CHAMBERLAIN 956EV 3-button Remote Control User Manual
- June 9, 2024
- CHAMBERLAIN
Table of Contents
CHAMBERLAIN 956EV 3-button Remote Control
For use with Chamberlain 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. The garage door opener activates when the programmed button on the remote control is pressed. The remote control can activate up to three garage door openers.
Make sure the garage door opener has a working light bulb because it is a programming indicator.
WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
GARAGE ACCESS SYSTEM KEYCHAIN REMOTE
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
- ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls.
- Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
- ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
PREPARE
Locate the Program button on the remote control.
PROGRAM THE REMOTE CONTROL
-
Press and hold the program button the remote control until the LED on the front of the remote control turns on.
-
Press and release the remote control button you wish to use the number of times that corresponds with the garage door opener type:
-
To exit programming mode, press any remote control button except the button that was just programmed.
-
Press and release the Learn button on the garage door opener.
The Learn LED will light. Within 30 seconds.
-
Press the remote control button programmed in step 2 until the garage door opener lights flash or two clicks are heard.
-
To test, press the programmed button on the remote control.
BATTERY
The LED on your remote will stop flashing when the battery is low and needs to be replaced. To replace battery, open the case as shown. Insert battery positive side up (+). Replace the battery with only 3V CR2032 coin cell batteries. Dispose of old battery properly.
Pry open the case with a screwdriver blade.
Warning
To prevent possible SERIOUS INJURY or DEATH:
- NEVER allow small children near batteries.
- If the battery is swallowed, immediately notify the doctor.
To reduce the risk of fire, explosion, or chemical burn:
- Replace ONLY with 3V CR2032 coin batteries.
- DO NOT recharge, disassemble, heat above 212° F (100° C), or incinerate.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustments or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER-SERVICEABLE PARTS. This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARRANTY
ONE-YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser of this product that it is free from defects in materials and/or workmanship for a period of 1 year from the date of purchase.
REPLACEMENT PARTS
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20
FAQs
How do I program my remote control to work with my garage door opener?****
First, make sure that your garage door opener is compatible with the remote control. The remote control works with most Chamberlain and Liftmaster Garage Door Openers manufactured after 1993. If you have a Liftmaster Garage Door Opener, refer to the Liftmaster website for programming instructions.
Can I program more than one remote control to work with my garage door opener?****
Yes. You can program up to three remote controls to work with your garage door opener.
How many remotes can be programmed to work with my garage door opener at the same time?****
Only one remote control can be used at a time. If you have more than one remote control, you can program each one to work with your garage door opener. However, only one remote control can be used at a time.
How do I know if my garage door opener is compatible with the remote control?****
First, make sure that your garage door opener is compatible with the remote control. The remote control works with most Chamberlain and Liftmaster Garage Door Openers manufactured after 1993. If you have a Liftmaster Garage Door Opener, refer to the Liftmaster website for programming instructions.
How do I program my remote control to work with my garage door opener?****
First, make sure that your garage door opener is compatible with the remote control. The remote control works with most Chamberlain and Liftmaster Garage Door Openers manufactured after 1993. If you have a Liftmaster Garage Door Opener, refer to the Liftmaster website for programming instructions.
Can I program more than one remote control to work with my garage door opener?****
Yes. You can program up to three remote controls to work with your garage door opener.
Why do some garage door remotes have 3 buttons?****
The garage door is only opened by the single button. One of the three buttons locks the door (if compatible), while the other turns on the light.
How does the remote work for a garage door opener?****
Garage door remote controls operate by transmitting a coded signal to the garage door motor via radio frequency. The garage door will start to raise or drop if this code matches the one on the motor.
Are garage remotes secure?****
They are therefore susceptible to a replay assault. The majority of garage door opener producers converted to rolling code technology after 1993, so the code will vary each time you use your remote.
What frequency is garage remote?****
When you use your remote, it transmits a radio signal over a certain frequency to the opener. The majority of garage door openers operate on frequencies between 300 MHz and 390 MHz, with 300 MHz, 310 MHz, 315 MHz, and 390 MHz being the most popular.
Can any garage remote work?****
Not all remote controls for garage doors are global. A number of variables affect how well a garage door remote control works. There are two versions you should search for if you’re especially seeking for a universal remote for your garage door opener.
Can garage door remotes be hacked?****
An established code is sent across radio frequencies by older garage door openers. One can simply hack into your system and open your garage door if they possess hacking abilities and a code grabber (which captures the code supplied by an opener).
How far can a garage remote work?****
A standard garage door remote has a range of three to five vehicle lengths or around 50 feet.
Can any garage door remote be programmed?****
In most circumstances, you can program a different remote using your current garage door opener remote, but there is a catch. The typical garage door remotes lack such capability.
Download The PDF Link;CHAMBERLAIN 3 button Remote Control pdf
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>