Char-Broil 468972023 Professional Power Edition 2 Burner Instruction Manual

June 9, 2024
Char-Broil

Char-Broil-LOGO

Char-Broil 468972023 Professional Power Edition 2 Burner

Char-Broil-468972023-Professional-Power-Edition-2-Burner-
PRODUCT

Important Instruction

INSTALLER/ASSEMBLER:

  • Leave this manual with consumer.

CONSUMER:

  • Keep this manual for future reference.

Questions:

  • If you have questions during assembly or use of this appliance contact your local dealer.

DANGER If you smell gas:

  1. Shut off gas to the appliance.
  2. Extinguish any open flames.
  3. Open lid.
  4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.

WARNING

  1. Do not store or use petrol or other flammable liquids in the vicinity of this or any other appliance.
  2. A gas cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

CAUTION

  • Read and follow all safety statements, assembly instructions and use and care directions before attempting to assemble and cook.
  • Some parts may contain sharp edges. Wearing protective gloves is recommended.

Grease Fires

  • Putting out grease fires by closing the lid is not possible. Barbecues are well ventilated for safety reasons.
  • Do not use water on a grease fire, Personal injury may result. If a persistent grease fire develops, turn knobs and gas cylinder off.
  • If appliance has not been regularly cleaned, a grease fire can occur that may damage the product. Pay close attention while preheating or burning off food residue to insure that a grease fire does not develop. Follow instructions on general appliance cleaning and cleaning the burner assembly to prevent grease fires. The best way to prevent grease fires is regular cleaning of the appliance.
  • Do not leave barbecue unattended while preheating or burning off food residue on HI. If barbecue has not been regularly cleaned, a grease fire can occur that may damage the product.

WARNING

  • For Safe Use of Your Appliance and to Avoid

Serious Injury:

USE OUTDOORS ONLY. NEVER USE INDOORS.

  • Read the instructions before using the appliance.
  • Always follow these instructions.
  • Do not move the appliance during use.
  • Accessible parts may be very hot. Keep young children away. Do not let children operate or play near appliance.
  • Turn off the gas supply at the cylinder after use.
  • This appliance must be kept away from flammable materials during use.
  • Do not block holes in sides or back of appliance.
  • Check burner flames regularly.
  • Do not block venturi openings on burner.
  • Use appliance only in well-ventilated space. NEVER use in enclosed space such as carport, garage, porch, covered patio, or under an overhead structure of any kind.
  • Do not use charcoal or ceramic briquets in a gas appliance.
  • DO NOT cover grates with aluminum foil or any other material. This will block burner ventilation and create a potentially dangerous condition resulting in property damage and/or personal injury.

Use appliance at least 1m from any wall or surface.

  • Maintain 3m clearance to objects that can catch fire or sources of ignition such as pilot lights on water heaters, live electrical appliances, etc.
  • NEVER attempt to light burner with lid closed. A buildup of non-ignited gas inside a closed appliance is hazardous.
  • Always turn off gas at cylinder and disconnect regulator before moving gas cylinder from specified operating position.
  • Never operate appliance with gas cylinder out of correct position specified.
  • Do not modify the appliance. Any modifications is strictly prohibited. Sealed parts are not to be manipulated by the user. Do not disassemble injectors.

Safety Tips

  • Before opening gas cylinder valve, check the regulator for tightness.
  • When appliance is not in use, turn off all control knobs and gas.
  • Use long-handled barbecue utensils and oven mitts to avoid burns and splatters. Use protective gloves when handling hot components.
  • Maximum load for hot plate, if equipped, and side shelf is 4.5 Kg. Cooking vessel minimum dia 200mm and maximum dia. 260 mm. NOTE: Your barbecue may NOT be equipped with a Hot plate!
  • The grease cup (if equipped) must be inserted into appliance and emptied after each use. Do not remove grease cup until appliance has completely cooled.
  • Be very careful when you open the lid, since hot steam may escape.
  • Be very careful when children, the elderly, or pets are nearby.
  • If you notice grease or other hot material dripping from appliance onto valve, hose or regulator, turn off gas supply at once. Determine the cause, correct it, then clean and inspect valve, hose, and regulator before continuing. Perform a leak test.
  • Do not store objects or materials inside the appliance cart enclosure that would block the flow of combustion air to the underside of either the control panel or the firebox bowl.
  • DO NOT disconnect or change gas container within 3m of an open flame or other ignition source.

Cylinder Placement

  • Cylinders placed in the appliance shall have a maximum diameter of 340mm and maximum height, including regulator, of 580mm. Larger cylinders are to be placed under side shelf or behind the barbecue only. Cylinders placed on the ground shall not be placed under the hot plate.

Regulator Requirements

  • A regulator must be used with this appliance. Use only gas regulator supplied with your barbeque. If a regulator is not supplied then use only regulator certified according to EN16129 (Flow rate max. 1.5 kg/h) and approved for your country and gas specified in Technical Data.

Hose Requirements

  • Use only approved hose which is certified to appropriate EN standard and does not exceed 1.5m length. For Finland, the hose length shall not exceed 1.2m.
  • Before each use, check to see if hoses are cut or worn. Make sure hose is not kinked. Replace damaged hoses before using appliance. Replace hose as required by national requirements.
Ignitor Lighting
  • Do not lean over barbecue while lighting.
  1. Turn gas burner control valves to (off).
  2. Open lid during lighting or re-lighting.
  3. Turn ON gas at LP cylinder.
  4. To ignite, push and turn burner knob to HIGH. Immediately, push and hold ELECTRONIC IGNITOR button until the burner lights.
  5. If ignition does NOT occur in 5 seconds, turn the burner controls off , wait 5 minutes and repeat the lighting procedure.
  6. Repeat steps 4 and 5 to light other main burners.

WARNING

  • Turn controls and gas cylinder off when not in use.
  • Make sure that when connected hose does not touch any warm surfaces.

CAUTION

If ignition does NOT occur in 5 seconds, turn the burner controls off, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with the valve open, gas will continue to flow out of the burner and could accidently ignite with risk of injury.

Match-Lighting
  • Do not lean over barbecue while lighting.
  1. Turn gas burner control valves to (off).
  2. Open lid during lighting or re-lighting.
  3. Turn ON gas at LP cylinder.
  4. Place match into match holder (hanging from side panel of barbecue). Light match; then light burner by placing match through the match light hole on side of barbecue. Immediately push in and turn burner knob to the HIGH position. Be sure burner lights and stays lit.
  5. Light adjacent burners in sequence by pushing knobs in and turning to the HIGH position.
Sear Burner Ignitor Lighting

Do not lean over barbecue while lighting.

  1. Turn gas burner control valves to OFF.
  2. Open lid during lighting or re-lighting.
  3. Turn ON gas at LP cylinder.
  4. Turn Sear Burner knob to the HIGH position, push and hold ELECTRONIC IGNITOR button.
  5. If Sear Burner does NOT light within 5 seconds, turn knob to OFF, wait 5 minutes, then repeat lighting procedure.
Sear Burner Match Lighting

Do not lean over barbecue while lighting.

  1. Turn gas burner control valves to OFF.
  2. Open lid during lighting or re-lighting.
  3. Turn ON gas at LP cylinder.
  4. Place lit match near burner. Immediately turn Sear Burner knob to the HIGH position. Be sure the burner lights and stays lit.

CAUTION

SPIDER ALERT! SPIDER AND WEBS INSIDE BURNER

If your barbeque is getting hard to light or the flame is weak, check and clean the venturis and burners.
Spiders or small insects are known to create “flashback” problems by building nests and laying eggs in the barbeque’s venturi or burner obstructing the flow of gas. The backed-up gas can ignite behind the control panel. This flashback can damage your barbeque and cause Injury. To prevent flashbacks and ensure good performance, the bumer and venturi tube assembly should be removed and deaned whenever the barbeque has been idle for an extended period of time.

Leak Testing Valves, Hose and Regulator
  • Leak test before first use, at least once a year, and every time the cylinder is changed or disconnected.
  1. Turn all appliance control knobs to .
  2. Be sure regulator is tightly connected to gas cylinder.
  3. Turn on Gas. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding.
  4. Brush soapy solution (mixture of half soap and half water) onto hose connections.
  5. If growing bubbles appear, there is a leak. Turn off gas at cylinder immediately and check tightness of connections. If leak cannot be stopped do not try to repair. Call for replacement parts.
  6. Always turn off gas at cylinder after performing leak test.
IF THE APPLIANCE FAILS TO LIGHT
  • Make sure the gas is turned on at the cylinder.
  • Make sure there is gas in the cylinder.
  • Does the ignitor make a sparking noise?
  • If yes check for a spark at the burner.
  • If no spark check for damaged or loose wires.
  • If wires are OK check for cracked or broken electrode, replace if needed.
  • If wire or electrodes are covered by cooking residue, clean electrode tip with alcohol wipe if needed.
  • If needed replace wires.
  • If no sound check battery.
  • Make sure the battery is installed correctly.
  • Check for loose wire connection at the module and switch.
  • If the ignitor continues to not work then use match.
Cleaning the Burner Assembly

Follow these instructions to clean and/or replace parts of the burner assembly or if you have trouble igniting the barbecue.

