POTTER SCM24W-75110 Select-A-Strobe Chime Combination Owner’s Manual
- June 9, 2024
- POTTER
Table of Contents
POTTER SCM24W-75110 Select-A-Strobe Chime Combination
Feature
- Meets or exceeds NFPA/ANSI Standards and ADA Accessibility Guidelines
- UL Listed for wall mounting
- Screw terminal capacity up to AWG #12
- Universal mounting plate included
- Selectable settings: 75cd or 110cd
- Polarized strobes with wide operating voltage range using filtered DC or unfiltered FWR input voltage
- Horn field selectable tones:
- 2700 Hz or 2400 Hz
- Temporal or Non-temporal
- High or Low dBA Output
- Mounts to 4” square, single gang, double gang, or octagonal back box
- Tamper-proof candela selector switch
- Synchronization requires Sync Module (SMD10-3A)
- Available in red or white housing
Description
Amseco’s Select-A-Strobe/Chime Series is designed to provide audible (private
mode) for fi re alarm protection systems. It complies with ADA and meets or
exceeds NFPA/ANSI audible emergency evacuation signal and UL 464 (private
mode) 1971. The SCM24W Series features a unique candela intensity field
selector switch for alternating the candela output 75cd to 110cd. The chime
provides two different field selectable tones and a high/low output setting
that can be achieved with the use of mini-jumpers located on the back of the
unit. These appliances are polarized for connecting to supervised fi re alarm
circuits. The strobe is designed with a xenon flash tube and provides a
candela intensity field selector switch for maximum performance.
The SCM24W-75110 can be synchronized by using the SMD10-3A Sync Module to
comply with NFPA recommendations concerning photosensitive epilepsy when
installing two or more visual appliances within the field of view. The strobe
signals are listed for indoor use, wall mount, under UL1971 standard.
Ordering Information
Model Number| Stock Number| Housing Color| Input Voltage| Operating Voltage
Range| Selectable Strobe Out- put (cd)| Horn Sound Ouput| Wiring Type|
Mounting Type| Operating Temperature Range
---|---|---|---|---|---|---|---|---|---
SCM24W-75110R| 4580011| Red| Regulated 24V DC/ FWR| 16-33 VDC
16-33 VFWR
| 75 or 110| Selectable| Terminals| Wall| 32°F – 120°F (0°C – 49°C)
SCM24W-75110W| 4580012| White
Engineering Specifications
The audible and visual alarm indicating appliances shall be Amseco model SCM24W-75110 or equivalent device. The chime shall be listed under UL 1971 Standard for signaling devices for the hearing impaired and shall be approved for fi re protective service. The candela output shall be field selectable, having a dual setting of 75cd or 110cd output. The chime shall provide two different field selectable temporal or steady tones, and a high/low field selectable output setting. The signaling strobe shall operate on a 24V DC non- coded regulated DC supply or full wave rectified, unfiltered supply. The chime may operate on a 24V DC coded system. The strobe shall be designed to produce one signal flash per second with continuously applied minimum voltage. The strobe/chime shall have a universal back mounting plate, capable of wall mounting to a back box. When strobe synchronization is required, the strobe/chime shall be compatible with Amseco SMD10-3A (daisy chain) or other source of Amseco sync protocol. Audible and visual signaling devices shall be installed in accordance with current NFPA guidelines.
Mounting
Sound Output Dispersion | Horizontal (dB) | Vertical (dB) |
---|---|---|
DEGREES | +90 | -6 |
+60 | -2 | -2 |
+30 | -1 | -1 |
0 | 0 | 0 |
-30 | -1 | -3 |
-60 | -2 | -5 |
-90 | -6 | -6 |
Strobe Light Only | Max. RMS operating Current (mA) | |
--- | --- | |
Regulated 24V DC | Regulated 24V FWR | |
75cd | 137 | 190 |
110cd | 189 | 256 |
Tone Selection | PC3 | |
Pattern | PC2 | |
Tone | PC1 |
Volume
---|---|---|---
Jumper| | Non- Temporal| 2700 Hz| High
| Temporal| 2400 Hz| Low
WARNING Strobes must be used only on circuits with continuously operating voltage. DO NOT use strobe on coded or interrupted circuits in which the applied voltage is interrupted ON and OFF as the strobe may fail to flash. The applied voltage must be within its rated input voltage range. Fuse ratings on signaling circuits must handle peak currents from all devices connected to those circuits.
Customer Support
Potter Electric Signal Company • 2081 Craig Road, St. Louis, MO, 63146-4161 • Phone:800-325-3936/Canada 888-882-1833 • www.pottersignal.com
References
- Fire Alarm Resources | Download fire alarm documents
- Potter Electric: Fire Alarms & Fire Sprinkler Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>