ROC HOBBY 1:18 Mogrich RTR Green Instruction Manual

ROC HOBBY 1:18 Mogrich RTR Green

Introduction

This model is set up as a typical special transport form, which can be capable of transporting under complicated road conditions. The car is equipped with widened mirrors and waders, two orange warning lights on the roof, and a beautiful dashboard and cockpit interior visible through the windows. The hood can be opened for battery replacement, and it also serves as a storage space for the electronic board of the remote control system.
In addition, the rear cargo compartment can be opened on three sides for easy loading and unloading of cargo. The actual cargo floor and three sides of the door panels are made of wood,and a fine pattern is carefully curved in the model to simulate the texture of solid wood. The chassis is a typical four- link suspension with front and rear suspension travel to ensure the vehicle has excellent passability. The tires are newly made MPT (Multi-Purpose Tire) which has coarse and solid tread patterns suitable for extreme terrains such as mud and sand.
Two-channel digital proportional remote control system are integrated with light control, equipped with a power-packed electronic system: independent servo, two-in-one receiver, and ESC, 050 large-torque motors, 7.4V 380 mAh lithium battery to facilitate walking on any terrain. Endurance up to 30 minutes! Mogrich, an RC-powered model car that dominates all kinds of complex terrain.

Transmitter instruction

[1]| A/ B Mode switch key| [7]| Throttle trim + (TH TRIM +) mode A / light control switch 1 mode B
---|---|---|---
[2]| Re-set button（F.Reset）Mode A| [8]| Throttle trim – (TH TRIM – ) mode A / light control switch 2 mode B
[3]| Steering Trim+（ST TRIM+）Mode A| [9]| Channel 6 (reserved)
[4]| Steering Trim-（ST TRIM-） Mode A| [10]| Steering wheel
[5]| Power Switch| [11]| Throttle trigger
[6]| Reverse key mode a / steering angle limit mode B|  |
A/ B mode function toggle switch

F.Reset| In the use of the disorder settings, not back to the normal state, you can use Factory. Reset function|

Make sure that the mode function toggle switch is in mode A, hold the steering wheel left or right, and click the F. Reset button at the same time. After two clicks, it means that the factory settings have been completed.

REV| After replacing the steering gear, the steering gear is reversed| Make sure that the mode function toggle switch is in mode A, twist the left or right steering wheel, and click Rev button at the same time. After ringing, it means that the reverse setting of steering gear has been completed.
After replacing the motor, there is a reverse| Make sure that the mode function toggle switch is in mode A, pull or push the throttle, and click Rev button at the same time. After ringing, it means that the motor reverse setting has been completed.
Adjust 30 / 50 / 100% steering radian| Make sure that the mode function toggle switch is in mode B, and click the ST Angle key. After a click, it means that the 30% steering radian has been set. Click the ST Angle button again, and you will hear two beeps, indicating that the setting of 50% steering radian has been completed. Click the ST Angle button again, and you will hear three beeps, indicating that the 100% steering radian has been set. Then click to cycle to a click to indicate that the 30% steering radian has been set.
ST TRIM| When the steering center is not centered| Make sure that the mode function toggle switch is in mode A, press ST TRIM+ or – button to fine tune the steering center. Every click of the button will ring. When the maximum and minimum values are reached, a long sound will appear. When the median value is reached, it will ring twice.
TH TRIM| When the throttle is not centered| Make sure that the mode function toggle switch is in mode A, press TH TRIM + / – button to fine tune the throttle center. Every click of the button will ring. When reaching the maximum and minimum value, the button will ring, when reaching the median value, the button ring twice.
LED| Light setting| One – button for multi – mode switch
Emitter: forget reminder| If the transmitter does not receive any command, it will give an alarm after 10 minutes and enter sleep mode after 2 minutes
---|---
Transmitter: frequency alert| When the transmitter does not match the receiver, the indicator light of the transmitter keeps flashing
Transmitter: no frequency matching

+ low power reminder 4.5V

| The indicator light of the transmitter flashes slowly and makes a sound
Transmitter: low power reminder 4.5V| The indicator light of the transmitter flashes slowly
Car: frequency alert| The headlights keep flashing
Car: low power alarm 6.3 – 6.4v| All lights keep flashing, steering and throttle are not controlled
Car: reminders to prevent forgetting| If the vehicle does not receive any signal, it will flash back and forth

after 10 minutes and enter sleep mode after 2 minutes

Times for Pressing

Button| Light Position| Function| I| II| III| IV| V| Control Mod| Remarks|
LED+| Headlight| Always on| OFF| •| OFF| OFF| OFF|  |  |
Always Off| OFF| OFF| •| •| OFF|  |  |
Rear light|  |  |  |  |  |  | Throttle linkage control| The reversing lamp is on during reversing operation|

PARTS

VIBRATION AVOIDANCE GROUP

CAR HOPPER GROUP

FRAME GROUP A

FRAME GROUP B

HEAD GROUP

COMPLETE VEHICLE GROUP

TYRE GROUP

REAR AXLE GROUP

FRONT AXLE GROUP

Transmitter Battery Installation

Battery Type: AAA

Battery Installation:

1. Open the battery compartment cover.
2. Insert 4 fully-charged AAA batteries into the compartment. Make sure that the battery makes good contact with the battery compartment’s contacts.
3. Replace battery compartment cover.
   Low battery alarm: When the battery is lower than 4.2V, the LED on the panel will flash slowly.

Note: When installing the batteries, be careful to handle the positive and negative poles. (As shown in the picture on the right).

Warnings

• This vehicle is not intended for those under 14 years of age without proper adult supervision.
• It is not a toy! Failure to operate or maintain this vehicle in a safe manner can result in bodily harm.
• Replace damaged components with original factory parts. Pay special attention to the polarity of all vehicle wiring.
• Only use approved 2-cell lithium polymer batteries. Do not over-charge or over dis-charge, the battery as doing so may cause the battery to become a fire hazard. If the battery should become hot during charging, discontinue charging immediately and disconnect the battery from the charger.
• Never leave the battery unattended while charging. If you are unsure of how to charge this battery, please seek the advice of experienced RC users. Never let children charge the battery without adult supervision.
• The motor will become hot during use. Allow 10-15 minutes between runs for the vehicle to cool down. Doing so will prolong the life of your vehicle.
• Use common sense when selecting the environment to operate your vehicle. Do not operate near power cables, cellular/radio towers, deep water or unstable terrain. The operator is solely responsible for their actions.
• The product is composed of precision electrical components. It is critical to keep the product away from moisture and other contaminants. If exposed to a humid environment, make sure the electronics are fully dried prior to using them again.
• Always check the radio range of the vehicle prior to operation in order to prevent radio loss or interference.
• Operate this product with in your ability. If the vehicle is dangerous to retrieve, it’s never worth the risk.
• Always turn on the transmitter before connecting the battery on the model. When turning off the model, always disconnect the battery first, and then turn off the model, always disconnect the battery first, and then turn off the transmitter. If this order is reversed, the model may become uncontrollable and cause serious damage.
• Never allow transmitter batteries to run low as it may cause loss of vehicle control.
• Plastics on the vehicle are susceptible to damage or deformation due to extreme heat and cold climate. Do not store the model near any source of heat such as oven or heater. Store the model indoors, in a climate-controlled, room-temperature environment.
• Never shorten the receiver antenna; this may affect the transmitting range of the radio system.
• Only use specified battery (X4 AAA batteries).
• Do not open, disassemble, or attempt to repair the battery.
• Do not crush/puncture the battery, or short the external contacts.
• Do not expose to excessive heat or liquids.
• Do not drop the battery or expose to strong shocks or vibrations.
• Always store the battery in a cool, dry place.
• Do not use the battery if damaged.
• The Battey must be disconnected the receiver when charging.

INSTALLATION OF FOOT PEDAL

Power On

Follow the steps below to turn on the transmitter:

1. Check to make sure that the battery is fully charged and installed correctly.
2. Toggle the switch to the [ON] position. When active the R.LED will be lit.
3. Connect the receiver to power.
   • For safety always power on the transmitter before the receiver.

Instructions
After setting up, follow the instructions below to operate the system.

1. Automatic code matching (the transmitter and receiver have been successfully coded before leaving the factory.)
   If you need to replace another transmitter or receiver, please follow the following steps to code:

2. When the transmitter power is on and the code matching mode is on, the light keeps flashing;

3. The power supply of the receiving board is turned on, and the front lights keep flashing to enter the code matching mode;

4. When the code matching is successful, all the transmitter lights are on and all the lights on the car are off;
   Note: when code matching, please operate the transmitter to enter the code matching state first, and then operate the receiver to enter the code matching state.