  1. Turn the gas off at the control knobs and LP cylinder.

  2.  Remove cooking grates and heat tents.

  3. Remove carryover tubes and hardware securing burners.

  4. Detach the electrode from the burner.
    NOTE: Removal/Detachment method will depend on the burner configuration. See different configurations in the illustrations below.

  5. Carefully lift each burner up and away from valve openings.
    We suggest three ways to clean the burner tubes. Use the one easiest for you.
    A. Bend a stiff wire (a lightweight coat hanger works well) into a small hook. Run the hook through each burner tube several times.
    B. Use a narrow bottle brush with a flexible handle (do not use a brass wire brush). Run the brush through each burner tube several times.
    C. Wear eye protection: Use an air hose to force air into the burner tube and out the burner ports. Check each port to make sure air comes out of each hole.

  6. Wire brush the entire outer surface of the burner to remove food residue and dirt.

  7. Clean any blocked ports with a stiff wire such as an open paper clip.

  8. Check the burner for damage due to normal wear and corrosion, some holes may become enlarged. If any large cracks or holes are found, replace the burner.
    VERY IMPORTANT: Burner tubes must reengage valve openings. See illustrations at right Correct burner-valve engagement

  9. Attach the electrode to the burner.

  10. Carefully replace burners.

  11. Attach burners to brackets on the firebox.

  12. Reposition carryover tubes and attach them to burners. Replace heat tents and cooking grates.

  13. Before cooking again on a barbecue, perform a “Leak Test” and “Burner Flame Check”.

Storing Your Appliance
  • Clean cooking grates.
  • Store in dry location.
  • When gas cylinder is connected to appliance, store outdoors in a well-ventilated space and out of reach of children.
  • Cover appliance if stored outdoors.
  • Store appliance indoors ONLY if gas cylinder is turned off and disconnected, removed from appliance and stored outdoors. When removing appliance from storage check for burner obstructions.

General Appliance Cleaning

  • Periodic cleaning of this grill is necessary, as grill fires can occur when grease and food debris collect in the bottom of the grill. After each use, remove any remaining food particles from the cooking grate and inside of the grill using a Char-Broil Cool-Clean Brush. Afterwards you could spray Char-Broil Grate Cleaner generously onto the grate, allow it work for 10 minutes and wipe off with a wet cloth or brush. Perform grill cleaning after the grill has cooled down.
  • Do not mistake brown or black accumulation of grease and smoke for paint. Interiors of gas barbecues are not painted at the factory (and should never be painted). Apply a strong solution of detergent and water or use a appliance cleaner with scrub brush on insides of appliance lid and bottom. Rinse and allow to completely air dry. Do not apply caustic appliance/oven cleaner to painted surfaces. Plastic parts: Wash with warm soapy water and wipe dry.
  • Do not use abrasive cleaners, degreasers or a concentrated appliance cleaner on plastic parts. Damage to and failure of parts can result.
  • Porcelain surfaces: Because of glass-like composition, most residue can be wiped away with baking soda/water solution, glass cleaner or Char-Broil Grate Cleaner. Use nonabrasive scouring powder for stubborn stains.
  • • Painted surfaces: Wash with mild detergent or cleaner and warm soapy water or Char-Broil Grill Cleaner. Wipe dry with a soft nonabrasive cloth.
    • Cooking surfaces: Ensure no loose bristles remain on cooking surfaces prior to grilling. While grill is hot, it is only recommended to clean cooking surfaces using the Char-Broil Hot-Clean Replacement head (on the Char-Broil Cool-Clean Premium Brush).

CLEAN Setting

  • Your grill is equipped with an innovative CLEAN setting that allows for hassle-free grill cleaning.
  • The high heat generated from the burners will turn all remaining food debris to ash. Follow these steps:
  • After you are done grilling, adjust all main burners to CLEAN setting and remain for approximately 12 – 15 minutes
  • After approximately 12 – 15 minutes, adjust all main burners to OFF setting and allow grill to cool
  • Once the grill is cool, use a Char-Broil Cool-Clean Brush to remove any remaining debris and dispose of the ash
  • To get extra-shiny results, use the Char-Broil Grate Cleaner as a last step. Spray generously onto the grate, allow it work for 10 minutes and wipe off with a wet cloth or brush.

