OVICX Q2S Plus Foldable Treadmill User Manual
- June 6, 2024
- OVICX
Table of Contents
USER MANUAL
About After-sales Service
We would love to hear from you, if you have any questions. do not hesitate to
contact us Emaitsupport@qiaosports.com
Product Brief Introduction
Product Name: Treadmill Product Model: OVICX-02S PLUS
Safety Instruction
Thank you for choosing our product. The correct use of a treadmill is the guarantee for your safety and convenience. Please read the following contents carefully before you use the treadmill.
- Please make sure you have installed the treadmill correctly before powering it on. For easy plugging in, be careful not to cover the socket on the wall.
- Please plug the power cord into the socket connected to the ground for safety. The plug of the treadmill is unique, if the power cord got damaged, please contact our distributor or contact us directly.
- The treadmill is indoor equipment, please do not use it outdoor. The place where to position the treadmill should be clean and flat. Please keep it away from moisture. Please do not put the treadmill on anything such as a thick blanket which may influence the air circulation under the treadmill. The treadmill is special equipment, so please do not use it for any other purpose.
- Do not wear too large or too loose clothes when doing exercise, in order to prevent accidents from your clothes hung to any parts of the treadmill. We recommend you to wear sneakers or gym shoes with rubber bottoms.
- Please do not take off the protection cover casually. If you do need to open it for maintenance, please unplug the power cord first.
- If it is the first time for you to use the treadmill, please do remember to grab the handrails till you feel comfortable.
- If the treadmill accelerates suddenly or increases its speed automatically caused by the problem of the electronic console system, please pull out the safety key to stop the equipment instantly.
- Please unplug and lay the power cord away when not using the treadmill.
- To avoid any risk, you should not allow children close to the treadmill when it is on.
- There should be adults accompanying when children use the treadmill.
- Before exercise, please warm-up for 3-5 minutes, such as exercising joint and jogging.
- Turn on power at the bottom to start the treadmill. Press “on/off” button, and the digital display shows “Start” and then the treadmill begins to work. The system shall start at speed” 1″ automatically, so the beginner could take this speed to warm up.
- Grab the front ends of the handrails by two hands, step onto the treadmill and increase the speed to 0.9mph to 1.8mph slowly. Keep your body straight, relax as much as possible, and walk with the running belt.
- After getting familiar with the treadmill functions, you can preset the exercise time and adjust it according to your own cadence.
- 0n the digital display, you can choose to show the speed, time, and distance of your exercise. Also, it can show the calorie you consumed and your heart rate on the digital display. During running, your heartbeat rate could be measured by grabbing the chips on the two handrails.
- Warning! Equipped with a 27.56-inch red magnetic safety key (the red one). If you find the treadmills abnormal or feel risky, please pull out this magnetic safety key to stop the treadmill instantly in order to avoid accident occurrence.
- While exercising, please clip the safety key(red) thread on the suitable position of your clothes, in order to pull it out to stop the treadmill immediately and ensure safety when an accident occurs. When you do not use the treadmill, please well keep the safety key to avoid and the third party to use it uncontrolled.
- When finishing your exercise, please plug off and put away the power cord.
- Warning! Do not touch any spare parts when it’s working.
- A heart rate sensor is not medical equipment. A lot of causes may lead to inaccurate test results, so the test results are only for reference.
- Warning! If you feel any potential danger during the exercise, you should step the two side handrails to jump to the ground or jump to two side footboards urgently.
- *Warning!78.7439.37** inch safety spare area behind the treadmill is required so that you can have enough space to jump off the working treadmill when any danger occurs.
- During exercise, 78.74 (Length)39.37 (Width)88.58 (Height)inch free space is required for safe operation
- Warning! The treadmill is indoor equipment. Please do not use it outdoor. Exercising on the treadmill is an aerobic exercise to strengthen the functions of your heart and lung. Muscle exercise is auxiliary.
- Warning! Any adjustment devices that may interfere with the user’s motion should not deviate from the design.
Hints:
- Beginners should get familiar with the function buttons on the panel before using the treadmill.
- To prevent falling down, please stand on the plastic anti-skid plates on both sides first when starting the treadmill instead of standing on the running belt directly.
- Before running, Please put on your sportswear instead of jeans or leather shoes.
- Please do not play with other people while using the treadmill. It is strictly forbidden to jump off the treadmill during the running process.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Product Technology Parameter and Component List
Technology Parameter
Product Model | VIC-Q2S PLUS |
---|---|
Unfolded Size | 64.9625.5944.88 inch |
Speed | 8.7mph |
Rated Voltage | 110V— |
Rated Frequency | 50/60Hz |
Rated Power | 1.25HP |
Efficient Running Area | 16.93*49.21 inch |
Display | LED |
Gross Weight | 110.23Ibs |
Net Weight | 94.80Ibs |
Dimensions | 66.1429.3310.04 inch |
Category and Level | HB |
App Connectivity | **** |
Safety Protection | 1. Safety switch on the meter |
2. Overcurrent fuse on the treadmill’s internal control panel
We reserve the right to improve or change the pictures and technical parameters of this product without prior notice. Please understand. Component List
No. | Name | Qty | Remarks |
---|---|---|---|
1 | Entire machine (base, mainframe and electric console) | 1 pc | |
2 | Spare parts box | 1 box | Safety key 1 pc |
Hexagon wrench 1 pc Lubricating silicone oil
1 bottle user manual 1pc Power cord 1 pc phone paste holder 1pc
Installation Instruction
Simple installation in 4 steps
-
Open the package, take out the treadmill, spare parts box, power cord, instruction manual from the box.
-
Turn the knobs on both sides of the treadmill counterclockwise until they are completely released. Raise the uprights of both sides as shown in the figure. Then fasten the knobs on both sides clockwise until both uprights are fixed tightly.
-
Press the button with your left hand to unlock the handrail, and raise the handrail of the treadmill you’re your right hand until it is fully locked. Install the other side in the same way. ( Before using, please press the handrail by strength to make sure it is tightly fixed and would not fall down)
-
Take out the phone holder and insert it into the slot.
-
Check again the above installation is tightly fixed before use. Take out the red safety key from the spare parts bag and insert it into the key slot of control console, and then plug the power cord and turn on the power to start the treadmill.
Upright Description
Pull the supporting feet on both sides outward as shown in picture 1, then rotate them by 90 degrees in the direction shown, then release them into the slot (as shown in picture 2), then erect the treadmill as shown in picture
Button Instruction
Panel
(1). Operation Window Display
1. Speed Window It shows the current speed Unit: mph; Accuracy: 0.1mph
2. Distance, Calorie, and Heart-rate Window
2.1 When the distance indicator light is on, it displays the total distance
from the start of the workout. Unit: mile; Accuracy: 0.01 mile
2.2When the Calorie indicator light is on, it displays your total calorie
consumption from the start of the workout. Unit: kcal; Accuracy: 0.01 kcal
2.3 It shows your heart rate once it gets the data of your hand pulse
3. Time Window
3.1 It displays the running time. (Range: 0-99:59)
3.2 It displays the error code when a failure occurs
4. Indicator Light
4.1 Calorie Indicator Light: When the window displays calorie indicator light
will be on.
4.2 Distance Indicator Light: When the window displays distance indictor light
will be on
4.3 Bottom light: When the treadmill starts running, the bottom light
treadmill stops running, and the bottom light is off.
(2). Button and function:
- On/off: Press the button to start the treadmill
- Switch button: Press this button to switch distance, calorie data in the display window.
- Plus: Adjust the speed. With each press of the button, speed increases by 0.1
- Minus: Adjust the speed. With each press of the button, speed decreases by 0.1
- 5. Speed down: Press this button when feeling tired, then the treadmill will switch into the walking state( 2.4mph). And press this button again after a break, the running speed will automatically go back to the previous speed.
