanently| Connection to network device operational, no data traffic
Green, flickering| Data transmission
Orange off| 1000 Mbps
Orange, permanently| 10 / 100 Mbps
The additional power LED statuses are displayed in a 5-second rotation if the device is configured to be managed by the LANCOM Management Cloud.