InHand Networks VT310 Vehicle Localization Gateway Instruction Manual

June 6, 2024
InHand Networks

InHand Networks
Vehicle Tracker VT310
Quick Installation Manual

InHand Networks
www.inhandnetworks.com
Version: V1.0
February, 2020

Copyright © 2019. All rights are reserved by InHand Networks and its licensors. Without the written permission of the Company, no unit or individual is allowed to excerpt, reproduce or transmit in any form part or all of the contents in the manual.

VT310 Vehicle Tracker
Quick Start Guide
V1.0

Structure of VT310

InHand Networks VT310 Vehicle Localization Gateway -
stracture

Installation and Wiring

VT310 comes with a built-in battery. The VT310 device can be powered by a built-in battery or an external DC power supply. Generally, when an external DC power supply is available, the external power supply is preferred.
LTE antenna and GNSS antenna are built-in VT310. Users can use without operation.
The information of the LTE Module: Mode Number: EMS31-X, FCC ID: QIPEMS31-X, IC: 7830A-EMS31X

Installing the SIM card

Before using the device, you need to install the SIM card. When the device is powered on, it will automatically dial up the network.

InHand Networks VT310 Vehicle Localization Gateway - sim
card

Arrow position for SIM card cover. Open the cover and insert the SIM card according to the SIM card direction indicated on the cover.

Power to VT310

3a) Use the external power supply
Connect the positive and negative terminals of the external power supply with X-V+ and X-V- respectively:
b) Use a built-in battery for power
VT310 provides a 1200mAbuilt-in rechargeable battery. When there is no external power input, stable power input can be provided for the equipment.

Confirm Work Status

Confirm by Indicator Status

a) GNSS Indicator (Green)

Function Indicator status
GPS disable OFF
GPS enable FLASH(0.5Hz)
GPS to timing success FLASH(5Hz)
GPS to position success Always on

b) Cellular Indicator (Orange)

Function Indicator status
Module disable OFF
Module enables FLASH(0.5Hz)
Dial succeeded FLASH(5Hz)
Confirm by Configuration Mode

a) Wiring:
Serial port (check-in device Manager after connecting PC with USB to the serial port line) :

InHand Networks VT310 Vehicle Localization Gateway -
port

VT310 devices connect serial ports (cables R232-Tx1, RS232-Rx1, GND connect USB to 232 serial ports) :

b) Open the serial port to enter the Configuration Mode:
Use “SSCOM42”, click open serial port, enter +++ in the character box, and then click Send.
notice:
①The serial port number corresponding to VT310 should be selected; Baud rate:
115200; Data bit: 8; Stop bit: 1; Check bit: None; Asthenosphere control is not supported.
②When sending “+++” into configuration mode, be careful not to check “HEX Send” or “send the new line”.

sscom42.exe

The window enters the configuration mode, then closes the serial port.
Windows Install serial port tools, eg: SecureCRT, as follow configuration:

InHand Networks VT310 Vehicle Localization Gateway -
serial

c) Show work status by command:

i. cellular status
command: cellular status

InHand Networks VT310 Vehicle Localization Gateway -
commond

ii. GNSS status
Command: lbs status

InHand Networks VT310 Vehicle Localization Gateway - commond
1

Connect to Wialon

Wialon – the platform for GPS tracking and IoT.

Configuration to VT310

command: wialonClound set 1

InHand Networks VT310 Vehicle Localization Gateway - commond
2

notice: command to take effect after a restart

Configuration to Wialon

InHand Networks VT310 Vehicle Localization Gateway -
wialon

URL https://hosting.wialon.com/
NAME inhand_free
PWD evan1234

Add VT310 to the Wialon, Please in the order indicated above.
③| user-defined
④| Choose Wialon Combine
⑤| SN

Enters VT310 configuration mode to get SN:

InHand Networks VT310 Vehicle Localization Gateway - commond
3

Confirm Wialon connection status
  1. By command
    Command: wialon statusInHand Networks VT310 Vehicle Localization Gateway -
commond 4Connect success: connected
    Connecting: connecting
    Connect failed: disabled

  2. By Wialon
    Switch to “Monitor”, When the device is online, it appears green; When the device goes offline, it appears grey.InHand Networks VT310 Vehicle
Localization Gateway - wialon 1

Notice

Parameters of Cellular

VT310 supports ordinary card automatic dialing, The default dialing parameter for white CARDS is ”internet auto gprs gprs *99# internet 2 60” . if dial by white CARDS , Please use ”cellular set <apn password> ” to Configure dialing parameters , eg:

InHand Networks VT310 Vehicle Localization Gateway - commond
5

When the configuration is complete, enter the command“ reboot” to restart the device.

ISED STATEMENT
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:

  1. This device may not cause interference; and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

FCC warning:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

Any modification to the product is not permitted unless authorized by InHand Networks. It’s not allowed to disassemble the product. It is not allowed to replace the system or change components unless with permission and certification. Please contact the technical support department of InHand Networks or local branches for help.

RF Exposure Statement
This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 21 cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals