LANCOM GS-3252P Fully Managed Access Switches User Guide
- June 9, 2024
- LANCOM
Table of Contents
LANCOM GS-3252P Fully Managed Access Switches
Hardware Quick Reference
LANCOM GS-3252P
INTRODUCTIONS
-
Configuration interface (Console)
Connect the configuration interface via the included serial configuration cable to the serial interface of the device you want to use for configuring / monitoring the switch. -
TP Ethernet interfaces 10M / 100M / 1G PoE+
Use Ethernet cables to connect the interfaces 1 to 36 to your PC or a LAN switch. -
TP Ethernet interfaces 10M / 100M / 1G
Use Ethernet cables to connect the interfaces 37 to 48 to your PC or a LAN switch. -
SFP interfaces 1G
Insert suitable LANCOM SFP modules into the SFP inter faces 49 to 52. Choose cables which are compatible with the SFP modules and connect them as described in the module’s documentation. -
Power connector (device back side)
Supply power to the device via the power connector. Please use the IEC power cable supplied or a country-specific LANCOM Power Cord.
Before initial startup, please make sure to take notice of the information
regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a
nearby power socket that is freely accessible at all times.
If an additional rear support surface is required for more stable mounting of
the switch, please use the LANCOM Switch Rack Mount L250.
Please observe the following when setting up the device
- The mains plug of the device must be freely accessible.
- For devices to be operated on the desktop, please attach the adhesive rubber footpads
- Do not rest any objects on top of the device and do not stack multiple devices
- Keep all ventilation slots of the device clear of obstruction
- Mount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets.
- Please note that support for third-party accessories (SFP and DAC) is not provided.
Mounting & connecting
System: off Device powered off
- System: green Device operational
- System: red Hardware error
- Link/Act/Speed: green
- Port LEDs show link / activity / port speed status
- PoE: green Port LEDs show PoE status
Mode / Reset button
- Short press Switching the port LED display
- Pressed until all port
- LEDs are off
- Device restart
- Pressed until all port
- LEDs glow permanently Configuration reset and device restart
TP Ethernet ports
- Off Port inactive or disabled
- Green Link 1000 Mbps
- Green, blinking Data transfer, link 1000 Mbps
- Orange Link ≤ 100 Mbps
- Orange, blinking Data transfer, link ≤ 100 Mbps
1G SFP ports
- Off Port inactive or disabled
- Green Link 1 Gbps
- Green, blinking Data transfer, link 1 Gbps
Hardware
- Power supply Internal power supply unit
- Environment Temperature range 0–40° C; short term temperature conditions 0-50°C; humidity 10–90%; non-condensing
- Housing Robust metal housing, 1 HU with removable mounting brackets for 19“ installation, network connectors on the front, 442 x 44 x 375 mm (W x H x D)
- Number of fans 1
Interfaces
- ETH 48 TP Ethernet ports 10 / 100 / 1000 Mbps, including 36 PoE+ ports
- SFP 4 SFP ports 1 Gbps 52 concurrent ports in total
Package Content
-
Mounting brackets Two 19” brackets for rack mounting;
If an additional rear support surface is required for more stable mounting of the switch, please use the LANCOM Switch Rack Mount L250, item no.: 61432, which is available as an accessory. -
Cable IEC power cord, serial configuration cable 1.5 m
LANCOM, LANCOM Systems, LCOS, LAN community and Hyper Integration are
registered trademarks.
All other names or descriptions used may be trademarks or registered
trademarks of their owners.
This document contains statements relating to future products and their
attributes.
LANCOM Systems reserves the right to change these without notice.
No liability for technical errors and / or omissions. 112114/1222
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>