FERM CDM1142P Cordless Impact Drill Instruction Manual

CDM1142P

Original instructions

WWW.FERM.COM

Cordless Li-Ion Impact driver 20V
CDM1142P

Thank you for buying this Ferm product. By doing so you now have an excellent product, delivered by one of Europe’s leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.

1. SAFETY INSTRUCTIONS

Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Save the safety warnings and the instructions for future reference.

The following symbols are used in the user manual or on the product:

 Read the user manual.

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Risk of electric shock

Variable electronic speed

Rotation, left/right

Do not use in rain

Indoor use only

Class II machine – Double insulation – You don’t need any earthed plug.

Max temperature 40°C

Do not throw the battery into fire

Do not throw the battery into water

Do not dispose of the product in unsuitable containers.

Separate collection for Li-ion battery.

Time-lag miniature fuse-link

The product is in accordance with the applicable safety standards in the European directives.

Additional safety warnings for drills and screw drivers

Drill safety warnings
a) Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
b) Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
c) Brace the tool properly before use. This tool produces a high output torque and without properly bracing the tool during operation, loss of control may occur resulting in personal injury.

Safety instructions when using long drill bits
a) Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
b) Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
c) Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

Safety warnings for battery

a) Do not open the battery. Danger of shortcircuiting.
b) Protect the battery against heat, e. g., against continuous intense sunlight, fire, water, and moisture. Danger of explosion.
c) In case of damage and improper use of the battery, vapours may be emitted. Ventilate the area and seek medical help in case of complaints. The vapours can irritate the respiratory system.
d) Use the battery only in conjunction with your Ferm Industrial product. This measure alone protects the battery against dangerous overload.
e) The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit can occur and the battery can burn, smoke, explode or overheat.

Safety warnings for charger

Intended use
Charge only CDA1132P and CDA1133P type rechargeable Battery packs with the charger.

Only use the following batteries of the Ferm Industrial FI20V battery platform. Using any other batteries could cause serious injury or damage the tool.
CDA1132P     20V, 2Ah Lithium-Ion
CDA1133P     20V, 4Ah Lithium-Ion

The following charger of the can be used to charge these batteries.
CDA1131P     Quick charger

The batteries of the Ferm Industrial FI20V battery platform are interchangeable with all the Ferm Industrial FI20V battery platform tools.

Residual risks

Even when the power tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the power tool’s construction and design:

a) Health defects resulting from vibration emission if the power tool is being used over longer period of time or not adequately managed and properly maintained.
b) Injuries and damage to property to due to broken accessories that are suddenly dashed.

Warning! This power tool produces an electromagnetic field during operation. This field may under some circumstances interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this power tool.

Power cord replacement
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

2. MACHINE INFORMATION

Intended use
The impact driver is intended for driving in and loosening screws.

Technical specifications

Vibration level
The vibration emission level stated in this instruction manual has been measured in accordance with a standardized test given in EN 62841; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned.

• Using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level.
• The times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level.

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns.

Description

The numbers in the text refer to the diagrams on pages 2- 3

Fig. A

1. Machine
2. Battery
3. Battery unlock button
4. Battery charge indication
5. Charger
6. Charger LED indicators
7. 1/4” (6.35 mm) hex chuck
8. Chuck collar
9. Work light
10. Direction switch
11. On / off switch
12. Belt hook

3. OPERATING

The battery must be charged before first use.

Removing the battery from the machine
Fig. B

• Hold the machine (1) firmly with one hand
• Push down the battery unlock button (3) located on the rear side of the battery (2) with the other hand.
• Keep pushing this button (3) down and slide the battery backwards out of the machine, like shown in Fig. B.

Inserting the battery into the machine
Fig. B
Ensure that the exterior of the battery is clean and dry before connecting to the charger or machine.

• Hold the machine (1) firmly with one hand
• Insert the battery (2) into the base of the machine as shown in Fig. B.
• Push the battery further forward until it clicks into place.

Checking the battery charging status
Fig. C
The included battery is delivered in partly charged condition.

• To check the battery charge status, push the button (4) on battery shortly.
• The battery has 3 lights indicating the charge level, the more lights that burn, the more charge the battery has left.

Charging the battery (with the charger)
Fig. C

• Take the battery (2) from the machine
• Turn the battery (2) to upside down position and slide it onto the charger (5) as shown in Fig. C.
• Push the battery until it is fully pushed into the slot.
• Plug the charger plug into an electrical outlet and wait for a while. The LED indicators on the charger (6) will lighten up and show the charger status.

LED indicators (6)
Fig.C
The charger has 2 LED indicators (6) which indicate the status of the charging process:

-No battery is inserted or,
-Battery inserted but charging has finished more then 2 hours ago
Blinking| Blinking| Defective battery
On| Blinking| Battery charging in progress
On| On| Battery charging finished, battery fully charged
Blinking| Off| Battery is too hot, charging progress is on hold. Charging will start automatically after the battery has cooled down.

• Fully charging the battery may take up to 60 minutes.
• After the battery is fully charged remove the charger plug from the outlet and remove the battery from the charger.
• The battery can be stored or directly installed on the machine.

Lithium-Ion cells can be stored for a long period without losing much of their charge. When the machine is not being used over a longer period of time it is best to store the battery in charged condition.

Quick-Release Chuck
Use only 1/4″ (6.35 mm) hex impact accessories. Non-impact accessories may break and cause a hazardous condition. Inspect accessory prior to use to ensure that it contains no cracks.

Place the direction switch (10) in the lock-off (centre) position or remove battery pack before changing accessories. To install an accessory, fully insert the accessory. The accessory is locked into place. To remove an accessory, pull the chuck collar (8) away from the front of the tool. Remove the accessory.

Adjusting the direction of rotation
Fig. A

• Set the direction switch (10) to position “ ” in order to drive screws or to use it for drilling.
• Set the direction switch (10) to position “ ” in order to remove screws

Switching the machine on and off
Fig. A
The on/off switch (11) is used for activating the machine and adjusting rotation speed.

• Pressing the on/off switch (11) will activate the machine, the further the switch is being pushed, the faster the drill will turn.
• Releasing the on/off switch (11) will stop the machine.
• Move the direction reversing switch (10) to the middle position to lock the movement of the on/ off switch. It cannot be activated in this position.

Only lay down the machine when it has stopped running completely. Do not place it on a dusty surface as particles of dust could get into the mechanism.

Work light (9)
Fig. A
The machine is equipped with a work light to illuminate the work location.

• It automatically switches on when the on/off switch is being pressed.
• It automatically switches off when the on/off switch is released again.

Belt hook (12)
Fig. A
The machine is equipped with a belt hook for hanging the machine to your belt during use.

Always switch the direction switch (10) to middle position to avoid accidental startup of the machine.

• When delivered, the belt hook (12) is assembled to the left side of the machine.
• It can easily be removed by removing the screw on the hook and taking it off.
• It can be assembled on the right side of the machine when this is preferred.

4. MAINTENANCE

Before cleaning and maintenance, always switch off the machine and remove the battery pack from the machine.

Clean the machine casings regularly with a soft cloth, preferably after each use. Make sure that the ventilation openings are free of dust and dirt. Remove very persistent dirt using a soft cloth moistened with soapsuds. Do not use any solvents such as gasoline, alcohol, ammonia, etc. Chemicals such as these will damage the synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

WARRANTY

The warranty conditions can be found on the separately enclosed warranty card.

The product and the user manual are subject to change. Specifications can be changed without further notice.

Spare parts list

CDM1142P

Exploded view

DECLARATION OF CONFORMITY

CDM1142P – CORDLESS LI-ION IMPACT DRIVER

We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:

EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 62233
EN 62841-1, EN 62841-2-2, EN 60335-1, EN 60335-2-29,
2006/42/EC, 2011/65/EU, 2012/19/EU, 2014/35/EU, 2014/30/EU

Zwolle, 01-05-2021          H.G.F Rosberg

CEO FERM

FERM – Lingenstraat 6 – 8028 PM – Zwolle – The Netherlands

WWW.FERM.COM

2105-19
©2021 FERM

Documents / Resources

| FERM CDM1142P Cordless Impact Drill [pdf] Instruction Manual
CDM1142P Cordless Impact Drill, CDM1142P, Cordless Impact Drill, Impact Drill, Drill
---|---

References

• FERM Power Tools - Power to create

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>