Klipsch 1071286 The Nines Heritage Inspired Powered Speakers User Manual
- June 9, 2024
- Klipsch
Table of Contents
- INSIDE
- PRIMARY SPEAKER (ACTIVE)
- QUICK SETUP – INSTALL THE KLIPSCH CONNECT APP
- CONNECTIONS – HDMI-ARC
- REMOTE
- BLUETOOTH® WIRELESS TECHNOLOGY
- LED SOURCE INDICATOR
- CARE AND CLEANING
- DYNAMIC BASS EQ
- FACTORY RESET
- REMOTE CONTROL CODES
- TROUBLESHOOTING
- POWERED SPEAKERS/MUSIC SYSTEMS WARRANTY
- PRODUCT REGISTRATION
- Documents / Resources
THE NINES
INSIDE
- Speakers (2)
- Remote
- Batteries
- Main Power Cord
- HDMI Cable
- USB Cable
- Speaker Cable
PRIMARY SPEAKER (ACTIVE)
- Source Control/LED Source Indicator
- Volume Control
- Phono Input
- Phono/Line Switch
- Auxiliary 3.5mm Input
- Subwoofer Output
- Optical Input
- USB Audio Input
- Secondary Speaker Out
- Ground Screw Terminal
- Service Port
- HDMI ARC
- POWER
- VOLTAGE SELECTOR
SETUP
QUICK SETUP – INSTALL THE KLIPSCH CONNECT APP
Getting Started Product Registration Virtual Remote Control and EQ
CONNECTIONS – HDMI-ARC
(IF TV HAS NO HDMI-ARC OUT SEE NEXT PAGE)
A Basic TV HDMI input will not transfer the TV audio signal to the
speakers. The speakers must be connected to the TV’s HDMI-ARC output, optical
output, or analog audio output in order to receive TV Audio.
CONNECTIONS – TV
- Your TV will need to be set to PCM (or Stereo Only)
CONNECTIONS – COMPUTER
CONNECTIONS – TURNTABLE
REMOTE
IR REMOTE CONTROL CODES
ON / OFF | 0x 807F 1AE5 |
---|---|
Mute | 0x 807F 01FE |
Subwoofer Level Up | 0x 807F 07F8 |
Subwoofer Level Down | 0x 807F 0AF5 |
Volume Up | 0x 807F 03FC |
Volume Down | 0x 807F 06F9 |
TV / ARC | 0x 807F 19E6 |
Subwoofer Level Reset | 0x 807F 3EC1 |
Play/Pause | 0x 807F 21DE |
Phono Source Select | 0x 807F 0FF0 |
Auxiliary Source Select | 0x 807F 0EF1 |
Digital Optical Source Select | 0x 807F 0CF3 |
USB Source Select | 0x 807F 12ED |
Bluetooth® Source Select | 0x 807F 0DF2 |
ON / OFF
Mute
Subwoofer Level Up
Subwoofer Level Down
Volume Up
Volume Down
Subwoofer Level Reset| TV
Play/Pause
Phono Source Select
Auxiliary Source Select
Digital Optical Source Select
USB Source Select
Bluetooth® Source Select
---|---
BLUETOOTH® WIRELESS TECHNOLOGY
PAIR Hold 3 Seconds
Example only. Your device may differ.
SUBWOOFER OUTPUT
LED SOURCE INDICATOR
Bluetooth® Input
Phono Input
Auxiliary Input| Optical Input
USB Audio Input
TV
---|---
SELECT SOURCE
NOTE: You may notice slightly different volume levels between different
sources.
This is by design to ensure optimal gain structure from source to source.
CARE AND CLEANING
* USE MICROFIBER CLOTHS ONLY
DYNAMIC BASS EQ
Dynamic Bass EQ applies loudness correction to automatically adjust low frequency levels as volume changes.
For best results, increase input source volume to maximum.
DISABLE DYNAMIC BASS EQ
ENABLE DYNAMIC BASS EQ
FACTORY RESET
NOTE Factory Reset will clear the Bluetooth ® pairing history
REMOTE CONTROL CODES
(FOR UNIVERSAL OR CABLE REMOTES)
RCA- | 41609 OR 43915 |
---|---|
DIRECTV | 31609 |
XFINITY*- | 30531 OR 31023 |
BRIGHT HOUSE | 288 |
AT&T (SILVER) | 5156 OR 5023 |
AT&T (BLACK) | 5156 |
- MUST HAVE AUDIO/AUX BUTTON OR AUDIO·SB BUTTON
RED CENTER BUTTON
NOTE:** NOT ALL UNIVERSAL REMOTES ARE COMPATIBLE
HEX CODES – SET 1
VOLUME UP| Ox 856A 9F60
VOLUME DOWN| Ox 856A 9E61
MUTE| Ox 856A 9966
HEX CODES – SET 3
VOLUME UP| Ox A55A OAFS
VOLUME DOWN| Ox A55A OBF4
MUTE| Ox A55A 12ED
HEX CODES – SET 4
VOLUME UP| Ox 859A 817E
VOLUME DOWN| Ox 859A 82ND
MUTE| Ox 859A 8778
TROUBLESHOOTING
For more in-depth information and troubleshooting instructions visit Klipsch.com
IMPORTANT SAFETY INSTRUCTIONS!
