fein ASBS18-10AS 18V Li-Ion Coolpack Cordless Vacuum Cleaner Instruction Manual

fein ASBS18-10AS 18V Li-Ion Coolpack Cordless Vacuum Cleaner

Safety information for vacuum cleaners

Read all the safety information and instructions. Failure to observe the safety information and follow instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.

•  This vacuum cleaner is not intended for use by children or persons with physical, sensory or mental impairments. It should not be used by persons who have insufficient experience and knowledge. Otherwise, there is a risk of operating errors and injuries.
•  Supervise children. This will ensure that children do not play with the vacuum cleaner.
• Do not vacuum beech or oak wood dust or asbestos. Only vacuum rock dust in conjunction with dust extraction systems, which have been explicitly approved for use with ASBS18‑10AS by FEIN. These substances are classified as carcinogenic.

WARNING: Only use the vacuum cleaner if you have been adequately informed about the use of the equipment, the substances to be vacuumed and how to dispose of these safely. Thorough instruction on how to use the equipment prevents accidental misuse and injuries.

• The vacuum cleaner is suitable for vacuuming dry substances, and can also be used to vacuum liquids when taking appropriate measures. The penetration of liquids increases the risk of an electric shock.
• Do not use the vacuum cleaner to vacuum combustible or explosive liquids, such as petrol, oil, alcohol or solvents. Do not vacuum hot, burning or explosive dust. Do not operate the vacuum cleaner in areas subject to explosion hazards. Dust, vapours and liquids can ignite or explode.

WARNING: If you notice a foam or water leak, switch off the vacuum cleaner immediately and empty the container. Otherwise, the vacuum cleaner can become damaged.
NOTE: The vacuum cleaner must only be stored indoors.

•  Clean the float regularly and check whether it is damaged. Otherwise, the equipment may not function properly.
•  Ensure that the workplace is well ventilated.
• The vacuum cleaner should be repaired exclusively by a qualified professional using only genuine spare parts. This will ensure that the safety of the vacuum cleaner is
  maintained.

WARNING: The dust extractor contains dust particles that pose a risk to health. Emptying and maintenance procedures, including the disposal of dust containers, should only be carried out by professionals. Suitable protective equipment is required. Do not operate the vacuum cleaner unless the complete filter system is correctly inserted. Otherwise, you are putting your health at risk.

• Before using the equipment for the first time, check that the vacuum hose is in perfect condition. Leave the vacuum hose fitted to the vacuum cleaner while doing this so that no dust escapes accidentally. Otherwise, you may end up inhaling dust particles.

• Do not clean the vacuum cleaner by spraying a jet of water directly at it. Water entering the top of the vacuum cleaner will increase the risk of electric shock.

• Do not open the battery. There is a risk of short-circuiting.

•  In case of damage and improper use of the battery, vapours may be emitted. The battery can set alight or explode. Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapours may irritate the respiratory system.

•  If used incorrectly or if the battery is damaged, flammable liquid may be ejected from the battery. Contact with this liquid should be avoided. If contact accidentally occurs, rinse off with water. If the liquid comes into contact with your eyes, seek additional medical attention. Liquid ejected from the battery may cause irritation or burns.

•  The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat.

•  When the battery is not in use, keep it away from paper clips, coins, keys, nails, screws or other small metal objects that could make a connection from one terminal to another. A short circuit between the battery terminals may cause burns or a fire.

•  Only use the AMP Share battery in the manufacturer’s products or those of the AMPShare partners. This is the only way in which you can protect the battery against
  dangerous overload.

•  Only charge the batteries using chargers recommended by the manufacturer. A charger that is suitable for one type of battery may pose a fire risk when used with a different battery.

• Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water and moisture. There is a risk of explosion and short-circuiting.

• Do not screw or nail any signs or labels onto the dust extractor. Damaged insulation offers no protection against electric shocks. Use stick-on labels instead.

Symbols

The following symbols may provide you with important information pertaining to the use of your dust extractor. Please take note of these symbols and their meaning. Knowing what these symbols mean will help you to use your extractor more effectively and more safely.

