veho ZB-7 Wireless Headphone User Manual
- June 9, 2024
- veho
Table of Contents
veho ZB-7 Wireless Headphone
Guide to the headphones
- Power button
- Power status LED
- Microphone
- 2.5mm audio port
- Active noise canceling
- Active noise-canceling LED
- Volume + / Next track
- Volume – / Previous track
- USB-C charging port
- Charging status LED
Charging
Charging the headphones Connect the supplied USB-C cable to the headphones and
then into a compatible 5V⎓1A power source. The status LED will show solid red
when charging, turning blue when fully charged. When the battery is low, a
warning tone will sound every 3 minutes.
Pairing
Pairing with a device Ensure the headphones are off. Press and hold the power button for 5 seconds, and wait until a ‘Pairing’ tone sounds and the power status LED flashes red/blue. Select ‘Veho ZB-7’ from the Bluetooth® menu on your device.
Line-in cable
Using the Line-in cable Connect the supplied 2.5mm audio cable from the
headphone audio port to your device. The headphones will default to line-in
mode whilst the audio cable is connected.
Functions
- Power on/off Press and hold the power button for 3 seconds to turn it on, and the power status LED will flash blue. Press and hold the power button for another 3 seconds to turn it off, and the power status LED will flash red.
- Play/pause Press the power button once to play and once again to pause.
- Volume up/Next track Press the (+) button for 2 seconds to skip to the next track. Press once to increase the volume.
- Volume down/Previous track Press and hold the (-) button for 2 seconds to skip to the previous track. Press once to reduce the volume.
- Voice assistant Simultaneously press and hold the volume + and volume – buttons for 2 seconds.
- Active Noise Cancelling (ANC) Press the ANC button once to change modes between on/off/ambient mode. Active Noise Cancellation uses the microphone and speakers to reduce background and surrounding noises.
- Bass control Press and hold the ANC button for 2 seconds to change modes between bass up/normal.
- Multipoint connection Pair the headphones to a Bluetooth® device, disable Bluetooth® on this device, and repeat pairing instructions with a second device. The multipoint connection allows the headphones to maintain simultaneous connections with two source devices.
- Reset Ensure the headphones are disconnected from the devices. Simultaneously press and hold the power and volume – buttons for 5 seconds.
- Answering/ending calls Press the power button once to answer an incoming call. Press once again to end the call.
- Rejecting calls Press and hold the power button for 2 seconds to reject an incoming call.
- Call mute/unmute Press and hold the volume + button for 3 seconds.
- Call switch Simultaneously press and hold the volume + and volume – buttons for 2 seconds during a call to switch between the headphones and mobile device.
- Number redial Double-click the power button to redial the most recent contact on your call log.
Specifications
- Bluetooth® version V5.0
- Driver size 40mm
- Speaker sensitivity 117 ±3dB
- Impedance 32Ω
- Frequency response 20Hz–20KHz
- ANC reduction 32 dB
- Input voltage 5V⎓1A
- Battery size 500mAh
- Charge time Approx. 72 minutes
- Playtime Up to 32 hours
- Charging port type USB-C
- Wireless range of Up to 10 meters
- Dimensions 164.2mm x 190.6mm x 89.1mm
- Weight 230g
FCC STATEMENT
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
EC DECLARATION OF CONFORMITY
Hereby, Veho UK LTD declares that the radio equipment type (VEP-024-ZB7-B) is
in compliance with Directive 2014/53/EU. The full text of the EU Declaration
of Conformity is available at https://veho-world.com/compliance/.
- Frequency band(s) – 20Hz-20KHz
- Maximum radio-frequency power – ≤10dBm
Support
Should you need to contact Veho for support or troubleshooting for your ZB-7 Headphones, please contact us via our chat box on our website at: www.veho- world.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>