- READ these instructions.
- KEEP these instructions.
- HEED all warnings.
- FOLLOW all instructions.
- DO NOT use this apparatus near water.
- CLEAN ONLY with dry cloth.
- DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- ONLY USE attachments/accessories specified by the manufacturer.
- USE ONLY with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- UNPLUG this apparatus during lightning storms or when unused for long periods of time.
- REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus.
- To completely disconnect this apparatus from the AC Mains, disconnect the power supply wall wart from the AC receptacle.
- The mains plug/appliance coupler is used as a disconnect device, the disconnect device shall remain readily operable.
- DO NOT overload wall outlets or extension cords beyond their rated capacity as this can cause electric shock or fire.
The exclamation point, within an equilateral triangle, is intended to alert
the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
** The lightning flash with arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electrical shock to persons.
WARNING: To reduce the risk of fire or electrical shock, do not expose
this apparatus to rain or moisture.
WARNING: No naked flame sources – such as candles – should be placed on
the product.
WARNING: Do not place batteries in mouth or ingest. Chemical burn hazard.
Keep new and used batteries out of reach of children and pets. If swallowed,
it can cause severe internal burns in just 2 hours and can lead to death.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
WARNING: If battery compartment does not close securely, stop using the
product and keep it away from children and pets.
WARNING: Do not handle leaking or damaged batteries.
WARNING: Risk of leakage. Only use the specified type of batteries. Never
mix new and used batteries. Observe correct polarity.
Remove batteries from products that are not in use for extended periods of
time. Store batteries in a dry place.
WARNING: Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
WARNING: Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type.
WARNING: Do not recharge non-rechargeable batteries.
WARNING:** Avoid exposure to extreme heat or cold.
Please dispose of any used batteries properly, following any local
regulations. Do not incinerate.
WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this
equipment are hazardous to life. No user-serviceable parts inside. Refer all
servicing to qualified service personnel. Place the equipment near a main
power supply outlet and make sure that you can easily access the power breaker
switch.
WARNING: This product is intended to be operated ONLY from the AC
Voltages listed on the back panel or included power supply of the product.
Operation from other voltages other than those indicated may cause
irreversible damage to the product and void the products warranty. The use of
AC Plug Adapters is cautioned because it can allow the product to be plugged
into voltages in which the product was not designed to operate. If the product
is equipped with a detachable power cord, use only the type provided with your
product or by your local distributor and/or retailer. If you are unsure of the
correct operational voltage, please contact your local distributor and/or
retailer.
EU COMPLIANCE INFORMATION
Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive
2006/95/ EC; European Union EMC Directive 2004/108/ EC; European Union
Restriction of Hazardous Substances Recast (RoHS2) Directive 2011/65/ EC;
European Union WEEE Directive 2002/96/ EC; European Union Eco-Design Directive
2009/125/EC; European Union Registration, Evaluation, Authorization and
Restriction of Chemicals (REACH) Directive 2006/121/EC; European Union Radio
and Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC.
This product contains batteries that are covered under the 2006/66/EC European
Directive, which cannot be disposed of with normal household waste. Please
follow local regulations. You may obtain a free copy of the Declaration of
Conformity by contacting your dealer, distributor, or Klipsch Group, Inc.’s
worldwide headquarters.
Contact information can be found here: http://www.klipsch.com/Contact-Us
WEEE NOTICE
Note: This mark applies only to countries within the European Union (EU)
and Norway.
This appliance is labeled in accordance with European Directive 2002/96/EC
concerning waste of electrical and electronic equipment (WEEE). This label
indicates that this product should not be disposed of with household waste. It
should be deposited at an appropriate facility to enable recovery and
recycling.
FCC AND CANADA EMC COMPLIANCE INFORMATION
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Approved under the verification provision of FCC Part 15 as a Class B Digital
Device.
Caution: Changes or modifications not expressly approved by the
manufacturer could void theuser’s authority to operate this device.
Caution: To comply with the limits of the Class B digital device,
pursuant to Part 15 of the FCC Rules, this device is to comply with Class B
limits. All peripherals must be shielded and grounded. Operation with non-
certified peripherals or non-shielded cables my result in interference to
radio or reception.
This Class B digital apparatus complies with Canadian ICES-003. CAN ICES-3
(B)/NMB-3(B)
WIRELESS TRANSMITTER COMPLIANCE INFORMATION
The term “IC:” before the radio certification number only signifies that
Industry Canada technical specifications were met.
