DS18 MARINE & POWERSPORT HEAD UNIT Installation Guide
- June 5, 2024
- DS18
Table of Contents
MARINE & POWERSPORT HEAD UNIT
Installation Guide
MRX2
MARINE & POWERSPORT HEAD UNIT
Please read the instruction manual carefully before operating the unit.
SAFETY INSTRUCTION
CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of
important instructions. Failure to heed the instructions could result in
injury or unit damage.
To prevent injury and damage to the unit, please read and follow the
instructions in this manual. If you feel unsure about installing this system
yourself, have it installed by a qualified technician.
Before installation, disconnect the battery negative (-) terminal to prevent
damage to the unit, fire, and/or possible injury.
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, according to part 15 of the FCC Rules. These limits are
designed to provide more reasonable protection against harmful interference in
a residential installation.
Operation is subjected to the following two conditions: (1) This device may
not cause harmful interference, and (2) the device must accept any
interference received, including interference that may cause undesired
operation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, you are encouraged to try to
correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SPECIFICATIONS
GENERAL:
Operating Voltage: | 10.5 – 16 Volts |
---|---|
Low Voltage Warning Alert: | YES (< 11V) |
Waterproof Rating: | IPX6 |
UV/Salt Protection: | YES |
Buttons: | Rubber + RGB Backlit (synced with LCM) |
Screen Panel: | Gorilla Glass with OCA Full Bonding |
DISPLAY:
Type: | 3” Liquid Cristal Module |
---|---|
Backlight: | 7 Colors Selectable |
(Auto / White / Red / Blue / Green / Purple / Cyan /Yellow)
AUDIO:
Power Output:|
---|---
RMS:| 4 x 15W @ 4ohm
| 4 x 25W @ 2ohm
Max:| 4 x 50W @ 2ohm
Min Load:| 2 ohm Stable per Channel
Frequency Response:| 20Hz to 20Khz
RCA Pre-Out Voltage:| 4 Volts
Output Impedance:| 500ohm
Equalizer:| 2 Bands (Bass 80Hz, Treble12Khz)
Presets:| YES (S-Bass / Vocal /Powerful/clarity)
Subwoofer Control:| Level (-10 to +10)
Audio Zones:| 2 Zones (Stereo + Subwoofer each)
Independent Zone Control:| YES (Level/Tone)
Audio Input:| L+R RCA (Aux Input)
TUNER:
FM Frequency Range: | 87.5 – 107.9 MHz |
---|---|
AM Frequency Range: | 530 – 1710 KHz |
Weather Band: | 162.40 – 162.55 MHz |
NOAA Weather Band: | YES Compatible |
Tuner Presets: | 18 FM / 12 AM / 6 WB |
Radio Data System: | YES (AF / TA / NEWS) Selectable |
CONNECTIVITY:
Bluetooth Version: | 5.0 + EDR |
---|---|
Audio Streaming: | A2DP |
USB Compatibility: | v2.0 |
USB Capacity: | 64 Gb Max |
USB Charge Capacity: | 2.1Amp |
Audio Files Compatibility: | MP3, WMA |
Remote Control: | Wired 3.5mm Jack Input (Compatible with MXRC) |
INSTALLATION/ MOUNTING
ACCESSORIES
- Main Unit”
- Power/Speaker Harness
- Screws X 2PCS
- Hex Head Screws X 2PCS
- U Bracket
- Instruction Manual
CAUTION
- This player should be installed by a professional technician.
- Please read the instruction and operation of the equipment carefully before installing it.
- Make sure to connect other wires before power connection.
- To avoid a short circuit. Please make sure all the exposed wires are insulating.
- Please fix all the wires after installation. 6. Please make the connection to the player accordingly to this instruction manual. A wrong connection may cause damage.
- This player only fits for a 12V DC device and please make sure your boat belongs to this kind of cathode grounding electrical system.
- Please connect the wires rightly. A wrong connection will cause malfunction or damage the electrical system.
MOUNTING (USING U BRACKET)
To mount the unit, you will need to find a flat surface with adequate clearance behind it that provides enough clearance for the unit and all its necessary wiring.
- Once you have determined a mounting location, you will need to cut a circular hole 3″ {77mm) in diameter.
- After the hole is cut slide the unit and wiring through the hole.
- Take the U bracket and slide over the two studs on the back of the unit. Tighten down with supplied nuts.
- Plug in all wiring harnesses and cables. Refer to the wiring diagram for wire harness connection types.