Symbols and their meaning WARNING: Read all the safety and general instructions. Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury.
WARNING: The dust extractor contains dust particles that pose a risk to health. Emptying and maintenance procedures, including the disposal of dust containers, should only be carried out by professionals. Suitable protective equipment is required. Do not operate the dust extractor unless the complete filter system is correctly inserted. Otherwise, you are putting your health at risk.

Symbols and their meaning
Dust extractor from dust class L in accordance with IEC/EN 60335-2-69 for the dry extraction of harmful dusts with an exposure limit of > 1 mg/m³

Product Description and Specifications

Please observe the illustrations at the beginning of this operating manual.

Intended Use

The dust extractor is intended for collecting, vacuuming, conveying and separating non-flammable dry dusts, non-flammable liquids and a water-air mixture. The dust extraction capability of the dust extractor has been tested and corresponds to dust class L. It is suitable for the increased demands in professional use, e.g. in trade, industry and workshops. Dust extractors from dust class L in accordance with IEC/EN 60335‑2‑69 may only be used to vacuum and extract harmful dust with an exposure limit of > 1 mg/m³. Only use the dust extractor if you can fully evaluate all functions and carry them out without restrictions, or if you have received corresponding instructions.
The bagless filter system removes the need to use dust bags. Dirt is collected on the inside wall of the container.

Product Features

The numbering of the product features refers to the representation of the vacuum cleaner on the graphic pages.

1.  Container
2.  Catch for top part of dust extractor
3.  On/off button
4. Battery charge indicator
5. Top part of dust extractor
6.  Carrying handle
7. Adapter for vacuum hose/floor nozzle bracket
8. Hose adapter
9. Adapter for suction tube/crevice nozzle bracket
10. Battery compartment cover release button
11.  Battery compartment cover
12. Vacuum hose
13.  Dust extraction adapter
14. Curved nozzle
15.  Crevice nozzle
16. Floor nozzle
17.  Suction tube
18.  Battery bay
19. Rechargeable batterya)
20.  Rechargeable battery release buttona)
21. Bracket for suction tube and crevice nozzle
22.  Fixing bolt for bracket (23)
23.  Bracket for vacuum hose and floor nozzle
24. Snap fastener
25.  Castor
26. Castor adapter
27.  False air intake
28.  Filter
29. Float
30.  Filter holder
31.  Retaining strap of the vacuum hose

• Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.

Technical data

to +50
Recommended rechargeable batteries (2–8 Ah)| | GBA 18V… ProCORE18V…
Recommended chargers| | GAL 18…
Operating time per battery charge| min/Ah| 4

•  Measured at 20–25 °C with rechargeable battery GBA 18V 8.0Ah.
•  measured with vacuum hose (12) and curved nozzle (14)
•  Depends on battery in use
•  Limited performance at temperatures < 0 °C

Noise/Vibration Information

Noise emission values determined according to EN 60335‑2‑69. Typically the A-weighted sound pressure level of the dust extractor is 79 dB(A). Uncertainty K = 2 dB. The noise level when working can exceed the volume stated. Wear hearing protection! Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 60335‑2‑69: ah < 2.5 m/s2, K = 1.5 m/s2.

Assembly

Remove the battery before cleaning or performing maintenance on the dust extractor, making tool adjustments, changing accessories or placing the dust extractor in storage. This safety measure prevents the dust extractor from being started accidentally.

Charging the Battery

Use only the chargers listed in the technical data. Only these chargers are matched to the lithiumion battery of your dust extractor.
Note: Lithiumion rechargeable batteries are supplied partially charged according to international transport regulations. To ensure full rechargeable battery capacity, fully charge the rechargeable battery before using your tool for the first time.

• Do not continue to press the on/off button after the dust extractor has automatically switched itself off. This can damage the battery.

A significantly reduced operating time after charging indicates that the battery has deteriorated and must be replaced. Follow the instructions on correct disposal.

Battery Charge Indicator
When the rechargeable battery is inserted, you can see the state of charge of the battery on the battery charge indicator (4) on the dust extractor. When the rechargeable battery is removed, you can see this on the battery itself.

Battery Charge Indicator on the Dust Extractor
After the dust extractor is switched on, the five green LEDs of the battery charge indicator (4) will light up individually one after another in ascending and descending order. Then the LEDs will indicate the state of charge of the battery (19).

