StarTech com FHA-TV-WALL-MOUNT VESA TV Wall Mount User Manual

StarTech com FHA-TV-WALL-MOUNT VESA TV Wall Mount

Compliance Statements

Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Safety Statements

Safety Measures
Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.

Warning Statements

• Assemble this product according to the instructions.

• Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product.

• Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage.

• Weight capacity of the mount: 17.6 to 66 lb. (8 to 30 kg).

• Do not allow children to climb on this product, or use this product without proper supervision.

• This product is intended for indoor use only and should not be used outdoors.

• Do not over-tighten the screws. If any resistance is encountered, stop tightening.

• Assembling this product is a two-person task. Do not attempt to assemble this product and install equipment without assistance.

• Before adding equipment to this product, ensure the product has been properly assembled, and that the product can support the weight of the added equipment.

• Make sure all of the equipment has been properly secured before adjusting this product.

• Stored Energy Hazard! This product contains a spring mechanism which can cause the assembly and/or mounted equipment to move forcibly,
  and quickly, upwards. Always exercise caution when handling, or in close proximity to, the spring arm(s). Do not remove the mounted equipment unless the spring arm is moved to the highest position or (if possible) the spring force is adequately lowered to remove any danger posed. Failure to do so may result in property damage and/or serious personal injury.

• Pinch hazard! Keep your fingers clear from moving components.

Product Diagram

Product Dimensions

Side View

Product Information

Requirements
For the latest product information, technical specifications, manuals, and Declarations of Conformance, please visit:
www.StarTech.com/FHA-TV-WALL-MOUNT

TV

• Compatible VESA Mounting Hole Pattern
• VESA Plate: 75 x 75,100 x 100, 200 x 100, and 200 x 200
• VESA Plate with VESA Extension Plates: 300 x 300, 400 x 200, and 400 x 400.

Tools

• Phillips Head Screwdriver

Package Contents

Installation

Remove the VESA Plate from the Arm Assembly

1. Partially loosen the Top Nuts, located on the back of the VESA Plate, using the Wrench. The Top Nuts indicate the Up position of the VESA Plate.
2. Remove the Bottom Nuts, located on the back of the VESA Plate, using the Wrench. Set aside the Bottom Nuts as they will be used in a later step.
3. Slide out the bottom and lift upwards to remove the VESA Plate from the Arm Assembly. (Figure 1)

Mounting the Wall Mount

Fasten the Wall Mount to a Wood Stud or Concrete Wall
Warning! The TV wall mount is designed to be installed on a wood stud, solid concrete, or cinder block wall. The wall structure should be capable of supporting at least four times the weight of the mounted equipment.
The mounting hardware included with this product may not be adequate for installation on certain wall structures.
Contact a construction professional to install the wall mount. Failure to do so may result in personal injury and/or equipment damage.

Install the Decorative Covers

1. Gently Push-in the Decorative Covers onto the Wall Mount. (Figure 2)

Configure the VESA Plate to the TV Mounting Pattern
If the two mounting holes on the VESA Plate are not compatible with the mounting holes on the TV or display, use the VESA Extension Plates to create a compatible mounting hole configuration.

• Fasten the VESA Extension Plates, Left and Right, to the VESA Plate with the VESA Extension Plates Screws (x 8), using a Phillips Head Screwdriver. (Figure 3)

The VESA Extension Plates can be configured to various TV VESA mounting patterns, such as 300×300, 400×400, etc.

Mount a TV with a Flush Mounting Surface
To accommodate different TV designs, FHA-TV-WALL-MOUNT comes with five sets of screws of various lengths and diameters, two sizes of washers, and two sizes of spacers.

1. To select the combination of mounting hardware needed to use to attach the VESA Plate or VESA Extension Plates to the TV, complete the following:
   • Determine the depth of the mounting holes on the TV.
   • Determine the diameter of the mounting holes on the TV. Note: If using a TV with a flush mounting surface, you don’t  need to use any of the provided spacers.
2. Align the VESA Plate or the VESA Extension Plates with the mounting holes on the back of the TV.
3. Place the appropriately sized Display Washers (x 4) over the VESA Plate or the VESA Extension Plates.
4. Insert the appropriately sized M-Type Screws (x 4) through the Display Washers, the VESA Plate or VESA Extension Plates, and into the VESA Mounting Holes, located in the back of the TV. (Figure 4)
5. Tighten the appropriately sized M-Type Screws, using a Phillips Head Screwdriver.
   Warning! Do not overtighten the screws. If you encounter resistance while tightening the screws, stop tightening.
   