WIRING CONNECTION
PIN NO.
| WIRE COLOR| WIRE DEFINITION|
AWG
---|---|---|---
1| BLACK| GROUND (-)| 16
2| PURPLE/BLACK| SPEAKER REAR RIGHT (-)| 20
3| PURPLE| SPEAKER REAR RIGHT (+)| 20
4| BLUE| ANT (+12V OUT)| 20
5| GREEN/BLACK| SPEAKER REAR LEFT (-)| 20
6| GREEN| SPEAKER REAR LEFT (+)| 20
7| RED| ACC (+12V IN)| 20
8| GREY/BLACK| SPEAKER FRONT RIGHT (-)| 20
9| GREY| SPEAKER FRONT RIGHT (+)| 20
10| YELLOW| B+ (+12V IN)| 16
11| WHITE/BLACK| SPEAKER FRONT LEFT (-)| 20
12| WHITE| SPEAKER FRONT LEFT (+)| 20
CAUTION
- This player can only be used by the 12V DC cathode grounding electrical system.
- Do not connect the battery terminals until the player is fully assembled.
- Please make sure to connect the yellow wire to the positive of the battery(+).
- When changing the fuse. Please make sure the specifications are the same.
- Using good quality 4-2 ohm speaker can enhance the audio performance of the system.
MEASUREMENTS
BASIC OPERATION
-
POWER/button
Press **** the button to turn it on. Press the key again to turn off the unit. -
BAND/button
Press the BAND button to FM1/FM2/FM3/AM1/AM2/WB. Press and hold the BAND button for 3 seconds to auto store the stations. -
DISP / button
Shortly press the DISP button to show the clock, then press and hold the DISP button again to set time, Rotate Vol to set the hour time display, press the DISP key again to turn to the minute time display, rotate Vol to set minute time display. After setting the time, it will automatically save and exit within 5 seconds. -
ZONE/button
Press the ZONE button to ZONE1 / ZONE2 / ZONE1+ZONE2. -
PLAY / PAUSE button
In RADIO/AUX source press the button for the MUTE on/off function. In the USB/BT source press the button for the Pause / Play function. -
Seek UP button In RADIO source, shortly press button to Seek up, press and hold the button to show next station. In the USB/BT source press ****button to the next song/file and press and hold the button to fast forward play.
-
Seek the DOWN button
In RADIO source, shortly press the button to Seek down, press and hold the button to show back to the previous station. In the USB/BT source press ****button to the previous song/file, and press and hold the button to playback quickly. -
SRC button
Press the SRC button to Mode change Radio / BT / USB / AUX-IN. -
VOL / SEL button
Rotate the Vol to adjust the volume.
SEL BUTTON FUNCTIONS:
-
IN ZONE1 or ZONE2, AUX/BT mode : Shortly press SEL button to BAS / TRE / SUB / EQ (rotate the VOL to select FLAT / OFF, S-BASS, VOCAL, POWERFUL, CLARITY) / LOUD (ON / OFF) / COLOR LIGHT (rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN) / BEEP (OFF/ON) one by one.
Press and hold SEL button to TA (OFF / ON ) / AF (OFF / ON) / NEWS (OFF / ON) one by one. -
IN ZONE1 or ZONE2, RADIO mode: Shortly press SEL button to BAS / TRE / SUB / EQ (rotate the VOL to select FLAT / OFF, S-BASS, VOCAL, POWERFUL, CLARITY) / LOUD (ON/OFF) /COLOR LIGHT (rotate the VOL to select AUTO, WHITE, PURP, CYAN,YELLOW, RED, GREEN) / BEEP (ON/OFF) / STEREO (MONO) / LOCAL (DX) one by one.
Press and hold SEL button to TA (OFF / ON) / AF (OFF / ON) / NEWS (OFF / ON) one by one. -
IN ZONE1 or ZONE2, USB mode : Shortly press SEL button to BAS / TRE / SUB /EQ (rotate the VOL to select FLAT / OFF, S-BASS, VOCAL, POWERFUL, CLARITY) / LOUD (ON / OFF) / COLOR LIGHT (rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN) / BEEP (OFF / ON) one by one. Press and hold SEL button to RDM( then rotate the VOL to select OFF/FOLD/ALL) / RPT(then rotate the VOL to select ONE / FOLD / ALL) / TA (OFF / ON) /A F (OFF / ON) / NEWS (OFF / ON) one by one.
-
IN ZONE1 + ZONE2, AUX/BT mode: Shortly press SEL button to COLOR LIGHT (rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN) / BEEP (OFF/ON) one by one.
Press and hold SEL button to TA (OFF / ON) / AF (OFF / ON) / NEWS (OFF / ON) one by one. -
IN ZONE1 + ZONE2, RADIO mode : Shortly press SEL button to COLOR LIGHT (rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN) / BEEP (OFF / ON) / STEREO (MONO) / LOCAL (DX) one by one.
