Lorelli RIMINI DI MARE Car Seat Instruction Manual

RIMINI DI MARE Car Seat
Car seat Group 0/0-10. kg
Instruction Manual

RIMINI DI MARE Car Seat

https://lorelli.eu/media/documents/products/Car%20Seats/RIMINI%20DI%20MARE_Manual%20Instruction.pdf

Scan the QR code to get more product information and manual instruction in more languages. Download QR Scanner App onto your device. SRB/HR/ME/BIH

CAR SEAT

|
---|---
|

NOTICE

1. This is a ‘Universal’ child restraint. It is approved to Regulation No 44, 04 series of amendments, for general use in vehicles and it will fit most, but not all, car seats.
2. A correct fit is likely if the vehicle manufacturer has declared in the vehicle handbook that the vehicle is capable of accepting a ‘Universal’ child restraint for this age group.
3. This child restraint has been classified as ‘Universal’ under more stringent conditions than those which applied to earlier designs which do not carry this notice.
4. If in doubt, consult either the child restraint manufacturer or the retailer.

Only suitable if the approved vehicles are fitted with 3 point / with retractor safety belts, approved to UN/ECE Regulation No 16 or other equivalent standards.’
EXTREMELY DANGEROUS! Do not place rear-facing child seat on front seat with airbag. Death or serious injury can occur.

Important safety instructions!

Please read the instructions carefully, because improper installation may cause serious injury, in this case, manufacturer the is not responsible.

1. WARNING! The car seat can not be used forward facing!
2. WARNING! The rigid items and plastic parts of a child restraint shall be so located and installed that they are not liable, during everyday use of the vehicle, to become trapped by a movable seat or in a door of the vehicle. Prevent harness/vehicle belt from getting trapped between car doors or rubbing against sharp parts of the seat or body.
3. WARNINGIAIl straps holding the restraint to the vehicle should be tight, all straps restraining the child should be adjusted to the child’s body. The straps should not be twisted! Always make sure that the seat harness and vehicle belt are correctly tensioned to ensure maximum protection for your child.
4. WARNING! The device should be changed when it has been subject to violent stresses in an accident. After an accident, replace your child restraint and the vehicle seat belts. Although they may look undamaged, they may not protect your child as well as they should.
5. WARNING! Follow closely the instructions for installation. Failure can result in injury to the child!
6. WARNING! It is dangerous to make any alterations or additions to the device without the approval of the Type Approval Authority. Your child is in danger if you don’t follow closely the installation instructions provided by the child restraint manufacturer.
7. WARNING! Your child seat can only be fitted into the passengers seat of a car with a lap and diagonal seat belt. Do not use any load bearing contact points other than those described in the instructions and marked in the child restrained. Ensure the vehicle seat belt buckle is connected to the correct main load bearing contact point which is intended for the occupied vehicle seat. Ensure the buckle and the seat belt of the vehicle are not interfere with the main load bearing contact points of the child restrained system. Ensure you are following the correct way of the vehicle’s safety belt by the installation of the restrained system and by the restraining of the child. On this way you will avoid an unsatisfactory position of the adult safety belt buckle relative to the main load bearing contact points on the restraint. Please contact the child restraint manufacturer if in doubt about this point. The satisfactory position of the adult safety-belt buckle relative to the main load bearing contact points on the restraint is as the following picture16
8. WARNING! Rearward child restraint systems should not be used in seats protected by an airbag.
9. WARNING! NEVER leave your child unattended in the safety device, even for the shortest time!
10. WARNING! Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.
11. WARNING! Donotuse the child restraint system without the cover.
12. WARNING! Do not replace the seat cover with any other than the one recommended by the manufacturer, because the cover constitutes an integral part of the restraint performance.
13. WARNING: DO NOT attempt to dismantle, modify or add to any part of the child restraint system or change the way your vehicle seat belts are made or used.
14. WARNING! Install the child restraint in vehicle seating positions categorized as ‘Universal’ in the vehicle owner’s manual, by using the primary belt route.
15. WARNING! If the chair is not provided with a textile cover, keep it away from sunlight, otherwise it may be too hot for the child’s skin. If the vehicle has been left in the sun for a long time, check the seat cover and make sure it is not too hot before placing the child in the child cushion.
16. WARNING! Do not use the car seat in the house. It is not designed for home use and should only be used in the vehicle!
17. WARNING! Periodically check the belts for wear, paying special attention to the points of attachment, protections and regulating devices. If the harness / vehicles belts becomes cut or frayed, replace it before traveling.
18. WARNING: ALWAYS secure your child with the safety belts when using the car seat.
19. WARNING! Do not leave the buckle in a partially closed position and it must only lock when all parts are engaged. It must be possible to release the child from the restraint immediately in an emergency. Your child must be taught never to play with the buckle. The buckle is NOT CHILD PROOF
20. WARNING! The baby seat must be secured with car safety belt, even when itis notin use. An unsecured seat may injure other passengers in the car in an urgent stop.
21. WARNINGI Store this child seat in a safe place when it is not being used. Avoid placing heavy objects on top of it. Do not allow your child seat to come into contact with corrosive substances e.g. battery acid.
22. WARNING! Do not leave your child in this safety seat for a long period of time. By long trips make more breaks and take out the child from the safety seat.
23. WARNING! Security is only guaranteed if the child restraint is fitted in accordance with these instructions.
24. WARNING! The instruction must be retained on the child restraint for its life period
25. WARNING! Images on the title page and in the instruction manual are only illustrative and may differ from the real product.

