FERM CDA1169 20V Charger Adapter User Manual

CDA1169 20V Charger Adapter
User Manual 20V
CHARGER ADAPTER
CDA1169

THE EXCHANGEABLE BATTERY PLATFORM
****WWW.FERM.COM

CDA1169 20V Charger Adapter

Charger adapter 20V
CDA1169

SAFETY INSTRUCTIONS

Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Save the safety warnings and the instructions for future reference.
The following symbols are used in the user manual or on the product:

| Read the user manual.
---|---
| Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the  instructions in this manual.
| Switched-mode power supply.
| In case of failure, the transformer is not dangerous.
| Class II machine – Double insulation – You don’t need any earthed plug.
| Do not dispose of the product in unsuitable containers.
****| The product is in accordance with the applicable safety standards in the European directives.

GENERAL POWER TOOL SAFETY WARNINGS
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodifi ed plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
SAFETY WARNINGS FOR CHARGER
Intended use
Charge only CDA1167 and CDA1168 type rechargeable Battery packs with the charger. Other types of batteries may burst causing personal injury and damage.
a) This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
b) Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
c) Do not recharging nonrechargeable batteries!
d) During charging, batteries must be placed in the well ventilated area!
ELECTRICAL SAFETY
**** Always check that the voltage of the power supply corresponds to the voltage on the rating plate.

• Do not use the machine if the mains cable or the mains plug is damaged.
• Only use extension cables that are suitable for the power rating of the machine with a minimum thickness of 1.5 mm2.
• If you use a extension cable reel, always fully unroll the cable.

PRODUCT INFORMATION

Intended use
Only use the following batteries of the FX-POWER 20V battery platform. Using any other batteries could cause serious injury or damage the charger.
CDA1167 20V, 2Ah Lithium-Ion (5pcs 2Ah battery cells in series)
CDA1168 20V, 4Ah Lithium-Ion (5pcs 2Ah battery cells in series, two series in parallel)
The batteries of the FX-POWER 20V battery platform are interchangeable with all the FERM FX-POWER 20V battery platform tools.
TECHNICAL SPECIFICATIONS

**DESCRIPTION

**

The numbers in the text refer to the diagrams on pages 2.

1. Battery unlock button
2. Battery LED indicators button
3. Battery LED indicators
4. Battery (not included)
5. Charger
6. Charger LED indicator

OPERATION

Before any work on the power tool, remove the battery.
The battery must be charged before first use.
Inserting the battery into the machine (Fig. B)
Ensure that the exterior of the battery is clean and dry before connecting to the charger or machine.

1. Insert the battery (4) into the base of the machine as shown in Fig. B.
2. Push the battery further forward until it clicks into place.

Removing the battery from the machine (Fig. B)

1. Push the battery unlock button (1)
2. Pull the battery out of the machine like shown in Fig. B.

Checking the battery charging status (Fig. A)

• To check the battery charge status, push the button (2) on battery shortly.
• The battery has 3 lights indicating the charge level, the more lights that burn, the more charge the battery has left.
• When the lights are not burning it means the battery is empty and must be charged immediately.

Charging the battery with the charger (Fig. A)

1. Take the battery (4) from the machine.
2. Plug the output of the charger into the round socket of the battery.
3. Plug the charger plug into an electrical outlet and wait for a while. The LED indicators on the battery (6) will lighten up and show the charger status.

LED indicator (6) (Fig. A)
The battery has 1 LED indicator (6) which indicates the status of the charging process:

• Fully charging the 2Ah battery may take up to 90 minutes.
• Fully charging the 4Ah battery may take up to 120 minutes.

After the battery is fully charged remove the charger plug from the outlet and remove the battery from the charger.
  When the machine is not being used over a longer period of time it is best to store the battery in charged condition.

MAINTENANCE

Before cleaning and maintenance, always switch off the machine and remove the battery pack from the machine.
Clean the battery casings regularly with a soft cloth, preferably after each use. Make sure that the ventilation openings are free of dust and dirt. Remove very persistent dirt  using a soft cloth moistened with soapsuds. Do not use any solvents such as gasoline, alcohol, ammonia, etc. Chemicals such as these will damage the synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/ EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

WARRANTY

FX-POWER products are developed to the highest quality standards and are guaranteed free of defects in both materials and workmanship for the period lawfully stipulated starting from the date of original purchase. Should the product develop any failure during this period due to defective material and/or workmanship then contact your FX-POWER dealer directly.
The following circumstances are excluded from this guarantee:

• Repairs and or alterations have been made or attempted to the machine by unauthorized service centers.
• Normal wear and tear.
• The tool has been abused, misused or improperly maintained.
• Non-original spare parts have been used

This constitutes the sole warranty made by company either expressed or implied. There are no other warranties expressed or implied which extend beyond the face hereof, herein, including the implied warranties of merchantability and fitness for a particular purpose. In no event shall FX- POWER be liable for any incidental or consequential damages. The dealers remedies shall be limited to repair or replacement of nonconforming units or parts.
The product and the user manual are subject to change. Specifications can be changed without further notice.

DECLARATION OF CONFORMITY

CDA1169 – CHARGER ADAPTER 20V
**** We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:

EN 55014-1, EN 55014-2, EN 60745-1, EN 60745-2-22, EN 60825-1,
EN 61000-3-2, EN 61000-3-3
2014/30/EU, 2006/42/EC, 2012/19/EU, 2011/65/EU
Zwolle, 01-03-2019

H.G.F. Rosberg
CEO Ferm
Ferm • Lingenstraat 6 • 8028 PM
Zwolle The Netherlands
WWW.FERM.COM
1903-22
©2019 FERM

References

• FERM Power Tools - Power to create

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>