Metra BMW 1 Series Dash Kit Instruction Manual
- June 9, 2024
- Metra
Table of Contents
Metra BMW 1 Series Dash Kit
BMW 1 Series (without NAV, with automatic climate control)
2008-2013
Visit MetraOnline.com for more detailed information
about the product and up-to-date vehicle specific applications
KIT FEATURES
- ISO DDIN radio provision
- Painted scratch resistant matte black to match the factory finish
KIT COMPONENTS
- A) Radio housing
- B) Radio brackets
- C) Switch panel cover
- D) Ribbon cable
- E) Panel clips
- D) Phillips screws (8)
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Please visit metraonline.com for
wiring harness options
Antenna Adapter: 40-EU10
TOOLS REQUIRED
- Panel removal tool
- Phillips screwdriver
- Cutting tool
Attention! With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product.
DASH DISASSEMBLY
- Unclip and remove the dash trim panel above the radio and glove box.(Figure A)
- Unclip the climate control panel then unplug and remove. (Figure B)
- Remove (2) screws securing the bottom of the radio, then unplug and remove the radio. (Figure C)
- Unclip the climate controls from the climate control panel and save for reassembly. (Figure D)
- Unclip and remove the switch panel below the climate controls (if equipped) (Figure E).
KIT PREPARATION
-
Using a cutting tool, remove the sections of sub-dash indicated to provide clearance for the radio and climate controls. (Figure A)
-
Install the (2) panel clips to the radio housing.
For models with a switch panel below the climate control. -
Remove (5) screws securing the switch panel back plate, then remove the switch panel circuit board.
-
Unplug the ribbon cable from the circuit board. (Figure B)
-
Attach the White connector from the ribbon cable supplied with the kit to the circuit board.
-
Reinstall the circuit board back into the switch panel.
-
Clip the climate control panel, and switch panel, into the radio housing. (Figure C)
-
Attach the Black connector from the ribbon cable to the climate control panel. (Figure D)
For models without a switch panel below the climate control. -
Clip the switch panel cover to the radio trim panel.
-
Disregard the ribbon cable, it will not be used in this application.
KIT ASSEMBLY
ISO DDIN radio provision
-
Attach the radio brackets to the radio using the screws supplied with the radio. (Figure A)
Note: Radio mounting screws must be flush with the mounting brackets. Countersunk flat-head screws have been provided if needed. (Figure A) -
Locate the factory wiring harness and connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for
proper operation. -
Secure the completed assembly into the dash with the factory screws.
-
Reassemble the dash in reverse order of disassembly using radio trim panel assembly to complete the installation.
Having difficulties? We’re here to help.
Contact our Tech Support line at:
386-257-1187
Or via email at:
techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday – Friday: 9:00 AM – 7:00 PM Saturday: 10:00 AM – 7:00 PM Sunday:
10:00 AM – 4:00 PM
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most
recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or
call
800-354-6782 for more information and
take steps toward a better tomorrow.
Metra recommends MECP certified technicians
Metra. The World’s Best Kits.®
MetraOnline.com
© COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>