Battery Charge Indicator on the Rechargeable Battery
If the rechargeable battery is removed from dust extractor, its state of charge may be indicated by the green LEDs of the battery charge indicator on the battery. Press the button for the battery charge indicator or to show the state of charge. If no LED lights up after pressing the button for the battery charge indicator, then the battery is defective and must be replaced.

Battery model GBA 18V…

Battery model ProCORE18V…

Inserting and Removing the Battery

•  Do not use force to insert the battery. The battery is designed in such a way that it can only be inserted into the product when it is in the right position.
• Keep the battery compartment and the battery bay clean and dry at all times to ensure good, safe operation.
  •  Press the release button (10) to open the battery compartment cover (11).
  •  Slide the battery (19) into the battery bay (18) until it audibly clicks into place.
  • To remove the battery (19), press the release button (20) on the battery and pull it out of the battery bay (18).
  • Close the battery compartment cover (11).

Fitting the Brackets for Extractor Accessories

•  Slide the bracket (21) for the suction tube and crevice nozzle firmly into the adapter (9) provided for it from above until it clicks into place.
• Slide the bracket (23) for the vacuum hose and floor nozzle firmly into the adapter (7) provided for it from above and tighten the fixing bolts (22).

Fitting the vacuum hose

•  Insert the vacuum hose (12) into the hose adapter (8) until both snap fasteners (24) of the vacuum hose click into place.

Note: The friction generated by the dust in the vacuum hose and accessory during extraction causes an electrostatic charge that the user may experience as static discharge (depending on environmental factors and their physiological state).

Fitting the Vacuuming Accessories
The vacuum hose (12) is equipped with a clip system which can be used to connect vacuuming accessories (dust extraction adapter (13), curved nozzle (14)).

Fitting the extraction adapter or curved nozzle

•  Fit the extraction adapter (13) or the curved nozzle (14) to the vacuum hose (12) until the two snap fasteners (24) on the vacuum hose audibly click into place.
• To remove the adapter, press the snap fasteners (24) inwards and pull apart the components.

Fitting the Nozzles and Tubes

•  If required, place the suction tubes (17) firmly inside one another and then attach them firmly to the curved nozzle (14).
•  Attach the floor nozzle (16) or the crevice nozzle (15) firmly to the suction tube (17) or the curved nozzle (14).

Fitting the Rollers Insert the 4 fastening pins on the rollers (25) into the roller adapters (26) until they audibly click into place. Other rollers can also be used as per the EN 12529 standard (11 mm fastening pin diameter).

• Check the functionality of the roller brakes before using the dust extractor.

Operation

•  Remove the battery before cleaning or performing maintenance on the dust extractor, making tool adjustments, changing accessories or placing the dust extractor in storage. This safety measure prevents the dust extractor from being started accidentally.
•  Ensure that the work area is clean and tidy to minimise the risk of tripping.

Starting Operation

• The dust extractor must not be used without a filter.
•  Do not use damaged filters (e.g. no cracks, small holes, etc.). Replace any damaged filters immediately.
•  Before extraction, ensure that the filter unit is securely fitted.
•  Before extraction, ensure that the battery compartment cover is securely closed.
•  Please inform yourself about the applicable regulations/laws on how to handle harmful types of dust in your country.

The dust extractor must categorically not be used in potentially explosive areas. To ensure optimum suction power, you must always fully unwind the vacuum hose (12) from the vacuum hose bracket (23).

Switching On and Off
To switch on the dust extractor, briefly press the on/off button (3). To switch off the dust extractor, press the on/off button (3) again. For safety reasons, the dust extractor does not switch on if the on/off button (3) is held down for longer than five seconds.

Dry Vacuuming
Extracting dust that accumulates from working power tools

•  There must be a sufficient air exchange rate (L) in the room when the exhaust air comes back into the room. Be aware of the corresponding national regulations.
  •  Fit the dust extraction adapter (13) or the curved nozzle (14) (see “Fitting the extraction adapter or curved nozzle (see figure D)”, page 19).
  •  Insert the extraction adapter (13) or the curved nozzle (14) into the power tool’s dust extraction outlet.

Only when using the dust extraction adapter (13):
Note: When working with power tools that have a low air feed into the vacuum hose (e.g. jigsaws, sanders, etc.), the false air intake (27) of the dust extraction adapter (13) must be opened. This will improve the total output of the dust extractor and the power tool. To do this, turn the ring above the false air intake (27) until the opening is at its maximum size.