IMPORTANT! PLEASE READ!Char-Broil-468972023-Professional-Power-Edition-2
-Burner-FIG-7 Char-
Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-8

  • A regulator must be used with this appliance. Use only the gas regulator supplied with your barbeque. If a regulator is not supplied then use only a regulator certified according to EN16129 (Flow rate max. 1.5 kg/h) and approved for your country and gas specified in Technical Data.

For Switzerland Only

  • There is a danger of fire and explosion with gas appliances which are equipped with foreign pressure regulators and are not compatible with the gas tanks and gas regulators available in Switzerland
  • Due to the different sealing systems, it is impossible to properly seal the regulator to the gas tank. Gas will escape here and can be ignited by flame or sparks. A life-threatening explosion, and/or property damage can result. Swiss and German tanks and regulators cannot be intermixed.
  • For safety reason, please check your grill regulator and gas tank connection and make sure it follows in one of the allowed cases shown in the pictures.
  • Perform a leak check each time you connect your grill to the gas tank.

TECHNICAL DATA CHAR-BROIL, LLC

Appliance Name| Gas Barbeque/Gas Grill
Total Nominal Heat Input| 9.67 kW (704 g/h)| 9.67 kW (704 g/h)
Gas Category| I3+(28-30/37)| I3B/P(30)| I3B/P(50)
Model No.|

468972023

| 468782023
Gas Type| Butane| Propane| Butane, Propane or their mixtures| Butane, Propane or their mixtures
Gas Pressure| 28-30 mbar| 37 mbar| 30 mbar| 50 mbar

Injector Size (Dia. mm)

| Barbecue: 0,86 x 2 pcs| Barbecue: 0,86 x 2 pcs| Barbecue: 0,75 x 2 pcs
Sear Burner

Injector Size (Dia. mm)

| 0,91 x 1 pcs| 0,91 x 1 pcs| 0,81 x 1 pcs
Destination Countries| GB, FR, BE, ES, IT, PT, CZ, SK,

CH, CY, GR, IE, LT, LU, LV, SI

| DK, NO, NL, SE, FI, IS, CZ,

IT, SK, BG, CY, EE, HR, HU, LT, LU, LV, MT, RO, SI, TR

| AT, DE, CH, LU, SK

Stainless steel
  • There are many different types (alloys) of materials that are regarded as stainless steel.
  • A common trait of these different types is that they may corrode (oxidize), depending on the Conditions they are subjected to.
  • This applies to your new barbecue as well.
  • To ensure your barbecue retains its looks and functionality for many years, please follow the advice below.
  1. If the barbecue has become wet or damp, make sure to wipe it dry using a cloth in order to prevent surface corrosion.
  2. Stainless steel can rust under certain conditions. This can be caused by environmental conditions Such as chlorine or salt water, or improper cleaning tools such as wire or steel wool. It can also discolor due to heat, chemicals, or grease build-up.
  3. To maintain your appliance’s high quality appearance, wash with mild detergent and warm soapy water and wipe dry with a soft cloth after each use. Baked-on grease deposits may require the use of an abrasive plastic cleaning pad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with graphics.
  4. Grease the internal parts of the barbecue and the grids with cooking oil.
  • Please note: To avoid scratching the surface and providing a basis for rust, never use steel wool or similar when cleaning stainless steel.
  • When cleaning, work in the same direction the stainless steel was brushed in – with the grain’. Cleaning with abrasives may leave scratches.
  • Storing the barbecue near a coast, swimming pool or spa will cause the barbecue to corrode (Oxidize). Cover your barbecue for rust protection.

