OSRAM OT Wi 35-220-240-400 D NFC CA L Optotronic LED Power Supply Instruction Manual

: June 9, 2024
: OSRAM

Table of Contents

OSRAM OT Wi 35-220-240-400 D NFC CA L Optotronic LED Power Supply
INSTALLATION
Emergency Lighting
APP
DESCRIPTION
OSRAM GmbH
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OSRAM OT Wi 35-220-240-400 D NFC CA L Optotronic LED Power Supply

INSTALLATION

Installing and operating information (non-isolated driver): Connect only LED load type. LED module will be switched off when output voltage drops below 54V or rises above 240V. Wiring information (see fig. A): The light fixture maker is the final responsible for the proper PE connection. Do not connect the outputs of two or more units. Output current adjustment = via programming software using Near Field Communication (NFC) in mains off mode only. For Near Field Communication (NFC) please refer to Tuner4TRONIC at www.osram.com/ds. Unit is permanently damaged if mains is applied to the terminals 21/23. Lines 21/23 max. 2 m whole length excl. modules. There are two places in the app where you can unpair a Casambi- enabled device from a network.

Go to the ‘Luminaires’ tab and tap ‘edit’. Unpair a luminaire by tapping the (“X”) that will appear in the corner of the relevant luminaire icon. You can also double-tap a luminaire icon to open the “luminaire properties” screen, and then scroll down and tap ‘Unpair device’.
Go to the “Nearby devices” screen found under the ‘More’ tab. Tap on the device you wish to unpair and select ‘Unpair device’. This will unpair the luminaire if you have modification (administrator) rights to the network.

If you don’t have the modification rights to the network that the device is paired to then you need to have access to the devices power switch to be able to unpair. Tap on the device you wish to unpair and select ‘Unpair device’ and the app will open the ‘Unpair’ screen. Tap on the ‘Start’ button and an orange “Time bar” will appear and start to move across the screen. During the time it takes the bar to move across the screen, flick the power switch off and back on again. This should unpair the device. If unpairing succeeds then there is a message that luminaire has been unpaired. If it does not succeed then try again but switch the power off and on again more slowly (This may be needed for devices that use an additional power supply; such as a CBU-PWM4). If unpairing continues to be unsuccessful then it is probably the case that the power switch is not correct for the device you are trying to unpair.

Emergency Lighting

This LED power supply complies with EN 61347-2-13 Annex J and is suitable for emergency lighting fixtures according to EN 60598-2-22 except those used in high-risk task areas. Hereby, OSRAM GmbH declares that the radio equipment types OT Wi 35 D NFC CA L, OT Wi 75 D NFC CA L and OT Wi 100 D NFC CA L are in compliance with Directive 2014/53/EU and the relevant statutory instruments . The full text of the EU declaration of conformity or the UK declaration of conformity is available at the following internet address: www.osram.com/ot-indoor- ce.

APP

Download Casambi app from App store or Google play. For the correct functioning of the Casambi app refer to the Casambi website: http://www.casambi.com. The Casambi App is provided to you by Casambi. OSRAM shall have no liability for the Casambi app and does not make any representations, express or implied, about the availability and/or performance of the Casambi app. The Casambi cloud services are provided to you by Casambi. OSRAM shall have no liability for the Casambi cloud services and does not make any representations, express or implied, about the availability and/or performance of the Casambi cloud services. OSRAM shall have no liability for and does not make any representations, express or implied, about the connectivity of Casambi-ready products of OSRAM with any other Casambi-ready products.
www.casambi.com

NFC Frequency range: 13 553 – 13 567 kHz;
RF frequency range: 2402 – 2480 MHz;
Max HF output power (EIRP) of the product: 8 dBm.
Technical support: www.osram.com, +49 (0)89-6213-6000

DESCRIPTION

Casambi linear LED driver for luminaire integration.
Constant current LED Power Supply.
tc point.
Connect PE to case or PIN 3. Wire Preparation. Push in.
Designed and engineered in Germany/Italy. Made in Bulgaria.
picture only for reference, valid print on product.
Mains.
Input.
Output.
Year.
Week.
Mounting hint for proper radio connectivity. By integrating the device into a casing the wireless range could be affected, in particular by metal surfaces. Therefore, the wireless range needs to be verified after integration.
Do not place any mains voltage or LED supply wires within or close to this area.
Recommended minimal distance to metal parts.
Placement of integrated radio transmitter antenna.
Radiofrequency.
Wireless protocol.
Wireless range.
10 m line of sight