Press and hold SEL button to TA (OFF / ON) /AF (OFF / ON) / NEWS (OFF / ON) one by one. -
IN ZONE1 + ZONE2, USB mode : Shortly press SEL button to COLOR LIGHT (rotate the VOL to select AUTO, WHITE, PURP, CYAN, YELLOW, RED, GREEN) / BEEP (OFF / ON).
Press and hold SEL button to RDM (then rotate the VOL to select OF F/ FOLD / ALL) / RPT (then rotate the VOL to select ONE / FOLD / ALL )/ TA (OFF / ON) /AF (OFF/ON) / NEWS (OFF / ON) one by one.
FUNCTION SETTING / OPERATION
SETTINGS
DX / LOC (Distance / Local):
LOC: Receive the strong signal station only in seek station.
DX: Receive strong and weak signal station in seek station.
STEREO / MONO:
STEREO: Receive FM stereo signal.
MONO: Change FM stereo to monophonic. It can reduce the noise when the
signal is weak.
RESET THE UNIT Press and hold the ab button for 5 seconds to reset the
unit.
RADIO (AM / FM / WB) OPERATION
Press the SRC button to select the Radio source option (FM / AM / WB). To auto
seeks station, press and hold the BAND button for 3 seconds to the auto store
radio station. To manual seek a station, shortly press / button to
Seek up/down the radio station, press and hold thee / button to next
/ previous station.
USB OPERATION
After your device is connected to the source unit, this feature allows you to
control the playback of your device directly from the unit. Press the SRC
button to select the USB source option.
To play or pause a song, short press the PLAY/PAUSE button. To skip a track
forward, short press the FWD button. To skip a track backward, short press the
REV button.
To access USB-specific settings, Press and hold the SEL button for the list of
settings (Random play>Repeat). Use the encoder to select the option to change.
AUX (AUXILIARITY INPUT) OPERATION
After your device is plugged into the source unit, this feature allows you to
play music from your device. Press the SRC button to select the AUX source
option and use your plugged-in device to control song/track selection, PLAY /
PAUSE, and track skip FWD / REV.
BLUETOOTH OPERATION
After your device is paired to the source unit, this feature allows you to
control the playback of your device directly from the unit. Press the SRC
button to select the BLUETOOTH source option. Then search and select the
Bluetooth device “MRX2” from your phone and input the password “0000” If it
needs. When paired successfully, the BT symbol will be shown on the LCD. To
play or pause a song, short press the PLAY / PAUSE button. To skip a track
forward, short press the FWD button. To skip a track backward, short press the
REV button.
TROUBLESHOOTING
TROUBLE | CAUSE | SOLUTION |
---|
Bask
Unit does not turn on| Blown fuse| Check the fuse of the unit, and replace it
with the correct rating.
The vehicle’s ignition is off| If connected following the instructions, the
unit will not operate with ignition off
The voltage applied to Red wire is not between 10.5 & 16 volts or there is no
voltage present.| Check battery, connections, and fuses and repair or replace
as necessary. If voltage is above+ 16 volts, have the electrical system
inspected by an authorized service center.
The unit is not properly grounded.| Check wiring and repair as necessary.
Radio Tuner
The tuner fails to tune any stations| No antenna or disconnected or open
connection in cable.| Check all connections and repair as necessary.
Unable to tune stations in seek mode| You are in a weak signal area.| Make
sure the tuner LOC mode is off.
USB Devices
The USB device cannot be inserted| The USB device has been inserted in the
wrong direction.| Reversing the connection direction of the USB device, try
reinserting.
The USB device connector is broken.| Replace with a new USB device.
The USB device is not recognized| The USB device is damaged.| Disconnect the
USB device and reconnect. If the device is still not recognized, try replacing
it with a different USB device.
Connectors are loose.
No Sound was heard with the display No File” shown| No MP3 / WMA files are
stored on the USB device.| Store these files properly on the USB device.
Sound skip or is noisy| MP3 / WMA files are not created properly.| Use MP3/WMA
files that are encoded correctly.
MP3 is not playing back| Writing error occurred. The MP3 format is not
compatible.| Make sure MP3 has been written in a supported format.
Bluetooth
Cannot pair Bluetooth| The Bluetooth function of the device is not enabled.|
Refer to the user manual of the device for how to enable the Bluetooth
function.
The audio quality is poor after connection with a Bluetooth enabled device|
The Bluetooth reception is poor.| Move the device closer to the audio system
or remove any obstacle between the device and the system antenna.
Refer to the user manual of the device for how to enable the Bluetooth
function.
Move the device closer to the audio system or remove any obstacle between the
device and the system antenna.
MARINE & POWERSPORT HEAD UNIT
FOR MORE INFORMATION PLEASE VISIT DS18.COM
We LIKE IT LOUD
FCC ID: 2AYOQ-MRX2 This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>