Error code display
A: Error information of control device and troubleshooting methods
Information Code | Possible reasons | Troubleshooting Guideline |
---|---|---|
Er 1 | Safety key disconnected | 1.1 Check whether the safety key is connected |
to the designated position.
1.2 Check whether the safety key is loosened or dropped
1.3 Check or replace the safety key
Er 3| Problem on the bottom chip near the motor| 2.1 Replace the chip
Er 7| Problem on the motor or Motor disconnected| 3.1 Check if the motor cable
is loosened or dropped.
3.2 Check or replace the motor.
3.3 Check or replace the chip
3.4 Check if the line of safety key is connecting well or not
Er 8| No signal error| 4.1 Check if the connecting cable is loosened, dropped
or damaged
4.2 Check or replace the console
4.3 Check if the light of the controller and the LED is on
4.4 Check or replace the chip
Er 9| Overload protection| 5.1 Check if overloaded
5.2 Check if the mechanical running parts are jammed
5.3Check if there is a lack of lubricant oil. When lack of lubricant oil, the
friction between plate and belt would increase
5.4 Check if the running plate is badly worn
5.5 Check if the running belt is badly worn 5.6 Check if the motor is short-
circuited 5.7 Check or replace the controller
Er 10| Overvoltage protection| 6.1 Please check if the voltage on the power
supply line is 20% greater than DC 110V-
6.2 Check or replace the chip
Er1 1| Over-current protection| 7.1 Check if overloaded
7.2 Check if the mechanical running parts are jammed
7.3 Check if there is a lack of lubricant oil. When lack of lubricant oil, the
friction between plate and belt would increase
7.4 Check if the running plate is badly worn
7.5 Check if the running belt is badly worn 7.6 Check if the motor is severely
short-circuited
7.7 Check or replace the controller
7.8 IGBT tube short-circuited
---|---|---
Er1 2| Electric motor short circuit| 8.1Check whether there is any foreign
matter at the output end of the controller causing a short circuit
8.2 Check or replace the controller
| Some or all of the buttons are not working well| 9.1 Check or replace the
buttons
9.2 Check or replace the console
9.3 Uncover the upper case of the electric meter and test if the buttons work
well
9.4 Disconnect power supply, re-plug, and then check if the buttons work well
Exercise Suggestion and Guideline
If it is your first time using a motorized running machine, you need to read the below tips:
Preparation
Before exercise, it is better to know your own health status in order to make
an exercise plan based on it. It is recommended to consult a doctor or a
professional to get multiplier effects. Before first use of the running
machine, please stand by it and learn how to control it, for example, start,
stop, adjust speed and etc. After getting familiar with it, you can start to
use the running machine. Stand on the plastic anti-slip plates on the two
sides of the track and seize the handrails with two hands. Then, turn on the
running machine and adjust the speed around 1.0-1.9mph (low speed). Keep your
body straight and your eyes look forward. Step on the running belt carefully
and relax until you can gradually follow the speed. When you are comfortable,
you may slowly increase the speed to 1.8-3.0mph. Keep this speed for about 10
minutes, and then slow down it until it stops. For your first time, please do
not run at high speed to prevent from falling down.
Exercise
Walk about 0.62mile at a fixed pace and record the time it spent.lt
maytakel5-25 minutes. When the speed is at 2.9mph, it shall take you about 12
minutes for a distance of 0.62mile. After you can easily do it a few times,
you can gradually increase the speed. Keep it for 30 minutes, and you can get
good exercise. Before you start to walk, please be patient and be aware that
this exercise is good for your health during your whole lifetime.
The Frequency of Exercise
Your target is to exercise 3-5 times every week, and each time exercise for
15-60 minutes. It is better to make an exercise schedule based on your body
status, rather than do it according to your own preferences. You can control
the intensity by adjusting the speed and exercise time.
