Milwaukee M18ONEFPRT 18V 2 x 2.0Ah Li-Ion RedLithium Brushless Cordless Rivet Gun Instruction Manual

Milwaukee M18ONEFPRT 18V 2 x 2.0Ah Li-Ion RedLithium Brushless Cordless

Rivet Gun

Assembly Instruction

TECHNICAL DATA

• Type Rivet tool

• Production code 4831 05 01 XXXXXX MJJJJ

• Battery voltage 18 V

• Frequency band(s) of Bluetooth 2402 – 2480 MHz

• Radio-frequency power 1,8 dBm

• Bluetooth version 4.2 BT signal mode

• Pull force 20000 N

• Tool stroke length 30,0 mm

• Jaw diameter max. 7,0 mm

• Rivet size Ø
  Black 4,8 mm
  Red 6,0 mm
  Green 6,4 mm
  Brown 7,0 mm

• Rivet material Aluminium
  Copper
  Steel
  Stainless steel

• Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah … 12,0 Ah) 2,5 … 3,5 kg

• Recommended Ambient Operating Temperature 0 … +50 °C

• Recommended battery types M18B…; M18HB…

• Recommended charger M12-18…; M1418C6

• Noise information: Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
  Sound pressure level / Uncertainty K
  Sound power level / Uncertainty K
  Wear ear protectors!
  81 dB (A) / 3dB (A)
  92 dB (A) / 3dB (A)

• Vibration information: Vibration total values (triaxial vector sum) determined according to EN 62841. Vibration emission value ah / Uncertainty K < 2,5 m/s2 / 1,5 m/s2

WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

WARNING! Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.

RIVET TOOL SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Use protective equipment. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
Have damage repaired immediately by an authorised workshop.
Remove the battery pack before starting any work on the appliance.
To avoid injury and damage, never immerse the tool, removable battery or charger in liquid or allow liquid to penetrate them.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
WARNING! To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., Can cause a short circuit.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.
Use only System M18 chargers for charging System M18 battery packs. Do not use battery packs from other systems.

WARNING! This device contains a button-type/coin cell lithium battery. A new or used battery can cause severe internal burns and lead to death in as little as 2 hours if swallowed or if it enters the body. Always secure the cover on the battery compartment. If it does not close securely, stop the device, remove the battery and keep it out of reach of children. If you believe that someone has swallowed the battery or that it has otherwise entered the body, seek immediate medical attention.

SPECIFIED CONDITIONS OF USE
This blind riveting power tool is designed for professional blind rivet setting applications.
Do not use the product in any way other than those stated for intended use.

RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:

• Injury caused by vibration. Hold the product by designated handles and restrict working time and exposure.
• Exposure to noise can cause hearing injury. Wear ear protection and limit exposure.
• Injury due to flying debris Wear eye protection, heavy long trousers, gloves and substancial footwear at all times.
• Inhalation of toxic dusts.

NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean. For an optimum life-time, the battery packs have to be fully charged, after use.
To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% – 50% charged condition
Every six months of storage, charge the pack as normal.

Battery protection for Li-Ion batteries
In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will flash,and then the tool will turn OFF.
To reset, release the trigger. Under extreme circumstances, the internal temperature of the battery pack could raise too much. If this happens, the fuel gauge will flash until the battery pack cooled down. After the lights go off, the work may continue.

Transporting Lithium Batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.
The user can transport the batteries by road without further requirements.
Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

When transporting batteries:
Ensure that battery contact terminals are protected and insulated to prevent short circuit.
Ensure that battery pack is secured against movement within packaging. Do not transport batteries that are cracked or leak. Check with forwarding company for further advice.

ONE-KEY™
To learn more about the ONE-KEY functionality of this device, please refer to the Quick Start guide included with this product or go to http://www.milwaukeetool.com/one-key.
To download the ONE-KEY app, visit the App Store or Google Play from your smart device.
Also, when the product experiences ESD, the Bluetooth communication will be disconnected. It needs to be reset
manually to recover. We considered the results to be within our minimum acceptable performance level according to EN 55014-2 / EN 301 489-1 / EN 301 489-17.

CLEANING
The ventilation slots of the machine must be kept clear at all times.

MAINTENANCE

Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the Article No. as well as the machine type printed on
the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.

SYMBOLS

• Please read the instructions carefully before starting the machine.
• CAUTION! WARNING! DANGER!
• Remove the battery pack before starting any work on the appliance.
• Do not swallow the coin cell battery!
• Always wear goggles when using the machine.
• Wear gloves!
• Accessory – Not included in standard equipment, available as an accessory.
• Do not dispose of electric tools together with household waste material. Electric tools and electronic equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Check with your local authority or retailer for recycling advice and collection point.
• Voltage
• Direct Current
• European Conformity Mark
• British Conformity Mark
• Ukraine Conformity Mark
• EurAsian Conformity Mark

EC-DECLARATION OF CONFORMITY

We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfills all the listed below relevant regulations and the directives and harmonized standards have been used.
2011/65/EU (RoHS)
2006/42/EC
2014/53/EU
EN 62841-1:2015
EN 55014-1:2017+A11:2020 EN 55014-2:2015
EN 62479:2010
EN 300 328 V2.2.2
EN 301 489-1 V2.2.3
EN 301 489-17 V3.2.4
EN IEC 63000:2018
Winnenden, 2021-01-19
Alexander Krug
Managing Director
Authorized to compile the technical file

GB-DECLARATION OF CONFORMITY

We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfills all the listed below relevant regulations and the directives and harmonized standards have been used.
S.I. 2012/3032 (as amended) S.I. 2008/1597 (as amended) S.I. 2017/1206 (as amended)
BS EN 62841-1:2015
BS EN 55014-1:2017+A11:2020 BS EN 55014-2:2015
BS EN 62479:2010
EN 300 328 V2.2.2
EN 301 489-1 V2.2.3
EN 301 489-17 V3.2.4
BS EN IEC 63000:2018
Winnenden, 2021-01-19
Alexander Krug
Managing Director
Authorized to compile the technical file

Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany
Copyright 2021
Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany
+49 (0) 7195-12-0
www.milwaukeetool.eu
Techtronic Industries (UK) Ltd Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK

References

• Track Tools with ONE-KEY™: Free Inventory App by Milwaukee®
• Milwaukee Tool Europe | Cordless Power Tools, Outdoor Tools, Hand Tools, PPE, Work wear. Storage and Accessories. | Milwaukee Tools Europe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>