5. POWER OFF
   Follow the steps below to turn off the system:

6. Disconnect the receiver power.

7. Toggle the transmitter’s power switch to the off position.

Transmitter specification

Throttle stick position

Operating the vehicle

1. Step 1: turn on the transmitter, the headlamp of the transmitter will flash and enter the frequency matching mode.
2. Step 2: turn on the receiver switch, the headlight will flash and enter the frequency matching mode.
3. Step 3: when the transmitter and receiver are successful in frequency up, the front lights of the transmitter will be on for a long time, and the front lights of the vehicle will be off.

Setting the Gear Mesh
The gear mesh is the clearance between the pinion and spur gears in your vehicle. If the motor or gearing components are replaced,check that the gears are not meshing too tightly as this may cause premature wear.

Charging the Battery

1. Connect the charger to a USB port then connect the battery to the charger.
2. When charging, the Green LED is flash, when charged, the Green LED is stable.
3. Do not let the battery charge unattended!
4. If the battery or charger is hot, disconnect the battery and charger immediately as this may be caused by an internal short-circuit.Always charge LiPo batteries on non-flammable, heat-resistant surfaces.
   • Always use a LiPo-safe bag or container while charging. Do not allow LiPo cells to overheat at any time. Cells which reach greater than 140 Fahrenheit(60°C) will usually become damaged and will catch fire.
   • Do not charge the LiPo pack while it is still in the model. Never charge or store battery packs in a vehicle.
   • Do not discharge LiPo; doing so will damage the battery.
   • Do not expose LiPo cell to water or moisture at any time.
   • Do not store battery near open flame or heater.
   • Do not assemble LiPo cells or pre-assembled packs together with other LiPo cells or packs.
   • Always store LiPo battery in a secure location away from children.
   • Always remove the LiPo battery if model is involved in any kind of crash.
   • Carefully inspect the battery and connectors for even the smallest damage.
   • CAUTION: Cells may become hot after usage. Allow the pack to cool to room temperature prior to recharging.
   • Do not allow the electrolyte to get into eyes or on skin. Wash affected areas immediately if they if they come into contact with electrolyte. Do not alter or modify connectors or wires of a LiPo battery pack.
   • Always inspect the condition of the battery before charging and operating.
   • Do not short circuit the LiPo battery.
   • Do not have contact with a leaky/damaged battery directly.
   • Do not charge battery out of recommended temperature range(O°C 45°C).

NOTE

1. If it is not in use for a long time, unplug and take off the battery to prevent battery leakage.
2. Do not open, disassemble, or attempt to repair the battery.
3. Please disconnect the battery from the receiver before charging.

Spare parts list

CE Warning
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Appendix 1 FCC Statement

FCC ID: 2AUBX-HT-TX02
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televison reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Caution! The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

1. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-lacated or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
2. Move all your channels to the desired position.
3. Select [All channels] and then [Yes] in the confirmation box.

Declaration of Conformity (DoC)

We, Add: Room701,Block B, Luo Tian Community Xiangshan Road142,Songgang Street,Shenzhen Baoan District China

declare under our responsibility that the product:
Type of Equipment: Driving System & 2.4GHz Control System
Brand Name: ROCHOBBY
Compatiable for cars: 1:18 Mogrich
Equipment Model: 11810

to which this declaration relates is in conformity with the essential requirements and other relevant requirements of the Directive 2014/53/EU, EMC Directive 2014/30/EU, EMC Directive 2014/53/EU, FCC Indentifier 2AUBX-HT-TX02 , EU RoHS Directive 2011/65/EU and Council Directive 2014/30/EU. The product is in conformity with following standards and/or other normative documents:

• ETSI EN 301 489-1 V2.2.3(2019-11)
• ETSI EN 301 489-17 V3.2.4(2020-09)
• EN 55032:2015+A11:2020
• EN 55035:2017+A11:2020
• EN61000-3-2:2014
• EN61000-3-3:2013
• EN : 62479:2010
• ETSI EN 300 328 V2.2.2 (2019-07)

Phone: 0769-86976655
Web:www.rochobby.com

References

• FMS - Leading Creator for RC Airplanes, RC Cars

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>