Exercise Time
Shortcut: 15-20 minute exercise is a good way to save time. Warm up for 5
minutes at 2.4-2.9mph, and then increase speed by 0.2mph increment per minute
until you feel at a suitable speed, and keep running for about 45 minutes. You
will fully enjoy this exercise. The above content is for reference only.
Please consult professionals for more details.
Wearing
The only thing you need is just a pair of good shoes, and we recommend you to
wear running shoes or gym shoes during exercise. Meanwhile, please be careful
that there is nothing stuck on the shoes in order to avoid anything dropping
into the running machine and then damaging the running plate and belt. Clothes
should be comfortable and suitable for sports, and we recommend you to wear
breathable sportswear made from cotton.
Stretch exercise
No matter how fast you walk, it is better to do stretch exercises first. A
warm muscle is easier to stretch, so please spend 5-10 minutes to warm up
first. Then stop and use the below methods to do stretch exercises. Stretch
for 5 times and at least 10 seconds for each leg in the warm-up, and do it
again after exercise.
-
Stretch down
Keep your knees slightly curved, and slowly bend your body forward. Relax your back and shoulder and touch your toes with your hands (see figure 1). Keep this for 10-15 seconds, and then relax. Repeat it 3 times. -
Foot tendon stretch
Sit on a clean cushion, stretch one leg out and adduct another leg to cling the inner side of the leg stretched out, and then touch the toes by hand (see figure 2). Keep this gesture for 10-15 seconds and then relax. Repeat this 3 times for each leg. -
Foot and heel tendon stretch
Stand with your hands on the wall or tree and separate your two legs forward and back. Lean toward the wall or tree, and keep the back leg straight and put its heel to the floor (see figure 3). Keep this gesture for 10-15 seconds and then relax. Repeat this 3 times for each leg. -
Quadriceps stretch
Hold the wall or table by your left hand for balancing, extend your right hand back to grasp your right ankle, slowly pull the heel toward your butt until you feel the tightness of the front muscle on your thigh (see figure 4). Keep this gesture for 10-15 seconds and then relax. Repeat this 3 times for each leg. -
Sartorius muscle (inner muscle of thigh) stretch
Sit down with two soles facing each other and two knees outwards. Grasp the two feet and pull them towards your groin. Keep this gesture for 10-15 seconds, and then relax. Repeat this 3 times.
Exercise safety measures
Please consult a professional before exercise. He can give you some suggestions about exercise frequency, intensity and duration according to your age and physical condition. During exercise, if you feel chest choking or chest pain, irregular heartbeat, breathing difficulty, dizziness or any other discomfort, please stop immediately. And consult professionals before you resume the exercise. -14-
Maintenance Guideline and Instruction
1. Maintenance guideline
WARNING: Be sure that the electric running machine is not plugged in
before you clean or maintain the product. Cleaning: A comprehensive cleaning
shall significantly extend the product life. Remove dust regularly to keep
parts clean.lt is necessary to clean the exposed parts on two sides out of the
belt, and this shall decrease dust accumulation under the belt. Be sure your
sports shoes are clean before exercise and this could avoid lint from dropping
into the running machine and then damaging the running plate and belt. Scrub
the belt surface by a wet cloth with soap, and be careful not to spill water
on the electrical components or under the belt.
The running machine has been pre-coated with silicone oil between the running
plate and belt. It is necessary to lubricate it with silicone oil regularly
because the friction between the running belt and plate has big impact on
product life and performance. We recommend you to take regular inspection of
the running plate. If the running plate is damaged, please contact our
customer service center.
We recommend the user to inject the silicone oil between the running belt and
plate according to the following timetable: Low-frequency users (use time:
less than 3 hours per week): inject silicone oil once every 6 months Middle
frequency users (use time: 3-5 hours per week): inject silicone oil once every
3 months High-frequency users (use time: more than 5 hours per week): inject
silicone oil once every 1.5 months We recommend you to buy silicone oil from
your local distributor or contact us directly.