This device complies with part 15 of the FCC Rules and the applicable Industry
Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with FCC and IC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This product can be used in a tropical climate of 40 degrees Celsius and
2000m.
The fuse could be in the neutral of the mains supply and after operation of
the fuse, parts of the equipment that remain energized are at ES3 level during
servicing, the fuse may be in the neutral, and that the mains shall be
disconnected to de-energize the phase conductors.
THE NINES
FIRMWARE VERSION 0.0.0.0
Bluetooth Operating Frequency: 24022480MHz
Maximum RF
Power: 4 dBm
(e.i.r.p)
POWERED SPEAKERS/MUSIC SYSTEMS WARRANTY
OPT-1
WARRANTY – U.S.
Klipsch Group, Inc, (KGI) warrants to the original retail purchaser that this
product is to be free from defective materials and workmanship for a period of
two (2) years from the date of purchase, if it is properly used and
maintained. If this product proves defective in either material or
workmanship, KGI, at its option, will (a) repair the product, or (b) replace
the product, at no charge for parts or labor. If the product model is no
longer available and cannot be repaired effectively or replaced with an
identical model, KGI at its sole option may replace the unit with a current
model of equal or greater value. In some cases, modification to the mounting
surface may be required where a new model is substituted. KGI assumes no
responsibility or liability for such modification. To obtain a repair or
replacement under the terms of this warranty, please return to dealer first,
if possible, and the dealer will direct you accordingly for repairs or
replacement. You will be required to submit a copy of the original receipt.
Return shipping for exchanges/repairs is the sole responsibility of the
original retail purchaser.
Limitations:
- This limited warranty does not cover failure of the product resulting from improper installation, misuse, abuse, accident, neglect, mishandling, or wear from ordinary use or environmental deterioration.
- This limited warranty does not cover cosmetic damage, including paint damage, or consequential damage to other components or premises which may result for any reason from the failure of the product.
- This limited warranty is null and void for products not used in accordance with KGI’s instructions.
- This limited warranty is null and void for products with altered or missing serial numbers and for products not purchased from an authorized dealer.
- This limited warranty terminates if you sell or otherwise transfer this product to another party.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE, JURISDICTION TO JURISDICTION OR COUNTRY
TO COUNTRY. KGI’S RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN HARDWARE IS
LIMITED TO REPLACEMENT OR REPAIR AS SET FORTH IN THIS WARRANTY STATEMENT. ALL
EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED IN TIME TO THE TERM OF THIS WARRANTY. SOME STATES,
JURISDICTIONS OR COUNTRIES DO NOT ALLOW THE EXCLUSION OF CERTAIN IMPLIED
WARRANTIES OR CONDITIONS, OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY OR
CONDITION LASTS, SO THIS LIMITATION MAY NOT APPLY TO YOU. KGI DOES NOT ACCEPT
LIABILITY FOR SPECIAL, INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES,
INCLUDING WITHOUT LIMITATION, ANY LIABILITY FOR THIRD PARTY CLAIMS AGAINST YOU
FOR DAMAGES OR FOR PRODUCTS NOT BEING AVAILABLE FOR USE. THE MAXIMUM LIABILITY
FOR WHICH KGI MAY BE RESPONSIBLE WILL BE NO MORE THAN THE AMOUNT YOU PAID FOR
THE PRODUCT THAT IS THE SUBJECT OF THE CLAIM. SOME STATES, JURISDICTIONS OR
COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU.
WARRANTY OUTSIDE THE U.S.
The Warranty on this product shall comply with applicable law when sold to a
consumer outside of the United States.
To obtain any applicable warranty service, please contact the dealer from
which you purchased this product, or the distributor that supplied this
product.
PRODUCT REGISTRATION
Register your product online at www.klipsch.com/register
- Keep up-to-date on new products and promotions.
- Your personal information will never be resold.
- This registration information is not used for warranty purposes.
Please retain your receipt for warranty cla ims.
KEEPERS OF THE SOUND
3502 WOODVIEW TRACE, INDIANAPOLIS, IN, USA
KLIPSCH.COM ****
©2022, Klipsch Group, Inc. Klipsch Group, Inc. is a wholly-owned subsidiary
of Voxx International Corporation.
Klipsch and Keepers of the Sound are trademarks of Klipsch Group, Inc.,
registered in the United States and other countries.
The Bluetooth® word mark is a registered trademark owned by Bluetooth
SIG,
Inc. and any use of such mark by Klipsch Group, Inc. is under license.
V01 – 220511
Documents / Resources
|
Klipsch 1071286 The Nines Heritage Inspired Powered
Speakers
[pdf] User Manual
1071286 The Nines Heritage Inspired Powered Speakers, 1071286, The Nines
Heritage Inspired Powered Speakers, Inspired Powered Speakers, Powered
Speakers
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>