StarTech Com SDOCK2U33 USB 3.0 to Dual 2.5-3.5 Inch SATA HDD Dock with UASP User Manual
- June 9, 2024
- StarTech com
Table of Contents
SDOCK2U33 USB 3.0 to Dual 2.5-3.5 Inch SATA HDD Dock with UASP
User Manual
USB 3.0 to Dual 2.5/3.5in SATA HDD Dock
with UASP
SDOCK2U33
SDOCK2U33 USB 3.0 to Dual 2.5-3.5 Inch SATA HDD Dock with UASP
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way
to StarTech.com. Where they occur these references are
for illustrative purposes only and do not represent an endorsement of a
product or service by StarTech.com, or an endorsement
of the product(s) to which this manual applies by the third-party company in
question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that
all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Product Overview
Front View
Rear View
Introduction
Packaging Contents
- 1 x USB 3.0 to dual 2.5/3.5 in. SATA hard drive docking station
- 1 x USB 3.0 cable
- 1 x universal power adapter (NA/JP, EU, UK, ANZ)
- 1 x instruction manual
System Requirements
- Computer system with available USB 3.0 (5 Grit/s) port or USB 2.0 (480Mbps) port
- Up to two 2.5” or 3.5” SATA Hard Drives (HDD) or Solid State Drives (SSD)
Installation
WARNING! Hard drives and docking stations require careful handling. If you are not careful with your hard disk, lost data may result. Always handle your hard drive and docking station with caution. Be sure that you are properly grounded by wearing an anti-static strap when handling computer components or discharge yourself of any static electricity build-up by touching a large grounded metal surface (such as the computer case) for several seconds.
Docking Station Installation
- Connect the Dock to an available power outlet, using the provided power adapter.
- Connect the Dock to your computer system, using the provided USB 3.0 cable.
Drive Installation
- Carefully align and insert the 2.5” or 3.5” SATA drive(s) you wish to dock in the desired hard drive slot on the docking station, such that the SATA power and data connectors on the drive are properly aligned with the corresponding connectors inside the hard drive slot.
- Press the power button(s) that correspond with the hard drive(s) you wish to access to turn the docking station on.
- Once the drives have been installed and the docking station has been powered on, the computer Operating System will automatically recognize the drive(s) and it will be accessible as though it were installed in the system internally.
Note: If your computer fails to automatically recognize your drive it is likely your drive has not been initialized or formatted correctly. (See Drive Initialization in Software operation for further instructions.)
Drive Removal
WARNING! Ensure your hard drive(s) has been disconnected from your
computer operating system prior to attempting drive removal. Failure to
properly disconnect your drive may result in lost data or drive damage. (See
Disconnecting the Hard Drive in Docking Station Operation for further
instructions.)
- Press the power button that corresponds with the drive you wish to remove, in order to turn off the drive.
- Press the eject button that corresponds with the drive you wish to remove.
- Carefully grasp the ejected drive and lift it upwards until the bottom of the drive has completely risen above the hard drive slot.
- Safely and carefully store your drive in a secure location. (See your hard drive manual for proper storage instructions.)
Docking Station Operation
Drive Initialization
Prior to using your installed drive, it will need to be initialized and
formatted to the operating system requirements in order for your computer
system to recognize it.
-
From the main Windows desktop, right-click on “My Computer” (“Computer” in Vista/7 / 8/ 8.1), then select Manage. In the new Computer Management window, select Disk Management from the left window panel.
-
A dialog window will automatically appear, asking you to initialize the drive. Depending on the version of Windows, it will give you the option of either creating an “MBR” or “GPT” disk.
Note: GPT (GUID partition) is required for drives larger that 2TB but is not compatible with some older operating systems, while MBR is supported by newer and older operating systems. -
Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard drive capacity to confirm it’s the correct hard drive) and then right-click in the section that says “Unallocated” and select “New Partition”.
-
Follow the on screen prompts to initialize the drive in the format of your choice.
LED Indicators
The docking station offers a power LED indicator (blue) and an activity LED
indicator (red) for each drive. When the drive is powered on, the Blue LED
Power indicator will illuminate. While the hard drive is being accessed, the
Red LED will flash. Do not remove your drive from the docking station while
the Red LED is flashing, as it could
damage to your drive, resulting in data loss.
Disconnecting the Hard Drive
Windows
- Select the “Safely remove Hardware and Eject Media” icon, located in the task bar.
- Select the storage device from the list that appears.
- Wait for the message indicating that it is now safe to remove the device.
Note: Removing the connected drive prior to receiving notification that it is safe to do so, could result in losing or corrupting data stored on the drive. Once the Safe to Remove Hardware message appears, please remove the drive from the docking station. (See Drive Removal.)
Mac OS X
To safely disconnect the attached drive from the host computer, close any windows listing the contents of the removable drive. Once all windows are closed, click on the
USB storage icon on the desktop, and drag it to the Trash Can icon on the desktop.
Allow 5 seconds before physically removing the drive from the docking station.
Specifications
| Host Interface | USB 3.0 |
|---|---|
| External Connectors | 1 x USB 3.0 B female |
| Internal Connectors | 2 x SATA DATA (7 pin) + Power (15 pin) reciprocal |
| Maximum Data Transfer Rate | USB 3.0: 5 Grit/s |
Technical Support
StarTech.com’s lifetime technical support is
an integral part of our commitment to provide industry-leading solutions. If
you ever need help with your product, visit
www.startech.com/support and access our
comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit
www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against
defects in materials and workmanship for the periods noted, following the
initial date of purchase. During this period, the products may be returned
for repair, or replacement with equivalent products at our discretion. The
warranty covers parts and labor costs only. StarTech.com does not warrant its
products from defects or damages arising from misuse, abuse, alteration, or
normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd.
and StarTech.com USA LLP (or their officers, directors,
employees or agents) for any damages (whether direct or indirect, special,
punitive, incidental, consequential, or otherwise), loss of profits, loss of
business, or any pecuniary loss, arising out of or related to the use of the
product exceed the actual price paid for the product. Some states do not allow
the exclusion or limitation of incidental or consequential damages. If such
laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-find made easy. At StarTech.com, that isn’t a
slogan. It’s a promise.
StarTech.com is your one-stop source for every
connectivity part you need. From the latest technology to legacy products —
and all the parts that bridge the old and new — we can help you find the
parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they
need to go. Just talk to one of our tech advisors or visit our website. You’ll
be connected to the products you need in no time.
Visit www.startech.com for complete information on
all StarTech.com products and to access exclusive
resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of
connectivity and technology parts. StarTech.com was
founded in 1985 and has operations in the United States, Canada, the United
Kingdom and Taiwan servicing a worldwide market.
References
- StarTech.com | IT Pro's Trusted Source for Connectivity Accessories | Europe
- Drivers & Downloads | StarTech.com Support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>