THE HOME DEPOT A02894 Modern Black Chandelier Candlestick Island 5-Light Pendant Light Installation Guide

: June 9, 2024
: THE HOME DEPOT

Table of Contents

IMAGE FOR FINISHED PRODUCT
PARTS TYPE & QTY INCLUDING
ASSEMBLY & INSTALLATION INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

THE HOME DEPOT A02894 Modern Black Chandelier Candlestick Island 5-Light Pendant Light Installation Guide

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

We suggest installation by a licensed electrician.
Please read the instruction carefully and save it as you may need it at later time.
Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

(bA) Hex nut (1)
(C) Threaded nipple (2)
(E) Single bar (1)
(F) Green ground screw (1)
(G) Canopy (1)
(H) Collar ring (1)
(I) Collar loop (1)
(J) Quick link (2)
(K) Chain (1)
(L) Loop (1)
(M) Wire house (1)
(N) Candle sleeving (5)
(O) Socket base (5)
(P) Arm (5)
(Q) Trim (1)
(R) Finial (1)

ACCESSORIES & QTY ENCLOSED

(B) Mounting screw (2)
(D)Plastic wire connector (3)

Line art shown may not exactly match the fixture enclosed. However, the installations do apply to this fixture.

ASSEMBLY & INSTALLATION INSTRUCTIONS

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration
Make assembly
If the group of parts are not already assembled:

Step A1: Thread the single bar(E) over the threaded nipple (C) a minimum of 6 mm (1/4”). At this point need note that: the side of single bar marked “GND” must face to the down.
Step A2: Thread the hex nut (A)onto the threaded nipple (C) to secure the single bar (E) in place.
Step A3: Thread the collar loop (I) onto another end of threaded nipple (C).
Make pre-installation

Step B1: Thread the loop (L)onto the wire house (M) till tight . Thread the threaded nipple (C) onto the round metal plate ,then carefully push the lower tirm over the threaded nipple (C) ,secure with finial (R ) Position the socket base (O)over the socket,then position the candle sleeve (N)over the socket
Step B2: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the remaining chain.
Step B3: Open the quick link (J) to connect the loop of top trim (L) and the chain (K), Close the quick link (J).
Step B4: Carefully lace the wires through the chain (K)(every other link)and stop just before you reach the top of chain (K). Gently pull the wires till snug .
Turn off power
Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done.
A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the“OFF” position
Make installation

Step C1: .Attach the single bar (E) to outlet box with mounting screws (B). The side of single bar marked “GND” must face out Unscrew the collar ring (H) from the collar loop Step C2: Pass canopy (G) over the collar loop (I) then secure with collar ring (H) to test the height .Unscrew collar ring (H) from collar loop (I) and remove the canopy (G).
Note: The canopy (G) should be snug against the ceiling and the collar loop (I) should be screwed enough threads (no less than 6 threads )over the threaded nipple (C) for more secure hanging .If not, adjust the height of threaded nipple (C) and collar loop (I) until the desired height is reached. Remove the collar ring (H) and canopy (G) and place to the side.
Step C3: Slip the collar ring(H) over the chain(K),then do the same with the canopy(G)
Step C4: Open the quick link(J)，attach the quick link (J) to connect the collar loop (I). Close the quick link(J) Pass the wires through the collar loop(I) to the top of nipple(E) and gently pull till snug.
Step C5: If needed, cut off the wires length of fixture.At this point, the remaining wire length measured from the top of single bar(B) should be at least 6″.
Step C6: Make wire connections Connect wires as below wires connecting shown. TAKE NOTE OF YOUR COLOR OF FIXTURE ,NEVER CONNECT

WIRES TO GROUND WIRES
Connect ground wire according to below chart

INSTRUCTIONS

Connect Black orRed Supply Wire to:| Connect
White Supply Wire to:
---|---
Black| White
Parallel cord ( round & smooth )| Parallel cord ( square & ridged )
Clear,Brown,Gold or Blackwithout tracer| Clear,Brown,Gold or Blackwith tracer
Insulated wire ( other than green) with copper conductor| Insulated wire ( other than green ) with silver conductor

*Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus. )

Twist plastic wire connector until wires are tightly joined together,wrap each connector with approved electrical tape.Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box .

Step C7: Raise canopy (G) to ceiling and secure canopy (G) in place by tightening threaded ring (H) onto collar loop (I)

Step C8 : Install bulbs (not included) (Please do not exceed the maximum capacity recommended on the socket.) Adjust the arms to their proper positions

Check everything is already installed properly, then you could turn on the light. Enjoy!

CLEANING
To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.