WASHING INSTRUCTIONS

1. The car seat can be cleaned using lukewarm water and soap. Do not use aggressive cleaners like abrasives or thinner.
2. The cover should be washed by hand at a maximum temperature of 30°C. Do not put in the dryer, just airing it.
3. The plastic parts can be cleaned by using a wettish drapery. Please, do not use any solvate.

TYPES OF APPROVED BELTS TO HAVE IN THE CAR
Your child seat can be installed ONLY with the help of 3-point belts!!! ONLY in the OPPOSITE direction of movement of the car!
Possibility to install ONLY on seats with 3-point seat belts! CAN NOT BE USED FOR SEATS with 2-point belt!
Parts
Picture 1

Check the height of the shoulder belts
Always check that the shoulder belts are placed at the correct height for your child. Select the height of the straps according to the child’s height. The position of the straps should be at or slightly above the shoulders of the child. Warning: Do not place the straps too high or so that the child can lean on them!
In the back of the safety seat , there are 2 pairs of holes , which can be used to adjust the shoulder straps to suit your child’s weight (Fig. 2)
Adjusting the height of seat belts

1. Press the button for belts adjusting “5” and at the same time pull both shoulder straps. (Picture 3)
2. Take out the belts “11” of the holes on the back from the front of the seat.
3. Place back the belts in the desired holes on the front side of the backrest and connect them behind the back with the adjusting strap “4″. Make sure the straps are placed on the same level and are not twisted.

Fastening the seat belt

1. Combine the two pieces “E”and “F” at the end of the belt (Picture 6) and place them in the central buckle “3” until it clicks into place. (Picture 7)
2. Make sure the belt is locked by pulling the shoulder straps up. (Picture 8)
3. To release belt, press down the red button on the central buckle “3”.

Adjusting the length of the belts

1. Slack the belts: Press the button for belts adjusting “5” and at the same time pull both shoulder straps.  (Picture 3)
2. Tightening the belt: Place your child in the seat, fasten both belts in the buckle in the center and pull the strap “4″ in the middle of the seat. (Picture 5)

Adjusting of the carry handle
The carry handle of the car seat , can be adjusted in 3 stable positions.
To adjust the handle ,please press the red button on handle on both side at the same time. Now it can be rotated. (Picture 9)

1. Position – Straight up for carrying. (Picture 10)
2. Position – Handle clicked back to initiate the rocking feature . (Picture 11)
3. Position – Down to support baby for feeding. (Picture 12)

Ensure that the handle is locked in a position ,the harness is correctly fitted and buckle fastened before carrying your car seat.

INSTALLATION OF SEAT

“Group 0” / newborn and weighing up to 10 kg. /
Please use 3-point safety belts of the car to ensure the safety of the child and to secure the child seat!
Your child seat can be installed ONLY with the help of 3-point belts!!! ONLY in the OPPOSITE direction of movement of the car!
Step 1. Push button “1“ and take out the metal bracket “2“ from the front side under the bottom of the car seat. Picture 13
Step 2. Adjust the handle to the upright position . (Picture14)
Step 3. Place the child seat on the seat of the car in the OPPOSITE direction of movement of the car, ensuring it is firmly pressed against the car seat backrest. If your car has an air bag on the passenger seat, the child seat should be used only in the rear of the car!
Step 4. Slide the lap belt of the vehicle’s 3-point seatbelt through both Lap belt guides .Let the tongue plate snap in the belt lock with a clearly audible “click”. (Picture 15) Pull the shoulder belt in arrow direction to tighten the lap belt. Check to make sure the tongue plate is locked by pulling on the belt .
Step 5. Place the diagonal belt in the diagonal belt guide at the back of the seat (Picture 16)
Step 6. Tighten the vehicle’s own 3-pointseatbelt by pulling hard on the positions . (Picture 16)
Step 7. Make sure that the belt is not twisted and strongly tightened. Make sure the seat is fixed firmly on the car seat.
Step 8. Grip the both straps motionless just above the buckle with the metal bracket . Picture 17
Step 9. Place the child in the seat. Check the height of the shoulder belts. Make sure the straps are not twisted or hanging somewhere. Fasten the seat belts on the child, making sure that they are well placed and pull the strap in the center of the seat to tighten.

www.lorelli.eu find us on
Didis Ltd. Bulgaria, Shumen, 6 Trakia-iztok Street
Phone: +359 54 850 830
e-mails:home.market@didis-ltd.com;
export@didis-ltd.com

Documents / Resources

| Lorelli RIMINI DI MARE Car Seat [pdf] Instruction Manual
RIMINI DI MARE Car Seat, RIMINI DI MARE, Car Seat, Seat
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>