B-TECH BT7888 Slide-Out AV Storage Tray Installation Guide

June 9, 2024
B-TECH

BT7888
SLIDE-OUT
AV STORAGE TRAY
INSTALLATION GUIDEB-TECH BT7888 Slid Out AV Storage Tray
-

SPECIFICATIONS

  • Slide-out storage tray fixes directly to the wall, ideal for mounting AV equipment behind a screen
  • Designed for a variety of different sized AV devices
  • Suitable for portrait or landscape orientation -Tray can be mounted to slide out left, right or down
  • Removeable tray with quick release
  • Bracket Dimensions: 590 x 350 x 35mm (23.23 x 13.78 x 1.38″)
  • Max AV equipment size: 450 x 250 x 50mm (17.72 x 9.84 x 1.97″)
  • Locks into position when opened and closed – If required a padlock (not supplied) can be added for extra security

**INSTALLATION SAFETY INSTRUCTIONS

**

CAUTION: This mount is intended for use only with the maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury.

Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference. Please check carefully to make sure there are no missing or defective parts – defective parts must never be used. B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other suitably qualified person install this product. Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and easily damaged if dropped. If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious injury or death both during installation and at any time thereafter. Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing. This weight limit will be clearly stated on each product and its packaging and will vary from product to product.
Product location
Please pay careful attention to where this product is located. Check load capacity of the wall prior to installation as some surfaces are not suitable for installation. Designed for indoor use, this mount is suitable for public or home installation If located in a public or frequently populated area ensure that the product is out of the immediate reach of people. If any AV equipment is to be suspended over the likely path or location of people then great care should be taken to secure all parts of the installation from falling. When drilling holes it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. The fixing kit supplied with the product may not be suitable for all walls. If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up. Immediately after installation double- check that the work done is safe and secure. Double-check all necessary fixings are present and are of ample tightness. It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more than 6 months apart) to ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably qualified person.

PARTS LIST

PLEASE KEEP THIS FOR FUTURE REFERENCE

B-TECH BT7888 Slid Out AV Storage Tray - fig 1

ITEM DESCRIPTION QTY
1 WALL PLATE 1
2 SLIDING PLATE 1
3 AV STORAGE TRAY 1
4 No.8 x 30mm WALL PLUG 4
5 M6 x 30mm CSK WOOD SCREW 4
6 CABLE TIE L100m x W2.5mm 8
7 CABLE TIE L400mm x WSmm 8

Max load: 10 kg (22 lbs)

B-TECH BT7888 Slid Out AV Storage Tray - fig 2

INSTALLATION NOTES

PRE-INSTALLATION
The AV storage tray has been designed to be wall mounted behind a screen. The installer must choose a suitable location for the tray to avoid blocking any air ventillation on the back of the screen and that it does not prevent access to any screen plugs / cables, etc. The storage tray can be mounted in a portrait orientation by the side of the screen wall mount for a left or right side release, or where space is limited, the storage tray can also be mounted below the screen wall mount in a landscape orientation for a slide down release. When choosing a screen wall mount ensure that there is enough space between the screen and the wall for the storage tray and the AV equipment. Minimum distance from behind the screen to the wall is 55mm (2.16″).
Note: If required, use spacers from the screen mount to increase the distance between the screen and the wall. See Product Dimensions (page 11) for reference & max sizes of the AV equipment.

B-TECH BT7888 Slid Out AV Storage Tray - fig 3

INSTALLATION INSTRUCTIONS

  1. REMOVE STORAGE TRAY FROM WALL MOUNT
    Open the key on item 2 and remove item 3.B-TECH BT7888 Slid Out AV Storage
Tray - fig 4

  2. FIX MOUNT TO THE WALL
    i. Mark & drill holes in the wall for item 1.
    ii. Mount item 1 to the wall using items 4* & 5.
    Important: As the product will be located behind a screen, determine a suitable location in conjunction with the screen wall mount before installing the product (see page 5).B-TECH BT7888 Slid Out AV Storage Tray - fig
5

  3. PULL SLIDING PLATE OUT
    Push the lock to release item 2 and pull the sliding tray out.B-TECH BT7888
Slid Out AV Storage Tray - fig 6B-TECH BT7888 Slid Out AV Storage Tray - fig
7

  4. ATTACH AV EQUIPMENT TO THE TRAY
    Place the AV devices on item 3 and position them so that all cables can be easily connected.
    Use the long cable ties (item 7) to secure the equipment to the tray.B-TECH
BT7888 Slid Out AV Storage Tray - fig 8

  5. MOUNT STORAGE TRAY
    Fix item 3 back onto item 2 and secure in place using the locking keys on item 2.B-TECH BT7888 Slid Out AV Storage Tray - fig 9

  6. CONNECT CABLES
    Use the small cable ties (item 6) to tidy cables to item 3.B-TECH BT7888
Slid Out AV Storage Tray - fig 10

  7. STORAGE TRAY
    • Once all AV devices are connected, fully push item 2 back into item 1 to lock the tray in place.B-TECH BT7888 Slid Out AV Storage Tray - fig
11

TYPICAL INSTALLATIONS

B-TECH BT7888 Slid Out AV Storage Tray - fig 12

Note: If required, use spacers from the screen mount to increase the distance between the screen and the wall. The BT7888 is also compatible with B-Tech professional systems for pole, column and rail mounting.

B-TECH BT7888 Slid Out AV Storage Tray - fig 13

BT7888 DIMENSIONS

PLEASE KEEP THIS FOR FUTURE REFERENCE
PORTRAIT ORIENTATION
FRONT VIEW – CLOSED

B-TECH BT7888 Slid Out AV Storage Tray - fig 14

CONTACT: info@btechavmounts.com
©2022 B-Tech International Design and Manufacturing Ltd. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design and Manufacturing Ltd.
B-Tech AV Mounts and the B-Tech logo are registered trade marks.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
AMA-BT7888-V1-PROBX-0922-129 MADE IN VIETNAM
For More Information Visit www.btechavmounts.com https://www.btechavmounts.com/bt7888

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

B-TECH User Manuals

Related Manuals