hyco Ara Instantaneous Inline Water Heater User Manual

June 9, 2024
hyco

hyco Ara Instantaneous Inline Water Heater

hyco-Ara-Instantaneous-Inline-Water-Heater-product

Usage

Effective low cost solution for light hand washing at a single basin. Compact design, energy efficient and easy to install. Buy with our compatible hot and cold tap as a set for convenience and confidence. Confirm that the flow rate and temperature performance is adequate for your application using the chart and tables provided.

Features and Benefits

  • Supplies hot water to a single outlet for light hand washing only
  • Bare wire heating system gives fast heat up time
  • Heats the water instantly as it flows through the unit
  • Energy efficient –no standing losses
  • 3.0 kW power rating
  • Easy to install, 13 amps connects to standard wiring
  • Ideal bought as a set with our hot and cold tap or for IN30T use with a Vega infrared tap (page 60)
  • Not suitable for use with thermostatic mixing valves or taps or to supply a single lever mixer tap
  • Must be used with a spray head tap
  • Supplied 1.6l/m flow restrictor must be fitted to the tap spout giving giving a temperature uplift of 27°C
  • This will give 42°C in summer, incoming water temp 15°C and 37°C in winter, incoming water temp 10°C.

Thermostatic Model Only

  • External electronic thermostatic control accurate to the nearest degree
  • LED temperature display
  • Energy saving – only uses the power required to deliver the chosen temperature
  • Heating power automatically adjusted to compensate for temperature, flow rate and water pressure variations
  • Temperature factory set at 38°C and can be adjusted by the user between 35°C and 50°C. In normal usage the maximum temperature is 37°C to 42°C.
  • After power interruption the unit will recall the last usage outlet temperature but must be turned back on using the touch screen.

Product Code| Includes

HCTAP1

| Power

(kW)

| Thermostatic| Max Flow Rate

(l/m) handwash*

| Standing Loss

(kWh/day)

---|---|---|---|---|---
IN30SET IN30| Yes

No

| 3.0| No| 1.7| 0
IN30TSET IN30T| Yes

No

| 3.0| Yes| 1.7| 0

Outer Casing
Easy clean high impact ABS

Heating Element
Bare-wire heating system

Controls (Thermostatic Model only)
Temperature display (°C)
Power on/ off button
+/- controls allow the user to set the required temperature.

Tap and Tap Spray Nozzles
See features and benefits section

Safety
Overheat temperature protection IN30 – 75°C, IN30T – 85°C. Thermostatic model – water temperature controlled to maintain user selected temperature between 35°C and 50°C as water pressure conditions vary.

IP Rating
IP24 – IN30
IP24 – IN30T

Installation
This appliance must be installed in a frost free environment.
The heater should be located as close as practical to the hot water outlet to avoid unnecessary heat losses through the pipework.

Plumbing
Must be installed by a suitably qualified person.

Minimum flow rate 1.2 l/m.
Minimum water pressure 0.5 bar.
Maximum water pressure 8.0 bar.
Water resistivity ≥ 1300 Ωcm.

Water Connection
Inlet/ Outlet 2 x 1/2” BSP male
(37mm apart centre to centre). Fittings required (not supplied):
2 x 15mm compression to 1/2” BSP female adapter.
Thermostatic model only is suitable for use with pre-heated water e.g. solar heating systems subject to maximum inlet water temperature 60°C.

Electrical Connection
Installation must comply
with current IET wiring regulations.
Single phase. Fuse rating guide 13 amps.
The product should be connected to the fixed wiring of the property via a suitably rated isolating switch with a contact separation of at least 3mm in all poles.
Cable pre-wired 0.7m.

Approvals
CE, UKCA

Standard Warranty

1 year parts or replacement warranty.

Product Code| Height

(mm)

| Width

(mm)

| Depth

(mm)

| Weight (kg)

Empty

---|---|---|---|---
IN30| 170| 135| 70| 0.9
IN30T| 130| 185| 90| 1.3
HCTAP1| 230|  | 170|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals