Starline EL203 TWS Earbuds User Manual

Starline EL203 TWS Earbuds

SAFETY PRECAUTIONS

Read these safety instructions before using your device and store them for possible future reference.

• The device should not be exposed to dripping or splashingwater.
• CAUTION: Danger of explosion if battery is incorrectly replaced or not replaced by the same type or equivalent.
• The battery should not be exposed to excessive heat such as sunshine, fire or similar.
• If the battery is worn, it must be removed from the product.
• The battery must be disposed of safely. Always use the collection bins provided to protect the environment.
• The battery cannot be replaced by the user.

SPECIFICATIONS

• Model: EL203/ PO20111
• Wireless Version : V 5.1
• Wireless Range: 10meters
• Earbud Battery: 30mAh
• Charging Case Battery: 300mAh
• Playtime: Up to 2-3 hours
• Charging time: approx 2 hours
• Standby time: 100 hours

Accessories

• 1 User Manual
• 1 Micro USB Charging Cable

TURNING ON/ OFF/ PAIRING

The earbuds will automatically power on after being taken out of the charging case. Simultaneous sound prompt “Boom” sound, (or press and hold two earbuds for 1.5 seconds, and the sound prompts “power on-Boom”). The red and blue lights flash alternately. To power earbuds OFF, put the earbuds into the charging case then close it (or press and hold both earbuds for 3 seconds) at the same time with the sound of “power off” when the earbud placed into charging case. The red led light is on, (or the red light flashes three times to shut down). The earbuds will automatically shut down within 5 minutes without connection.

1. When the two earbuds are taken out of the charging case, they will be automatically paired.
   The success sound “boom”.

2. Turn on the wireless of the mobile phone, search for “EL203” then click connect. After the connection is successful, you will hear “connected” and the indicator light flashes blue every 5 seconds.

3. Turn off the wireless on the mobile phone or turn off the earbuds, you will hear “disconnected”.

4. After the earbud is taken out of the charging case again, it will automatically turn on and connected with the mobile phone wireless.

CHARGING

When the power of the earbuds is low, you will hear “please charge” and red indicator light flashes twice every 5 seconds. Put earbuds back into charging case. The LED on earbud is red while charging in the case, it will turn blue when the earbud is fully charged. When the battery of charging case is low, blue light flashes. Use the Micro USB charging cable to recharge the charging case, charging case battery indicator % will be flashing until it is 100% fully charged.

Earbuds Function Sensor

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
   Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment.

FCC ID : 2AXR6-EL203
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

SAFETY WARNING AVERTISSEMENT!

In order to prevent conditions that can lead to overheating, please make sure that the wireless charging pad surface is free of all metal objects at all times, such as coins or paper clips. In addition, before charging, please remove anything metallic attached to the back of the phone, such as battery cases, ring holders, or plates used for mounting to magnetic phone holders.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>