Ditec IP2269 Entrematic ZEN 2C Remote Control User Manual

June 9, 2024
Ditec

Ditec IP2269 Entrematic ZEN 2C Remote Control
Ditec IP2269 Entrematic ZEN 2C Remote Control

Factory default channel configuration

Manual configuration

Configuration with PC
Refer to Ditec ZEN Manager system documentation.
Manual configuration

  • Last version of this manual

Specification

Transmitters Frequency Radiated power Type Power supply Channels Range
ZEN2** 433,92MHz < 1mW Rolling code Battery type CR2032 2 50-150m
ZEN4*** 4
ZEN2C Fixed code 2
ZEN4C 4
ZENP2 / ZENP2MT 868,35MHz < 1mW AES-128 rolling code **** Use batteries
of indicated type. 2
ZENP4 / ZENP4MT 4

[**] Models ZEN2, ZEN2B, ZEN2G, ZEN2R, ZEN2W, ZEN2Y, ZEN2MT
[***] Models ZEN4, ZEN4W, ZEN4MT

WARNING: Product contains coin/button cell battery
**

**

  • Keep product and batteries away from children
  • Battery can cause severe or fatal injuries in 2 hours or less if swallower or placed inside any part of the body
  • Seek immediate medical attention if it is suspected that a coin/button cell battery has been swallowed or placed inside any part of the body.

All models

[A] Direct programming
  1. Activate Receiver Learning mode (refer to specific product manual)

  2. Press button on NEW TX

  3. Wait

[B] Battery save function enable-disable
  1. Press simultaneously
    Battery save function enable-disable
    Factory enabled in all models
    Do not use remote controls to perform hold-to-run operations

  2. Enable
    Battery save function enable-disable
    Disable
    Battery save function enable-disable

[C] Encoding type check
  1. Keep pressed button to be checked
    Encoding type check
N Encoding
0 Fixed code
1 “Dip-switch”
2 Rolling code
3 “MM53200” clone
4 AES
5 Protected

Battery save function must be enabled

[D] Battery replacement
  1. Open housing

  2. Take out battery

  3. Insert new battery

Only models ZEN2C-ZEN4C

[E] Factory RESET
  1. Take out battery

  2. Keep pressed buttons as shown

  3. Keeping buttons pressed re-insert battery

[F] Existing TX full duplication
  1. With NEW TX

Also compatible with: BIXLS2

  1. With EXISTING TX, within 10s
[G] manual code setting
  1. With NEW TX
    manual code setting
    Example:
    Code 0 1 0 0 1 0 0 1 0 0
    manual code setting

  2. Insert sequence of ten “0” or “1” Confirmation blinks:
    manual code setting

[H] Generic TX single-button duplication
  1. With NEW TX

  2. Again with NEW TX, within 10s
    Generic TX single-button duplication

  3. Press and release button on NEW T on which duplicate generic TX (example)

  4. Within 10s press desired button on generic TX
    Generic TX single-button duplication
    Compatible with 433MHz products with “MM53200” encoding or similar

Only models ZEN (2/2B/2G/2R/2W/2Y/2MT/4/4W/4MT)

[I] Add NEW TX by existing TX
  1. Go near the gate

  2. With EXISTING (programmed) TX
    Add NEW TX by existing TX

  3. Again with EXISTING TX
    Add NEW TX by existing TX

  4. With NEW TX, within 10s

  5. Wait

[J] Enable-disable AES encryption
  1. Take out battery

  2. Keep pressed button as shown
    Case a) buttons 1 / 1-2

Case b) buttons 2 / 3-4

  1. With button pressed re-insert battery

AES enabled-disabled on the indicated buttons
Enable-disable AES encryption
Mode verification

The procedure toggles AES mode (ON-OFF-ON-OFF…). AES decoder available only on new generation receivers or control units – refer to specific product manual

EC and UK Declaration of Conformity

The manufacturer, ASSA ABLOY Entrance Systems AB, with registered office at Lodjursgatan 10, SE-261 44 Landskrona, Sweden declares that the type of radio equipment ZEN2/ZEN2B/ ZEN2C/ZEN2G/ZEN2R/ZEN2W/ZEN2Y/ZEN2MT/ZEN4/ZEN4C/ZEN4W/ ZEN4MT/ZENP2/ZENP2MT/ZENP4/ZENP4MT complies with:
EC Directive
RED Directive 2014/53/UE

UK Regulations
Radio Equipment Regulations 2017

The crossed-out wheeled bin symbol indicates that the product should be disposed of separately from household waste. The product should be handed in for recycling in accordance with local environmental regulations for waste disposal.
By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or landfill and minimize any potential negative impact on human health and the environment.

Technical data subject to change without notice

icon ASSA ABLOY Entrance Systems AB
Lodjursgatan 10
SE-261 44, Landskrona
Sweden
© ASSA ABLOY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals