Q-TRAN TALO Sleek Flat Lens LED Aluminum Extrusion Instruction Manual
- June 9, 2024
- Q-TRAN
Table of Contents
Q-TRAN TALO Sleek Flat Lens LED Aluminum Extrusion Instruction Manual
INSTALLATION INSTRUCTIONS
ATTENTION: Please read all instructions BEFORE installation
- Product to be installed by a licensed electrician – Field modifications void warranty
- Use only with Class 2 power supply unit — Compatible for use with Q-Tran power supplies
- Surface mount
- Suitable for installation in storage area of a clothes closet when assembled as a finished fixture up to 4W/ft at Q-Tran facility
- Not rated for walkover
- Input Voltage: 24VDC
- Diagrams for representation only and not to scale
METHODS OF INSTALLATION
SURFACE MOUNTING METHOD
- VHB Adhesive Mount (page 5-6)
- Silicone Mount (page 7)
- Hidden Stainless Steel Clip Mount (page 8)
- Plastic T-BAR Clip Mount (page 9)
Cove, Under & over cabinet:
Ideal for offce, retail, hospitality, education, laboratory, and residential.
Shelf:
Ideal for offce, retail, hospitality, education, laboratory, and residential.
Display cabinet :
Ideal for retail and hospitality
Signage:
Ideal for lobby, retail, hospitality, institutional, and transportation.
COMPONENTS & HARDWARE
| HIDDEN STAINLESS STEEL CLIP | PLASTIC T-BAR CLIP |
|---|
SST02|
Standard 1″(15/16) grid clips
Included
| Flat Head Screw #4×5/8”
ACCESSORIES SOLD SEPARATELY
HINGE BRACKET; sold individually| Q-ANGLE; sold in pairs| Q-PIVOT; sold in pairs
HMB-M HMB-L HMB-XL|
Q-ANGLE|
Q-PIVOT
Included
- 4 SS #6×1.25” Flat head wood screws
- 2 SS 4-40 Flat head clip screws
- 2 SS 6-32 Fillister screws
Included
- SS #4-40×3/16 Flat head screws
- 2 #4×3/4 Pan Head screw
ADHESIVE SOLD SEPARATELY
SILICONE| VHB TAPE; sold in 15’ increment s
DOWSIL 832|
TAPE-VHB-IP20
NOTES
HIDDEN STAINLESS STEEL CLIP| PLASTIC T-BAR CLIP
- 2 clips provided for 4’ or less; 4 clips provided for greater than 4’
|
- 2 Clips provided per first 12”, 1 clip provided per additional
CONTINUOUS WIRING CONFIGURATION OPTIONS
Q-TRAN TALO Sleek Flat Lens LED Aluminum Extrusion Instruction Manual
NOTE: Additional wire methods include: S1 & S2: Connector/Wire Input only P1 & P2: Connector/Wire Input and Output
SURFACE MOUNTING METHOD
SURFACE PREPARATION
Temperature and environmental concerns:
- Ideal application environment is 70-100ºF in 50% humidity or less.
- Minimum application temperature: 50ºF
- This temperature and humidity should be maintained for 72 hours after application for maximum bond strength.
a. Using a 50/50 alcohol mix, thoroughly clean the backside of the
fixture and the surface area where fixture will be installed. Allow 5 minutes
to dry.
b. Peel back 0.5″ of the VHB tape’s protective film on one end and use
firm pressure to adhere it to the desired surface, avoiding air bubbles.
Continue peeling the film and adhering the tape in small sections until the
entire length is installed
For porous materials (Wood, Brick, Concrete etc.) apply two layers of paint or
primer to the surface. This will help create a better bonding surface for
these materials. These can be purchased from a local hardware store.
Concrete, Stone, Cinderblock, Metal, and Brick| Loctite Metal and Concrete
Two-Part Epoxy
---|---
ABS, Fiberglass, Plastic, and PVC| Loctite Plastic Two-Part Epoxy
Tile, Wood, Ceramic, Glass, or Metal| Loctite Clear Two-Part Epoxy
All Purpose| Strong Stik
SURFACE MOUNTING METHOD: VHB ADHESIVE
BEFORE installation, the surface must be thoroughly cleaned and dried for maximum bond strength. (Page 5)
Determine the TALO fixture(s) location and positioning on desired surface
before adhering fixture to surface. Make any necessary reference markings to
indicate fixture placement
a. To adhere the VHB adhesive, peel the white film back while evenly
applying the tape to the mounting side of the fixture. The red side should be
visible.
b. Remove the red film and position fixture in place according to your
previous reference marking(s).
Remove protective film from the surface of the fixture’s lens.
NOTES: EPOXY ALTERNATIVE: For improved bonding strength, apply a small
amount of epoxy at each end. Refer to table on for suggested
epoxies. These can be purchased at a local hardware store. Please follow all
manufacturer instructions for suggested epoxy.
SURFACE MOUNTING METHOD: SILICONE
- 2 clips provided for 4’ or less; 4 clips provided for greater than 4’
Determine the TALO fixture(s) location and positioning on desired surface;
evenly distribute clips. Make any necessary reference markings to indicate
where each clip is to be secured in place. Recommended every 24” – 30”.
a. Firmly press the silicone-coated clips on the marked reference points.
b. Wait for silicone adhesive to cure completely before snapping fixture
into place.
c. Snap fixture onto clips.
NOTE: Cure time is dependent on the type of silicone adhesive used. Refer
to silicone product manufacturer for accurate drying time.
Remove protective film from the surface of the fixture’s lens.
SURFACE MOUNTING METHOD: HIDDEN STAINLESS STEEL CLIPS
- 2 clips provided for 4’ or less; 4 clips provided for greater than 4’
Determine the TALO fixture(s) location and positioning on desired surface;
evenly distribute clips. Make any necessary reference markings to indicate
where each clip is to be secured in place. Recommended every 24” – 30”.
a. Secure clips using the #4 flat head hardware provided.
b. Ensure the screw head is flush with the clip’s base.
c. Snap fixture onto clips.
NOTE: Flat head screw type is dependent on surface/application material.
Alternative flat head screws may be required. Refer to the surface material
manufacturer for suggested screw type.
Remove protective film from the surface of the fixture’s lens.
SURFACE MOUNTING METHOD: PLASTIC T-BAR CLIPS
- 2 Clips provided per first 12”, 1 clip provided per additional foot.
Determine the TALO fixture(s) location and positioning on Snap fixture onto
T-BAR. desired surface; evenly distribute clips. Make any necessary reference
markings to indicate where each clip is to be secured in place. Recommended
every 12”.
Snap fixture onto T-BAR.
Remove protective film from the surface of the fixture’s lens.
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | sales@q-tran.com | www.q-tran.com Specification subject to change. Rev-01-12-23 9
References
- Your Name as Your Email | Hover Realnames
- LED Lighting Systems, Linear LED Lights, LED transformers | Q-Tran
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>