2. Maintenance instruction
In order to maintain your running machine better to extend product life, it
is recommended to turn off the running machine after using it for 2 hours and
have a 10 min break before continuing.
If the running belt is too loose, it could be slippery when you exercise; if
too tight, it may decrease the motor performance and increase the abrasion of
the drum and running belt. You can check whether the running belt is fitting
or not by raising the two sides of the running belt horizontally by hand. The
suitable distance between raised running belt and plate is 1.97-2.95inch.
2.1 Running plate lubrication
We mentioned above that it is necessary to inject silicone oil on the running
plate at the right time. But please do not use excessive silicone oil as the
lubricants are not the more the better. Remember: proper lubrication is an
important factor in extending the product life of a running machine.
The method to check whether it is necessary to inject silicone oil Raise the running belt and stretch your hand as far as possible to touch the central part of the backside of the running belt. If your hands can grab a little silicone oil (feel slightly moist), that means you do not need to inject silicone oil. If the running plate is dry and no silicone oil adheres to your hand, then you need to inject silicone oil. The procedure to inject silicone oil on the running plate:
Note: The cut is about 0.20 inch
a) As shown in the picture, cut the oil bottle mouth, twist off the long mouth
cover, tear the inner sealing paper, and then tighten the long mouth cover. In
order to make a good connection with the oil hole, do not cut too long when
cutting the mouth, about 0.20inch or less, as long as the oil can flow out.
b) Turn on the treadmill and run it at the lowest speed(0.6mph), then
lubricate the running belt as shown in picture c) Align the oil bottle with
the oil filler, squeeze the oil bottle slowly to let the oil flow into the
running belt through the oil pipe, and run the treadmill at a speed of 0.6mph
to evenly apply the silicone oil, and lightly tap on the belt in the middle.
In a few minutes, the silicone oil can be completely absorbed by the running
belt.
2.2 Tautness adjustment of the running belt.
The running belt has been adjusted to a suitable tautness twice after the
installation and before delivery. However, after use for a period of time, the
running belt could be somehow loose. For example, the user may feel a
standstill or slippery during his running. When this phenomenon occurs, please
adjust the tautness of the running belt by rotating both left and right
adjusting bolts clockwise with a half circle as a unit. (to tighten the
running belt, please operate in an anticlockwise direction). If the running
belt is too loose, the user will feel slippery when running; while it is also
not good if the running belt is too tight, because it shall increase the motor
load and damage the motor, running belt, roller and etc.
2.3 Running belt centering
Place the running machine on even ground. Start the running machine and set
the speed at about 2.1mph. If the running belt is tilted to the left side,
rotate the adjustment bolt on the left side by 1/2 circle in the clockwise
direction, and then rotate the adjustment bolt on the right side by 1/2 circle
in an anticlockwise direction. If the running belt is tilted to the right
side, rotate the adjustment bolt on the right side by 1/2 circle in the
clockwise direction, and then rotate the adjustment bolt on the left side by
1/2 circle in an anticlockwise direction.
If the running belt is tilted to the left side, rotate the adjusting bolt on
the left side clockwise or rotate the adjusting bolt on the right side
counterclockwise
If the running belt is tilted to the right side, rotate the adjusting bolt on
the right side clockwise or rotate the adjusting bolt on the left side
counterclockwise
2.4 Driving belt adjustment The driving belt has to be adjusted before
delivery. However, after using a period of time, the slipping phenomenon may
occur and the user can adjust the driving belt by himself. Adjustment
procedure (as shown in the right picture):
Rotate the adjustment bolt clockwise with a wrench
The adjustment range: take load without slipping as the standard Note: please
clean junk in the belt groove and pulley groove
OFFICE TECHNOLOGY CO.,LTD
www.goodsports.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>