Wet Vacuuming

• Do not use the vacuum cleaner to vacuum combustible or explosive liquids, such as petrol, oil, alcohol or solvents. Do not vacuum hot, burning or explosive dust. Do not operate the vacuum cleaner in areas subject to explosion hazards. Dust, vapours and liquids can ignite or explode.

Before wet vacuuming:

• Empty the container (1).
•  Clean the filter (28) and fit it back into the dust extractor (see “Cleaning/replacing filters.
  

The dust extractor is equipped with a float (29). Extraction is stopped when the maximum filling level is reached.

After wet vacuuming, always:

•  Empty the container (1).
•  Empty the water from the filter (28).

To prevent mould growth after wet vacuuming:

•  Remove the dust extractor lid (5) and leave it to dry thoroughly.
• Remove the filter (28) and also leave this to dry thoroughly (see “Cleaning/replacing filters (see figures H1–H2)”, page 20).

Maintenance and Service

•  Remove the battery before cleaning or performing maintenance on the dust extractor, making tool adjustments, changing accessories or placing the dust extractor in storage. This safety measure prevents the dust extractor from being started accidentally.
• To ensure safe and efficient operation, always keep the dust extractor and the ventilation slots clean.

For the user to carry out maintenance, the dust extractor needs to be disassembled, cleaned and maintained as far as this is possible without endangering maintenance personnel or other persons. Before disassembly, the dust extractor should be cleaned to prevent any potential hazards. The room/enclosure in which the dust extractor is disassembled should be well ventilated. Wear personal protective equipment while carrying out maintenance. After completing maintenance, the maintenance area should be cleaned. An inspection regarding the dust extraction capability must be carried out at least once a year by the manufacturer or someone who has been trained, e.g. to check for filter damage, that the dust extractor is tight and that the control unit is functioning correctly. Class L dust extractors which were located in dirty environments should have their exteriors, as well as all their components, cleaned or treated with sealant. When performing maintenance and repair work, all dirty parts that cannot be cleaned satisfactorily must be disposed of. Such parts must be disposed of in impermeable bags in accordance with the valid provisions for disposing of such waste.

• Clean the housing of the dust extractor occasionally with a damp cloth.
•  Clean dirty charging pins using a dry cloth.

Cleaning the container
Clean the container (1) after each use in order to ensure that the dust extractor continues to perform optimally.

•  Open the catches (2) and remove the dust extractor lid (5).
•  Shake out the container (1) over a suitable waste bin.
•  If necessary, clean the container with a damp cloth. Clean the filter if required (see “Cleaning/replacing filters (see figures H1–H2)”, page 20).
•  Replace the dust extractor lid (5) and close the catches (2).

Cleaning/replacing filters

Suction power is dependent on the condition of the filter. Therefore, the filter should be cleaned regularly. Replace any damaged filters immediately.

• Open the catches (2) and remove the dust extractor lid (5).

• Turn the filter (28) as far as it will go in the direction of rotation and remove it from the filter bracket (30).

• If the filter is dry:
  Tap the filter (28) on the side of a suitable waste bin. When doing so, ensure that you do not damage the flaps on the filter. To achieve maximum suction power, brush down the flaps of the filter using a soft brush. or
  If the filter is wet:
  Rinse the filter (28) under running water and then leave it to dry thoroughly.
  or
  Replace the filter (28) if it is damaged.

•  Position the filter (28) over the filter bracket (30) and turn it as far as it will go in the direction of rotation  .

•  Replace the dust extractor lid (5) and close the catches (2).

Make sure that the catches engage firmly.

Faults

If the suction power is insufficient, check:

•  Is the container (1) full?

  • (see “Cleaning the container .
    

•  Is the filter (28) clogged with dust?

  •  (see “Cleaning/replacing filters (see figures H1–H2)”, page 20).

• Is the battery capacity too weak?

  •  (see “Charging the battery”, page 18).

Regularly emptying the container (1) and cleaning the filter (28) will ensure optimum suction power. If suction power is not achieved after that, the dust extractor should be sent to the after-sales service.

