havit HV1834W-12V Klip Inground Light Instruction Manual
- June 4, 2024
- havit
Table of Contents
Klip Inground Light Installation Instructions
Product Specifications
Model No. | HV1834W-12V | HV1834C-12V | HV1834W-240V | HV1834C-240V |
---|---|---|---|---|
Name | Klip | |||
Material | 316 Stainless Steel cover + Aluminium body | |||
Colour | Cover – Stainless Steel I Body – Black | |||
IP Rating | IP67 | |||
Input Voltage | 12v DC | 240V | ||
Protection Class | 41 (Low Voltage) | PO (Requires Earth) | ||
Lamp Base | Built-In LED | |||
Lamp Wattage | lx 30w | lx 30w | ||
Colour Temp | 3000k | 5500k | 3000k | 5500k |
Lumens | 2400Im | 2700Im | 2400Im | 2700Im |
CRI | > 80 | |||
Wiring | Parallel | |||
Dimmable | No | |||
Warranty | 3 Years Replacement* |
Important Safety Issues:
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, the Voltage to fitting must be within +or- 5% of the voltage required, if not within this allowance warranty will be voided.
- Aluminum and 304SS fittings must not be installed within 5km of any saltwater environments.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining)
- All o-rings and seals must be in place correctly to maintain the warranty
- When installing inground light fittings, Adequate drainage must be allowed to prevent fittings from sitting in water for a long period of time, if no drainage is allowed, the Warranty will be voided, See sample adequate drainage diagram for correct installation method.
- This form may be updated at any time due to product improvements, please check the online installation form for the most current version.
Steps for Installation: HV1834-240V
-
Make sure that the electrical circuit is free of voltage (master switch off)
-
Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
-
Insert the canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
-
To connect the cable, strip back cable on both fitting and cable run and twist the earth together first, then positive cables from fitting to positive on the cable run.
Then connect neutral cables from fitting to neutral on cable run. -
Solder all joins using solder and either a heat gun or butane gas torch.
-
Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
-
Heat the heat shrink or crimp the gel cap making sure all connections are covered.
-
Make sure the seals are still in place and screws are tight to avoid any water penetration.
-
Insert fitting into the canister. Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
-
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Steps for Installation: HV1834-12V
- Make sure that the electrical circuit is free of voltage (master switch off)
- Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
- Insert the canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
- Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable – If more than one fitting is installed, wiring must be done in parallel.
- Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Make sure the seals are still in place and screws are tight to avoid any water penetration.
11. Insert fitting into the canister. Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
12. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>