FERM CTM1012 Multifunction tool Instruction Manual
- June 9, 2024
- FERM
Table of Contents
FERM CTM1012 Multifunction tool
Thank you for buying this Ferm product.
By doing so you now have an excellent product, delivered by one of Europe’s
leading suppliers. All products delivered to you by Ferm are manufactured
according to the highest standards of performance and safety. As part of our
philosophy we also provide an excellent customer service, backed by our
comprehensive warranty. We hope you will enjoy using this product for many
years to come.
Read the operating instructions carefully before using this device.
Familiarise yourself with its functions and basic operation. Service the
device as per the instructions to ensure that it always functions properly.
The operating instructions and the accompanying documentation must be kept in
the vicinity of the device.
Machine data
Technical specifications
- Voltage 230 V
- Frequency 50 Hz
- Power consumption 160 W
- No load speed 15.000–35.000/min
- Capacity of spring chuck 3.2 + 2.4 mm
- Weight 0.6 kg
- Lpa (Sound pressure level) 70+3 dB(A)
- Lwa (Sound power level) 83+3 dB(A)
- Vibration 1.7+1.5 m/s2
Vibration level
The vibration emission level stated in this instruction manual has been
measured in accordance with a standardized test given in EN 60745; it may be
used to compare one tool with another and as a preliminary assessment of
exposure to vibration when using the tool for the applications mentioned.
- using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level.
- the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level.
Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns.
Package contents
- 1 Combitool
- 1 Spring chuck spanner
- 40 Accessories
- 1 Case
- 1 Instructions for use
- 1 Safety section
- 1 Guarantee card
Check first whether or not the delivery has been damaged by transport and/or whether all the parts are present.
Features
- Collet chuck
- Ring
- Spindle lock
- Speed adjusting wheel
- Clip
Safety instructions
Explanation of symbols
- Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.
- Indicates the presence of an electrical voltage.
- Variable speed control.
- Wear ear and eye protection.
- Wear a dust mask.
Special safety instructions
- Always keep the cord away from the moving parts of the machine.
- In the case of locking, switch the machine off immediately and remove the plug from the mains.
- Compare the maximum number of revolutions allowed of the accessories with the number of revolutions of the machine.
- When you put the machine away the engine must be switched off and moving parts must have reached a standstill.
- Never attach an assembly spanner to your machine with a piece of string or anything similar.
- Never use the axle locking button if the machine is operating.
- Make sure that the spring chuck diameter is the same as the axle diameter of the accessory.
- Use a clamping device for securing the work piece.
- Keep your hands away from the work piece.
Electrical safety
When using electric machines always observe the safety regulations applicable
in your country to reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and also the enclosed safety
instructions.
- Always check that the power supply corresponds to the voltage on the rating plate.
- Your machine is double insulated, therefore no earth wire is required.
Replacing cables or plugs
If the mains cable becomes damaged, it must be replaced with a special mains
cable available from the manufacturer or the manufacturer’s customer service.
Dispose of old cables or plugs immediately after replacing them with new ones.
It is dangerous to connect the plug of a loose cable to a socket.
Using extension cables
Only use an approved extension cable suitable for the power input of the
machine. The minimum conductor size is 1.5 mm2. When using a cable reel always
unwind the reel completely.
Assembly of accessories
- Before assembly always remove the plug from the mains.
- Warning! Change accessories by inserting an accessory into the collet (or chuck) as far possible to minimize run out and unbalance.
Assembly of accessories
Press down the axle locking button (2) and hold it down. Using the spring
chuck spanner you can undo the spring chuck (1). Put the accessory in its
place. Hold down the axle locking button when you fasten the spring chuck with
the spring chuck spanner.
Operation
Switch on the machine by engaging the on/out switch (A) By adjusting the
adjusting wheel (B) you can regulate the speed of the Combitool. Do not put
the machine down when the motor is still running. Do not place the machine on
a dusty surface. Dust particles may enter the mechanism.
Too high a load at a low speed of the Combitool can burn out the engine.
Holding and guiding the tool
- For precision work (engraving): pencil grip (A)
- For rough work (grinding): paring knife hand grip (B)
- When you need to keep the tool parallel to the work surface (e.g. using a cut-off wheel): 2 hand golf grip (C)
Accessories for the Combitool
Ferm does not deliver spare accessories for the Combitool. The Combitool is designed to use the standard accessories of Dremel, Black & Decker, Bosch or Proxxon. Always check that the maximum rpm of the accessory is suitable for the maximum speed of the Combitool.
Grinding stones
When using a grinding stone the first time, use the dressing stone to balance
it. The dressing stone can also be used for cleaning the surface or to give
the grinding stone a special shape.
Felt wheels and tip
The felt wheels or tip should be screwed on the mandrel.
Sanding bands and disc
Stainless steel brushes and bristle brush
High speed cutter, Diamond wheel point and Drill
Abrasive disc
Maintenance
Make sure that the machine is not live when carrying out maintenance work on
the motor.
This machine has been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation depends upon proper
machine care and regular cleaning.
Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the
engine. Regularly clean the machine housing with a soft cloth, preferably
after each use. Keep the ventilation slots free from dust and dirt. If the
dirt does
not come off use a soft cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These solvents may damage the
plastic parts. Please clean the tool immediately after use.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please contact the service
address on the warranty card. In the back of this manual you find an exploded
view showing the parts that can be ordered.
Environment
To prevent damage during transport, the appliance is delivered in a solid
packaging which consists largely of reusable material. Therefore please make
use of options for recycling the packaging.
Damaged and/or disposed of electrical or electronic devices must be dropped
off at recycling stations intended for that purpose.
Only for EC countries
Do not dispose of power tools into domestic waste. According to the European
Guideline 2012/19/EU for Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are no longer usable must
be collected separately and disposed of in an environmentally friendly way.
Warranty
Read the warranty conditions on the separately supplied warranty card.
The product and the user manual are subject to change. Specifications can be
changed without further notice.
Exploded view
| Position | Description | No. |
|---|---|---|
| 406894 | Switch | 1 |
| 406895 | Carbon brush (set) | 2 |
| 406896 | Collet nut | 3 |
| 406709 | Ring | 4 |
| 406683 | Collet chuck 3.2 MM | 5 |
| 406684 | Collet chuck 2.4 MM | 5 |
| 406897 | Spindle lock | 6 |
| 406708 | Flexible shaft | – |
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in conformity
with directive 2011/65/EU of the European parliament and of the council of 8
June on the restriction of the use of certain hazardous substances in
electrical and electronic equipment is in conformity and accordance with the
following standards and regulations:
WWW.FERM.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>