Storage

•  Insert the suction tubes (17) into the brackets (21).
•  Insert the crevice nozzle (15) into a suction tube (17).
• Insert the floor nozzle (16) into the bracket (23).
• Wind the vacuum hose (12) around the bracket (23) from below and fasten the retaining strap (31).
• Only ever carry the dust extractor by the carrying handle (6) or by the carrying strap (if present).
• Store the dust extractor in a dry room and secure it so that it cannot be used by unauthorized persons.

Range of accessories

Only use original FEIN accessories. The accessories must be intended for the power tool type.

Maintenance and After-Sales Service

Please note that power tools must only be repaired, serviced and tested by qualified electricians. Improper repairs can pose considerable hazards to the user. When working metals in extreme conditions, conductive dust can settle in the interior of the power tool. Regularly blow out the interior of the power tool through the ventilation openings with dry and oil-free compressed air. When processing gypsum-containing materials, dust can settle in the interior of the power tool and on the switching element and may harden due to the humidity. This may impair the switching mechanism. Regularly blow out the interior of the power tool through the ventilation openings and switching element with dry and oil-free compressed air. Products that have come into contact with asbestos must not be brought for repair. Dispose of products contaminated with asbestos according to the regulations for disposing of waste containing asbestos that apply in the country of use. If FEIN power tools or accessories require repair, please contact the FEIN after-sales service. The address can be found online at www.fein.com.
Replace labels and warnings on the power tool if they show signs of ageing or wear. The current spare parts list for this power tool can be found online at www.fein.com.
Only use original spare parts.

Warranty and Guarantee

The warranty on the product is in accordance with the statutory provisions of the country in which it is placed on the market.Furthermore, the FEIN guarantee applies in accordance with the FEIN manufacturer guarantee declaration. It is possible that only some of the accessories described or depicted in this operating manual will be supplied with the power tool you have purchased.

Declaration of Conformity

The CE declaration only applies to countries of the European Union and EFTA (European Free Trade Association) and only to products intended for the EU or EFTA market. Once the product is placed on the EU market, the UKCA mark will cease to be valid. The UKCA declaration only applies to the British market (England, Wales and Scotland) and only to products intended for the British market. Once the product is placed on the British market, the CE mark will cease to be valid. FEIN declares, under its sole responsibility, that this product complies with the relevant provisions specified on the final pages of this instruction manual.
Technical documentation at:
C. & E. Fein GmbH, 73529 Schwäbisch Gmünd, Germany

Transport

The recommended lithiumion batteries are subject to legislation on the transport of dangerous goods. The user can transport the batteries by road without further requirements. When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labelling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required. Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.

Disposal

Vacuum cleaners, batteries, accessories and packaging should be sorted for environmentally friendly recycling.

• Do not dispose of vacuum cleaners or battery packs/batteries with house-hold waste.

Only for EU countries: English
According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, dust extractors that are no longer usable, and, according to the Directive 2006/66/EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner. If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for United Kingdom:
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

Battery packs/batteries:
Li-ion:
Please observe the notes in the section on transport (see “Transport”, page 21).

EU Declaration of Conformity
Cordless wet/  dry dust extractor
We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards.
Technical file at:
Article number
Cordless wet/dry dust extractor Article number
ASBS18‑10AS                            9 260 42 03 00 0
We declare under our sole responsibility that the stated products comply with all applicable provisi-ons of the directives and regulations listed below and are in conformity with the following standards.
Technical file at:

The Supply of Machinery (Safety) Regulations 2008
The Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
EN 60335-1:2012+A11:2014+A13:2017+
A14:2019+A1:2019+A2:2019+A15:2021
EN 60335-2-69:2012
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
i.V. S. Böhm
Director of Quality Management
*C. & E. Fein GmbH, 73529 Schwäbisch Gmünd
i.V. Dr. M. Hergesell
Director of Product Development
C. & E. Fein GmbH, Hans-Fein-Straße 81, 73529 Schwäbisch Gmünd-Bargau, Germany Schwäbisch Gmünd-Bargau, 24.06.2022
C. & E. Fein GmbH
Hans-Fein-Straße 81
73529 Schwäbisch Gmünd-Bargau
Germany
www.fein.com

References

• High quality power tools and accessories | C. & E. Fein GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>