StarTech Com 4PORT-8K-HDMI-SWITCH 4-Port HDMI Video Switch User Guide
- June 9, 2024
- StarTech com
Table of Contents
StarTech Com 4PORT-8K-HDMI-SWITCH 4-Port HDMI Video Switch
Product ID
Component | Function |
---|---|
1 | Power LED Indicator |
- Solid Red: HDMI Switch in Standby Mode
- Solid Blue: HDMI Switch is powered on and operational
2| Port Selection Indicators|
- Solid Blue: HDMI Input Port is active
3| Auto Switching Indicator|
- Solid Blue: Automatic Switching is enabled
- LED Off: Automatic Switching is disabled
4| IR Mode Indicator|
- Solid Blue: IR Receiver enabled, Remote Control will operate the HDMI Switch
- LED Off: IR Receiver disabled, Remote Control will not operate the HDMI Switch
5| Push Button Selector|
- Switch between HDMI Inputs 1 – 4
6| USB Power Input|
- Connect the included USB Wall Charger and USB Micro-B Power Cable
7| HDMI Output Port|
- Connect to an HDMI Display
8| HDMI Input Ports|
- Connect to an HDMI Source Device
9| Mounting Bracket Screw Holes|
-
Connect the included Mounting Brackets
-
Holes are on each side of the HDMI Video Switch
-
Front
-
Rear
-
Side
-
Remote Control
Product Information
For the latest manuals, product information, technical specifications, and declarations of conformance, please visit: www.StarTech.com/4PORT-8K-HDMI- SWITCH
Package Contents
- HDMI Video Switch x 1
- Remote Control (Batteries Not Included) x 1
- Mounting Kit x 1
- USB Wall Charger x 1
- USB Micro-B Power Cable x 1
- Rubber Feet x 4
- Quick-Start Guide x 1
Requirements
- HDMI Source x 4
- HDMI Display x 1
- HDMI Cables (sold separately) x 5
- AAA Batteries (for remote control) x 2
- Philips Head Screwdriver x 1
Installation
(Optional) Mounting Kit
Note: Before mounting the HDMI Video Switch make sure that the surface
you are mounting to is strong enough to support the weight of the HDMI Video
Switch. It is recommended that you mount the HDMI Video Switch on a wall stud
to provide the correct support.
- Determine the Mounting Surface for the HDMI Video Switch.
- Place the Mounting Brackets on each side of the HDMI Video Switch. Align the Holes in the Mounting Brackets with the Holes on the sides of the HDMI Video Switch.
- Insert two Screws from the included mounting kit through each Mounting Bracket and into the HDMI Video Switch.
- Tighten each Screw using a Phillips Head Screwdriver.
- Mount the HDMI Video Switch to the desired Mounting Surface using the appropriate Mounting Hardware (e.g. Wood Screws).
HDMI Video Switch
Note: Ensure your HDMI Source Device, and the HDMI Displays are powered off
before you begin installation.
-
Connect an HDMI Cable (sold separately) from an HDMI Source Device to HDMI Input 1 on the HDMI Switch.
-
Repeat Step 1 for HDMI Input 2 – 4.
Note: Each HDMI Port is numbered, please take note of which number is assigned to each HDMI Source Device. -
Connect an HDMI Cable (sold separately) to the HDMI Output Port on the HDMI Switch and to an HDMI Input Port on the HDMI Display.
-
Connect the USB Wall Charger and USB Micro-B Power Cable to an available Power Source and to the USB Power Input on the HDMI Switch.
-
Power on the HDMI Display, followed by each of the HDMI Source Devices
Operation
Push Button Operation
Short Press
Press the Push Button Selector to switch between HDMI Inputs 1 – 4. In Auto
Mode, the HDMI Switch will cycle between the HDMI Inputs with an active HDMI
signal, from
1 to 4. If the HDMI Switch is not in Auto Mode, the unit will cycle between
all inputs, from 1 to 4, even if there is no attached Source Device.
3-5 Second Button Press Enable or disable the Automatic Switching feature of
the HDMI Switch. For example, if you are watching TV and would like to watch
your Blu-ray player, turn the Blu-ray player on. To switch back to the TV you
can turn the Blu-ray player off, or switch the TV Box back on after being
switched off, when the Blu-ray player is active.
6 Second Button Press Enable or disable the IR functionality of the HDMI
Switch. The IR Functionality enables use of the HDMI Switch’s included Remote
Control.
Remote Control Operation
Note: Ensure the IR Mode Indicator on the front of the HDMI Switch is
solid blue, indicating that IR Functionality is enabled.
Remove the backplate from the Remote Control and install the 2x AAA Batteries
(not included). Point the Remote Control at the front of the HDMI Switch.
Press the “1”, “2”, “3” or “4” Button to manually switch between HDMI Inputs.
Using the “IR” Button will disable the IR Functionality of the HDMI Switch.
Note: To re-enable IR Functionality, see the section “6 Second Button Press”
under “Push Button Operation”
Regulatory Compliance
FCC – Part 15
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by
StarTech.com could void the user’s authority to operate
the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
References
- 4-Port 8K HDMI Switch, HDMI 2.1 Switcher - Video Switchers | StarTech.com
- You | Fabricant de cuisines aménagées & salles de bains sur-mesure
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>