HARDWARE LIST

Char-Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-9

REPLACEMENT PARTS LIST

FOR 468972023 & 468782023Char-Broil-468972023-Professional-Power-
Edition-2-Burner-FIG-11

REPLACEMENT PARTS DIAGRAM

FOR 468972023 & 468782023Char-Broil-468972023-Professional-Power-
Edition-2-Burner-FIG-12

ASSEMBLY

Char-Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-13 Char-Broil-468972023
-Professional-Power-Edition-2-Burner-FIG-14 Char-Broil-468972023-Professional-Power-Edition-2
-Burner-FIG-15 Char-
Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-16Char-Broil-468972023
-Professional-Power-Edition-2-Burner-FIG-17 Char-Broil-468972023-Professional-Power-Edition-2
-Burner-FIG-18

LEAK CHECK FOR 468782023Char-Broil-468972023-Professional-Power-Edition-2
-Burner-FIG-19 Char-
Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-20 Char-Broil-468972023
-Professional-Power-Edition-2-Burner-FIG-21 Char-Broil-468972023-Professional-Power-Edition-2
-Burner-FIG-22 Char-
Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-23 Char-Broil-468972023
-Professional-Power-Edition-2-Burner-FIG-24 Char-Broil-468972023-Professional-Power-Edition-2
-Burner-FIG-25Char-
Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-26 Char-Broil-468972023
-Professional-Power-Edition-2-Burner-FIG-27 Char-Broil-468972023-Professional-Power-Edition-2
-Burner-FIG-28 Char-
Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-29 Char-Broil-468972023
-Professional-Power-Edition-2-Burner-FIG-30

  • Inspect your infrared grate before each use to ensure that the openings are not covered with debris. See the Grilling Guide for detailed cleaning instructions.

Char-Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-31Char-Broil-468972023
-Professional-Power-Edition-2-Burner-FIG-32 Char-Broil-468972023-Professional-Power-Edition-2
-Burner-FIG-33 Char-
Broil-468972023-Professional-Power-Edition-2-Burner-
FIG-34Char-Broil-468972023
-Professional-Power-Edition-2-Burner-FIG-35

  • Leak test before first use, at least once per year, and every time the gas tank is changed or disconnected.

Warranty Statement

  • Char-Broil Europe GmbH of Paul-Dessau-Straße 8 Quartier O – 4.OG D-22761 Hamburg, (Char-Broil) warrants to the PURCHASER of this Char-Broil product that it will be free of defects in material and workmanship from the date of purchase as follows:

| Gas Grills
---|---
Burners| 10 years
Cooking Grates/Emitters| 3 years
All Other Parts (EURO minimum)| 2 years

  • Char-Broil or the seller of the product may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR SALES RECEIPT OR INVOICE.
  • [France only: All products sold by the Seller are covered by the legal warranties provided in Articles 1641 and followings of the Civil Code (warranty against hidden defects) and Articles L. 217-1 to L. 217-14 and L. 411-1 to L. 411-2 of the Consumer Code (warranty of conformity.]
  • This Warranty includes the right of repair or replacement of the product or parts of the product that prove defective under normal use and service. Before returning any parts, you should promptly contact Char-Broil using the contact information on our website. In case of a defect, Char-Broil will elect to replace or repair the product or such parts without charge. . Char-Broil will return the product or parts of the product to the purchaser, freight or postage prepaid. If Char-Broil elects to repair the product or such defective parts of the product and this repair fails, you are entitled, pursuant to your statutory legal rights, to reduce the purchase price or to withdraw from the contract and receive a refund.
  • This Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, vandalism, improper installation or improper maintenance or service, or failure to perform normal and routine maintenance, including but not limited to damage caused by insects within the burner tubes, as set out in this owner’s manual. Exceptions may apply, so please contact Char-Broil or your seller in case you have any questions on whether this Warranty applies to your specific case or not.
  • Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes, discoloration due to exposure to chemicals either directly or in the atmosphere, is not covered by this Warranty, and are not normally covered by your statutory legal rights.
  • Char-Broil is not liable for any unforeseeable losses (i.e. loss or damage that neither you nor Char-Broil or the seller contemplated at the time of purchase), or any damage caused by you, save for that Char-Broil’s liability for fraud or death or personal injury caused by its negligence is not limited.
  • Char-Broil does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment; and no such representations are binding on Char-Broil.
  • This Warranty applies only to products sold at retail to individuals (as opposed to businesses) within the European Union.
  • This Warranty does not affect any of your statutory legal rights under the applicable consumer laws of your resident country.
  • For warranty service, contact Char-Broil at info-eu@CHARBROIL.EU.
  • NOTE: This intormason is a guide only. Items incuded in your BBQ spechicaton may difer depending on region or specfic dealer spechcañon.
  • All specifications are subject to change without notice.
  • Char-Broil® Europe GmbH Paul-Dessau-Strasse 8 Quarter O – 4th floor D-22761 Hamburg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Char-Broil User Manuals

Related Manuals