EDIFIER TWS1 Truly Wireless Stereo Earbuds User Manual
- June 9, 2024
- Edifier
Table of Contents
TWS1
Truly Wireless Stereo Earbuds
Product Description and Accessories
There are different size of earmuffs attached in the package, please select the suitable ones to wear.
Operational Guide
● Charge the Headphones
During using, if only red light flashes, it indicates headphones are at low
battery level, please use them after fully charged.
Charging: place the headphones into the charging case
Red light lit in a breathing pattern = charging
Red light off = fully charged
Charging time: about 1.5 hours for a full charging
● Charge the Charging Case
If indicator light flashes slowly, its flashing times mean the times that the
headphones can be charged, if the indicator light flashes rapidly, it means
the charging case has a low battery capacity, please charge it in time; once
the battery runs out, the headphones cannot be turned on.
Indicator light steady lit = charging Indicator light off = fully charged
Warning: The rechargeable batteries that provide power for this product
must be disposed properly for recycling. Do not dispose of batteries in fire
to prevent an explosion.
If not used for long periods of time, it is recommended to charge the product
with lithium battery at least once per 3 months.
● Power ON/OFF
- Power on automatically when taken out from the charging case;
- Power off automatically while placed into the charging case.
● Bluetooth Connection
-
Two Headphones Mode
• Open the charging case to take two headphones out, press and hold the touch button of the left headphone to enter pairing state, red and blue light flashing rapidly;
• Set mobile phone to search for and connect to “EDIFIER TWS1”, after pairing is successful, blue light will flash slowly. -
One Headphone Mode
If use one headphone only, please take the left or right headphone out from the charging case, and refer to the procedures mentioned in “Two Headphones Mode” to pair it with mobile phone.
● TWS (true wireless stereo) Pairing of the Left and Right Headphones
The left and right headphones have finished TWS pairing before leaving the
factory. If the wireless connection fails to resume, please follow the steps
below to re-pair:
- With no TWS and Bluetooth connection, double press the touch buttons to enter TWS pairing state, blue lights flashing rapidly;
- After pairing is done, blue lights of two headphones will flash slowly.
Functional Operation Instructions
● Music playback (same operation for the left and right headphones)
● Call (same operation for the left and right headphones)
- Clear pairing records: With no TWS and Bluetooth connection, respectively press and hold the touch button for 8 seconds.
- Disconnect from mobile phone: When the phone is connected, no music is playing and no phone conversation, press and hold the touch button for 5 seconds.
FAQs
Red light instead of blue light flashes.****
• The headphones are at low battery level, please recharge the headphones.
Red light is off during charging.****
• Please ensure the headphones are correctly placed into the charging case.
• When the headphones are not used for long periods of time, the battery will
enter sleep state, it needs to charge about 30 minutes and then the red light
will be lit.
No sound****
• Check if the headphones are operating.
• Check if the headphones volume is at an appropriate level.
• Check if the headphones are correctly connected with mobile phone.
• Check if the headphones are operating within a normal working range.
The call quality of the headphones is not good.****
• Check if mobile phone is in an area with strong signal.
• Please ensure the headphones are within effective distance (10m) and
no obstacle between the headphones and mobile phone.
When playing music, cannot control pause/play/previous track/next track via headphones.****
• Please ensure the paired device support AVRCP (Audio/Video Remote Control Profile) profile.
Maintenance
During using, please read the following suggestions carefully.
- Keep the product away from humid places to avoid affecting internal circuit. Do not use the product during intense exercise or with much sweat to prevent sweat from dropping into the product to make damage.
- Do not put the product in places exposed to sun or with high temperature. High temperature will shorten service life of electronic components, damage battery and deform plastic components.
- Do not put the product in cold places to avoid damaging internal circuit board.
- Do not dismantle the product. Non-professional personnel may damage the product.
- Do not drop, strongly vibrate, strike the product with hard object to avoid damaging internal circuit.
- Do not use drastic chemicals or cleaner to clean the product.
- Do not use sharp objects to scratch product surface to avoid damaging shell and affecting looking.
If the product cannot operate properly, please send it to your qualified maintenance agency.
EDIFIER International Limited
www.edifier.com
2019 Edifier International Limited. All rights reserved.
Printed in China
NOTICE:
For the need of technical improvement and system upgrade, information
contained herein may be subject to change from time to time without prior
notice.
Products of EDIFIER will be customized for different applications.
Pictures and illustrations shown on this manual may be slightly different from
actual product.
Picture for reference only, actual product prevails.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>