Mount a TV with a Recessed Mounting Surface
To accommodate different TV designs, the FHA-TV-WALL-MOUNT includes five sets of screws of various lengths and diameters, two sizes of washers, and two sizes of spacers.

1. Bridge the gap between the VESA Plate or VESA Extension Plates and the VESA Mounting Holes, located on the back of the TV. Select appropriately sized M-Type Screws (x 4) and pair them with an adequate combination of Spacers. Refer to the bullets and Figures 5 and 6.
   • Determine the Depth of the mounting holes on the TV.
   • Determine the Diameter of the mounting holes on the TV.
   • Refer to the images below to see the possible hardware combinations of Screws and Spacers.

2. Align the VESA Plate or the VESA Extension Plates with the mounting holes on the back of the TV.
3. Place the Display Washers, Large over the VESA Plate or the VESA Plate Extensions.
4. Insert the M6 x 30 Screws (x 4), M8 x 30 Screws (x4), or M8 x 50 Screws (x 4) through the Washers, Large the VESA Plate or VESA Extension Plates, the Spacers, and into the VESA Mounting Holes, located in the back of the TV. (Figure 7)
5. Tighten the appropriately sized M-Type Screws, using a Phillips Head Screwdriver.
   Warning! Do not overtighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening. Failure to do so could result in damage to the TV.
   

Attach a TV to the Arm Assembly
Warning! Ensure that the weight of the TV does not exceed the weight capacity of this product. Exceeding the weight capacity may result in personal injury and/or damage to the product, the attached equipment, and/or the mounting surface. This product can support the following weight: Up to 66 lbs (30 kg).
Attaching the TV is a two-person Job. Do not attempt to complete this task by yourself.
Continue to support the weight of the TV until the nuts (x 4) have been installed and adequately tightened.

1. Locate the Top Threaded Studs at the back of the VESA Plate.

2. Slide the partially loosened Top Nuts, located on the back of the VESA Plate Assembly, down into the Slots, located on the end of the Arm Assembly. (Figure 8)

3. Insert the Two Nuts, from Step 1 of Installation – Release the VESA Plate from the Arm Assembly, located on the back of the VESA Plate Assembly.

4. Use the provided Wrench to tighten all the Nuts (x 4).

Operation

Height Adjustment Tension of the Arm Assembly

1. Position the Arm Assembly Horizontally before adjusting. Locate the Height Tension Adjustment Screw, located on the Arm Assembly.
2. Using the 6 mm Hex Key rotate the Height Tension Screw Clockwise to Increase the Tension for Heavier/Larger TVs, and rotate Counterclockwise to Decrease the Tension for Smaller/Lighter TVs. (Figure 9)
   

Cable management

1. Route the TV Cables through the Cable Management Attachments, located under the Arm Assembly, and to the Power/AV Sources. (Figure 10)

Adjust the Tilt Tension

1. Locate the adjustment Bolts, on the back of the VESA Plate. (Figure 11)

2. Use the provided 4 mm Hex Key. Rotate Clockwise to Increase the Tension, and rotate Counterclockwise to Decrease the Tension.
   To set the TV at a fixed angle, tilt the TV to the desired angle and fully tighten the Tilt Tension Adjustment Screws, using the 4 mm Hex Key.

Warranty Information

This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Hard-to-find made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.

Reviews
Share your experiences using StarTech.com products, including product applications and setup, what you love about the products, and areas for improvement.

StarTech.com
Ltd.
45 Artisans
Crescent
London, Ontario
N5V 5E9
Canada

StarTech.com
LLP
4490 South
Hamilton Road
Groveport, Ohio
43125
U.S.A.

StarTech.com
Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom

StarTech.com
Ltd.
Siriusdreef 17-27
2132 WT
Hoofddorp
The Netherlands

FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

References

• VESA TV Wall Mount, Full Motion TV Mount - TV Mounts | StarTech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>